Gaggenau CI 292 601 User manual

*DJJHQDX
Installation instructions2
Notice de montage13
Instrucciones de instalación24
CI 292 601
CI 282 601
Cooktop
Surface de cuisson
Placa

2
en-us Safety Definitions
Table of Contents
Installation instructions
9Safety Definitions 2
IMPORTANT SAFETY INSTRUCTIONS 3
Safety Codes and Standards 3
Electric Safety 4
Related Equipment Safety 4
Proposition 65Warning 5
Before you begin 6
Tools and parts needed 6
Parts included 6
Cabinet Requirements 6
Countertop Requirements 6
Prepare Installation Space 7
Cutout dimensions for 30" cooktops 7
Cutout dimensions for 36" cooktops 8
Ventilation 8
Installation Procedure 9
Installing the heat shield 9
Sealing tape for flush installation 10
Secure the cooktop to countertop 10
Electrical Installation 11
Electrical requirements 11
Connect Electrical Supply 11
Check the Installation 12
Customer Service 12
9Safety Definitions
SafetyDefinitions 9WARNING
This indicates that death or serious injuries may
occur as a result of non-observance of this
warning.
9CAUTION
This indicates that minor or moderate injuries may
occur as a result of non-observance of this
warning.
NOTICE
This indicates that damage to the appliance or property
may occur as a result of non-compliance with this
advisory.
Note: This alerts you to important information and/or
tips.

3
9IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READANDSAVETHESEINSTRUCTIONS IMPORTANT: The appliance must be
installed by a qualified installer.
INSTALLER: leave these instructions with
this unit for the owner. Show the owner
the location of the circuit breaker or fuse.
Mark it for easy reference.
OWNER: Please retain these instructions
for future reference.
9WARNING
If the information in this manual is
not followed exactly, fire or shock
may result causing property damage
or personal injury.
9WARNING
Do not repair, replace or remove any
part of the appliance unless
specifically recommended in the
manuals. Improper installation,
service or maintenance can cause
injury or property damage. Refer to
this manual for guidance. All other
servicing should be done by an
authorized servicer.
Remove all tape and packaging before
using the appliance. Destroy the
packaging after unpacking the appliance.
Never allow children to play with
packaging material.
Hidden surfaces may have sharp edges.
Use caution when reaching behind or
under appliance.
This appliance is intended for use up to a
maximum height of 13,100 feet
(4,000 meters) above sea level.
Improper installation is not covered by
the warranty.
9WARNING
Wearers of electronic implants!
The appliance may contain
permanent magnets which may affect
electronic implants, e.g. heart
pacemakers or insulin pumps.
Therefore, during installation,
wearers of electronic implants must
maintain a minimum distance of
4 inch (10 cm) from the appliance.
Safety Codes and Standards
This appliance complies with one or more
of the following Standards:
▯UL 858, The Standard for the Safety of
Household Electric Ranges
▯UL 507, The Standard for the Safety of
Electric Fans
▯CAN/CSA-C22.2No. 113-M1984Fans and
Ventilators
▯CAN/CSA-C22.2No. 61-M89Household
Cooking Ranges
It is the responsibility of the owner and
the installer to determine if additional
requirements and/or standards apply to
specific installations.

9IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
4
Electric Safety
9WARNING
Before you plug in an electrical cord
or turn on power supply, make sure
all controls are in the OFF position.
If required by the National Electrical
Code (or Canadian Electrical Code), this
appliance must be installed on a separate
branch circuit.
The circuit breaker should have a contact
separation of at least 3mm on all poles.
Be sure your appliance is properly
installed and grounded by a qualified
technician. Installation, electrical
connections and grounding must comply
with all applicable codes.
Before installing, turn power OFF at the
service panel. Lock service panel to
prevent power from being turned ON
accidentally.
9WARNING
IMPROPER GROUNDING CAN RESULT IN A
RISK OF ELECTRIC SHOCK!
Related Equipment Safety
The appliance should only be used if
installed by a qualified technician in
accordance with these installation
instructions. The manufacturer is not
responsible for any damage resulting
from incorrect installation.
Never modify or alter the construction of
the appliance. For example, do not
remove leveling legs, panels, wire covers
or anti-tip brackets/screws.
To eliminate the risk of burns or fire by
reaching over heated surface units,
cabinet storage space located above the
surface units should be avoided. If
cabinet storage is to be provided, the risk
can be reduced by installing a hood that
projects horizontally a minimum of
5inches (127 mm) beyond the bottom of
the cabinet.
Verify that cabinets above the cooktop are
a maximum of 13" (330 mm) deep.
DO NOT install refrigerators,
dishwashers, ovens (without ventilation),
or washing machines below the cooktop.
Note: We strongly recommend the
installation of a ventilation system with
this appliance.
Consult a qualified electrician if the
grounding instructions are not
completely understood, or if doubt
exists as to whether the appliance is
properly grounded. DO NOT USE AN
EXTENSION CORD.

5
9IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
Proposition 65Warning:
This product may contain a chemical
known to the State of California, which
can cause cancer or reproductive harm.
Therefore, the packaging of your product
may bear the following label as required
by California:

&DQFHUDQG5HSURGXFWLYH+DUPZZZ3:DUQLQJVFDJRY
67$7(2)&$/,)251,$352326,7,21:$51,1*
:$51,1*

6
en-us Before you begin
Before you begin
Beforeyoubegin Tools and parts needed
▯Phillips Head Screwdriver
▯Pencil
▯Drill with ¼" (6mm) bit
▯Jigsaw
▯Tape Measure
Note: Additional materials may be necessary for
installation in solid surface countertops. Contact the
countertop manufacturer.
Parts included
Cabinet Requirements
The distance from the top of the cooktop to the bottom of
cabinets above must be a minimum of A=30" (762mm).
This distance can be reduced to A=24" (610mm) when
the bottom of the wood or metal cabinet is protected by
not less than ¼" (6.35 mm) flame-retardant millboard
covered with not less than no. 28gauge sheet metal,
0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)
aluminum or 0.020" (0.5mm) copper.
Verify that the cabinets above the cooktop are a maximum
of B=13" (330mm) deep.
Countertop Requirements
9WARNING
To reduce the risk of ignition of surrounding
combustible materials, install at least 2" (51 mm)
from both sidewalls and the rear wall.
The countertop must be level and horizontal. The stability
of the countertop must be maintained after the cut-out
has been made.
Solid surface countertops often require special
installations. For example, heat-reflective tape and
rounded corners may be necessary. Contact the
countertop manufacturer for instructions specific to your
countertop.
%
$

7
Prepare Installation Space en-us
Prepare Installation Space
PrepareInstallationSpace Create the cut-out in the countertop according to the
installation diagram. The angle of the cut surface to the
countertop must be 90°.
The lateral cut-out edges must be flat in order to ensure
that the retaining springs are positioned properly on the
appliance. With multi-layered countertops, secure strips
laterally in the cut-out if necessary.
After creating cut-out, remove shavings. Seal cut
surfaces in a heat- and water-resistant manner.
Observe minimum distance between device underside
and cabinet surfaces of 3/8" (10 mm).
The worktop into which the cooktop is installed must be
heat-resistant up to 140° F (90 °C).
The worktop must be reinforced if it is less than 13/16 inch
(20 mm) thick.
If the thickness of the worktop into which the cooktop is
installed does not comply with the specifications,
reinforce the worktop using a fire- and water-resistant
material until it reaches the minimum thickness.
Otherwise, sufficient stability cannot be assured.
▯The worktop into which the cooktop is installed should
withstand loads of approx. 133 lbs (60 kg).
▯Confirm the cooktop is level only after it has been
installed.
For flush installation in tiled countertops:
Note: If necessary, raise the support surfaces using heat
and water resistant strips.
Cutout dimensions for 30" cooktops
Model: CI 282601




PLQ

PLQ



   



 PP





[
¡

PD[5 



5

PLQ


8
en-us Prepare Installation Space
Cutout dimensions for 36" cooktops
Model: CI 292601
Ventilation
To assure that the appliance works correctly, the cooktop
MUST be sufficiently ventilated.
Since the ventilation in the lower section of the appliance
requires a sufficient supply of fresh air, the cabinet must
be designed accordingly. The following is required for
this:
▯A minimum clearance between the rear of the cabinet
and the kitchen wall, and between the surface of the
worktop and the upper area of the drawer.
▯An opening at the top to the rear of the cabinet.
▯If the minimum clearance of 13/16 inch (20mm) is not
provided at the rear of the cabinet, you must create an
opening on the underside.
PLQ 
 
PLQ   



   



 PP
PD[5 



5

  


[
¡





PLQ 

PLQèç¼ʓʘ
PLQ
 PP
PLQë
PLQèè¼ʓʘ
 PP
PLQèç¼ʓʘ
 PP

9
Installation Procedure en-us
▯If the inside of the cabinet is no wider than
291/2inch (750 mm), make cutouts in the side panels.
Note: If the appliance is installed in an island unit or
another installation that is not described here, you must
ensure that the cooktop is sufficiently ventilated.
Installation Procedure
InstallationProcedure 9CAUTION
Sharp edges. Use protective gloves when installing
the cooktop.
Note: The appliance is heavy. It is advisable to install it
with a second person.
Installing the heat shield
9CAUTION
Sharp edges. Use protective gloves when installing
the plate.
For safety reasons, the heat shield must be properly
installed when closed cabinets are used. This prevents
components from overheating as a result of the
recirculation of hot air from the cooktop.
The heat shield is the same width as the cooktop. For
shipping, it is screwed to the bottom of the burner box.
After unpacking the cooktop, unscrew the heat shield.
The heat shield will be able to rotate freely, as shown in
the illustration.
$ê
PLQ
 PP


10
en-us Installation Procedure
Sealing tape for flush installation
Attach the adhesive sealing tape around the edges of the
countertop.
Note: Do not apply the sealing tape to the cooktop.
Secure the cooktop to countertop
9CAUTION
Do not let the glass drop into place. Make sure that
it is supported along a broad area of the edges
when carefully placing the cooktop into the cutout.
The appliance must be secured from below using the
hold-down brackets provided, so it does not slip.
Note: Protect delicate countertops by placing a wooden
disk underneath.
1. Rotate the appliance and position it so that the screws
provided are seated loosely in the holes. Move the
hold-down brackets so that the appliance can be
placed in the cutout.
2. Place the appliance carefully into the cutout.
3. Insert the clamping screws into the hold-down
brackets and secure the appliance to the countertop.
Tighten screws.