GalileoSky v 5.0 User manual

Switching on Galileosky
5.0, 5.1 Devices for the
First Time
User Manual
www.galileosky.com

Switching on Galileosky 5.0, 5.1 Devices for the First ime
version 6 dated from June 19, 2018
2
Contents
Necessary ools, Devices, Materials ........................................................ 3
Preparing of Galileosky Device to Switch-on ............................................ 4
Preparing of a tracking device socket unit ............................................. 4
SIM-cards inserting ................................................................................ 5
Preparing antennas ................................................................................ 6
Preparing of Device via the Configurator .................................................. 8
Monitoring Software Setting ...................................................................... 9

Switching on Galileosky 5.0, 5.1 Devices for the First ime
version 6 dated from June 19, 2018
3
Necessary Tools, Devices,
aterials
Before connecting the Galileosky racking device (hereinafter – tracking device, device)
you should have:
1. Power supply: 12V and more, not less than 1А
2. SIM-card with «GPRS» и «SMS» activated
3. Windows-based computer with installed Galileosky devices configuration software
– the Configurator

Switching on Galileosky 5.0, 5.1 Devices for the First ime
version 6 dated from June 19, 2018
4
Preparing of Galileosky
Device to Switch-on
Preparing of a tracking device socket unit
ogether with a device you get a counterpart of socket and several crimped conductors.
On the back of the case there is a schematic representation of the contacts to be connected
and location of main technological holes (Pic. 1).
A EN ION! he symbol of terminal board key is sometimes perceived as a connection
strap between RS232 and RS485 contacts (tracking device v5.0) or Vol0 and 1-Wire
(tracking device v2.2.8). Be careful, there should not be any connection strap!
he order of terminal board assembling is as follows:
1. Rotate the terminal board in such a way that the key has been at the top of the socket
and the places of conductors connection have been directed towards the user (Pic. 2);
Pic. 1
Scheme of contacts
location
Pic. 2
Terminal boards

Switching on Galileosky 5.0, 5.1 Devices for the First ime
version 6 dated from June 19, 2018
5
2. urn the contacts the locking mechanisms up and along the sides and insert them
into the socket until clicking position (Pic. 3).
A EN ION! When you install the conductors observe the polarity – the red wire is used
as a positive conductor and the black wire is used as a negative one.
SI -cards inserting
he order of SIM-cards inserting is the following:
 Press the SIM holder button with something sharp (clip, toothpick) and eject the SIM-
holder (Pic. 4);
 Insert the SIM-card into the holder contacts up (Pic. 5);
Pic. 3
Crimped terminal
conductor
Pic. 4
Ejecting of SI -holder
Button
SI holder

Switching on Galileosky 5.0, 5.1 Devices for the First ime
version 6 dated from June 19, 2018
6
 Carefully without applying excessive force insert the SIM-holder with the card into
the tracking device until locking focusing on the key drawn on the tracking device
body (Pic. 6).
A EN ION! Use SIM-cards with activated GPRS and SMS services.
Preparing antennas
ogether with the racking device you get a GSM-antenna and a GLONASS/GPS-
antenna. he antennas differ in appearance and functionality. he GSM-antenna (Pic. 7)
is a passive one and is connected to the GSM-antenna plug.
he GLONASS/GPS-antenna (Pic. 8) is an active one. It means that it needs a power
connection for normal operation. he antenna is connected strictly to the GLONASS/GPS
Pic. 5
Inserting the SI -card
Pic. 6
SI -card inserting
scheme
Pic. 7
GS -antennas

Switching on Galileosky 5.0, 5.1 Devices for the First ime
version 6 dated from June 19, 2018
7
antenna plug. he GLONASS/GPS antenna plug of the tracking device provides the
necessary voltage for operation.
Connect the GSM-antenna and the GLONASS/GPS-antenna to correspondent plugs as
it is shown in Picture 9.
Pic. 8
GLONASS/GPS-
antennas
Pic. 9
Connecting
GLONASS/GPS-
antenna

Switching on Galileosky 5.0, 5.1 Devices for the First ime
version 6 dated from June 19, 2018
8
Preparing of Device via the
Configurator
Before using Galileosky devices you have to configure them with the help of service
software “Configurator” (hereinafter – the Configurator). he order of downloading and
installation is the following:
 urn on the Windows-based computer and go to the Galileosky web-site using the
following link https://galileosky.com/podderzhka/programmyi.html
 Download the latest version of the Configurator;
 Install the Configurator on the computer with administrator rights;
 Authorize the Configurator to work through the Internet in operating system settings;
After installation of the Configurator you can start device settings:
 Apply the voltage from 12V to the tracking device and connect it to the computer via
USB cable;
A EN ION! he power is not fed through USB-interface. he device must be connected
to the external power supply.
 Start the Configurator and move to “Settings” tab -> “Data transmission” tab (Pic.
10);
 Set APN of the chosen cellular service provider;
 Configure the data processing monitoring server and the port through which it works;
 press “Apply” button;
 Reboot the device by pressing the “Restart the device” button in the “Device” tab of
the Configurator.
Pic. 10
Data transmission setting

Switching on Galileosky 5.0, 5.1 Devices for the First ime
version 6 dated from June 19, 2018
9
onitoring Software Setting
he next step is to configure the monitoring program to which the data from the device
should be sent. he settings order is the following:
 Start the monitoring program and go to monitoring object creation section;
 Specify the name of the object (any), type of the object «GALILEOSKY v 5.0», in
unique ID field enter the IMEI of the device;
Initial setup is completed. Go to the “Monitoring” tab and check the monitoring object
state (Pic. 12).
In case of any failure, it is possible to view the information about the operation of the
device in the “ roubleshooting” tab of the Configurator. o execute the troubleshooting
put ticks in the entries required.
Pic. 11
onitoring object setting
Pic. 12
onitoring Software tab

Switching on Galileosky 5.0, 5.1 Devices for the First ime
version 6 dated from June 19, 2018
10
The device is ready to operate.
RSA “Galileosky”, LLC produces satellite monitoring equipment for GPS and
GLONASS real time vehicles monitoring. he tracking devices determine the mobile
object location recording the time and route as points with geographical coordinates
and send the data to the server to be further processed and sent to the traffic controller
panel.
In addition, a number of other vehicle parameters are recorded: the state of analog
and discrete inputs of the tracking device and the state of digital interfaces.
he tracking devices can be used in any vehicle.
Pic. 13
Troubleshooting tab