Gardenline ALDI HTH250 User manual

ALDI guarantees that our exclusive brand products are developed to
our stringent quality specications. If you are not entirely satised with this
product, please return it to your nearest ALDI store within 60 days from
the date of purchase for a full refund or replacement, or take advantage of
our after sales support by calling the supplier’s Customer Service Hotline.
Made in China
GARDENLINE is a registered trademark of ALDI Stores
DISTRIBUTED BY:
ALDI STORES
1 SARGENTS ROAD
MINCHINBURY NSW 2770
www.aldi.com.au
MODEL:HTH250/240P PRODUCT CODE: 59823 03/2018
AFTER SALES SUPPORT
 1300 855 831  [e-mail]
User Manual
HEDGE TRIMMER PETROL
HTH250/240P
AUS
Original instructions
Vers.No. 171102
Overview 04
Utilisation 05
Contents of box 06
Explanation of symbols 07
Introduction 09
Layout 10
Scope of delivery 10
Intended use 11
Safety information 12
Before starting the equipment 16
Attachment and operation 18
Working instructions 20
Maintenance cleaning and servicing 23
Technical data 27
Storage 28
Transport 29
Disposal and recycling 30
Troubleshooting 31
Warranty Details 33
Repair and Refurbished Goods or Parts Notice 34
Contents

AFTER SALES SUPPORT 7
 1300 855 831  [e-mail]
MODEL: HTH250/240P PRODUCT CODE: 59823 03/2018
Read, understand and follow all warnings.
Read the complete user guide before using the appliance.
Wear work gloves.
Always wear non-skid safety shoes with cut protection
when using this product.
Protect the tool from getting wet!
Pay attention! Hot surfaces.
Wear safety goggles!
Use hearing protection!
Attention! Risk of injury.
Explanation of symbols
The use of symbols in this manual is intended to draw your attention to possible risks.
The safety symbols and the explanations that accompany them must be perfectly
understood. The warnings in themselves do not remove the risks and cannot replace
correct actions for preventing accidents.
AUS
HTH250/240P Explanation of symbols

Start lever (choke) 'cold start'
Start lever (choke) 'warm start and work'
No open re in the working area!
Guaranteed sound power level of the device.
108
AUS
Explanation of symbols HTH250/240P
8AFTER SALES SUPPORT
 [e-mail]  1300 855 831
MODEL:HTH250/240P PRODUCT CODE: 59823 03/2018

HTW250/240P Introduction
AFTER SALES SUPPORT 9
 00800 4003 4003  [e-mail]
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
I. INTRODUCTION
Congratulations on choosing to buy a GARDENLINE®product.
All products brought to you by GARDENLINE®are manufactured to the highest
standards of performance and safety, and as part of our philosophy of customer
service and satisfaction, are backed by our comprehensive 5 Year Warranty.
We hope you will enjoy using your purchase for many years to come.
Note:
According to the applicable product liability law the manufacturer of this device is not
liable for damages which arise on or in connection with this device in case of:
• improper handling,
• non-compliance with the instructions for use,
• repairs by third party, non-authorised skilled workers,
• installation and replacement of non-original spare parts,
• improper use.
Recommendations:
Read the entire text of the operating instructions prior to the assembly and operation
of the device.
These operating instructions are intended to make it easier for you to get familiar
with your device and utilise its intended possibilities of use.
The operating instructions contain important notes on how to work safely, properly
and economically with your machine and how to avoid dangers, save repair costs,
reduce downtime, and increase the reliability and working life of the machine.
In addition to the safety regulations contained herein, you must in any case comply
with the applicable regulations of your country with respect to the operation of the
machine.
Keep the operating instructions in a clear plastic folder to protect them from dirt and
humidity, store them near the machine. The instructions should be read and careful-
ly understood by each operator prior to using the machine. Only persons who have
been trained in the use of the machine and are aware of the related dangers and
risks should be allowed use the machine. The local required minimum age must be
met.
In addition to the safety notes contained in these operating instructions and any
specic regulations in your country, the generally recognised technical rules for the
operation of identically constructed machines must be observed.
AUS
HTH250/240P Introduction
AFTER SALES SUPPORT 9
 1300 855 831  [e-mail]
MODEL: HTH250/240P PRODUCT CODE: 59823 03/2018

Layout/Scope of delivery HTW250/240P
10 AFTER SALES SUPPORT
 [e-mail]  00800 4003 4003
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
II. L AYOUT (Fig. 1&2)
1 Cutting device
2 Hand guard
3 Front handhold
4 Choke
5 Cranking rope with handle
6 ON/OFF switch
7 Throttle lock-out switch
8 Air lter cover
9 Wing screw
10 Zerk tting (grease tting)
11 Fuel pump
12 Fuel tank cap
13 Slider
14 Throttle trigger
15 Rear handle
16 Hexagon wrench 8/10mm
17 Allen key 4mm
18 Allen key 5mm
19 Spark plug spanner
20 Fuel mixing bottle
21 Spark plug connector
III. SCOPE OF DELIVERY
Petrol Hedge trimmer (1x)
Blade Guard (2x)
Spark plug spanner (1x)
Fuel mixing bottle (1x)
Instruction manual (1x)
Warranty card (1x)
Allen key 4mm (1x)
Allen key 5mm (1x)
Open end wrench 8/10mm (1x)
AUS
Layout/Scope of delivery HTH250/240P
10 AFTER SALES SUPPORT
 [e-mail]  1300 855 831
MODEL:HTH250/240P PRODUCT CODE: 59823 03/2018

HTW250/240P Introduction
AFTER SALES SUPPORT 9
 00800 4003 4003  [e-mail]
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
• Open the packaging and take out the equipment with care.
• Remove the packaging material.
• Check that all listed contents are present.
• Inspect the equipment and parts for any damage. Please contact the helpline if
anything is missing.
• If possible, keep the packaging until the end of the guarantee period.
• Read the operating instructions fully to familiarise yourself with the tool prior to
using it.
• Only use original accessories and spare parts. Spare parts are available by
contacting the helpline.
• Specify the part numbers when you contact the helpline.
m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic bags, lm and small parts!
There is a risk of swallowing and suffocation!
IV. INTENDED USE
This hedge trimmer has been designed to cut soft, freshly grown hedge
material. It is not suitable for cutting branches, tough wood or other material to be
cut.
The machine has been designed to be operated by one person.
The hedge trimmer may be used only for cutting hedges, bushes and shrubs.
Alternative use not specied in these instructions can damage the hedge trimmer or
severely injure the user.
The machine is to be used only for its prescribed purpose. Any other use is deemed
to be a case of misuse. The user / operator and not the manufacturer will be liable
for any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial, trade
or industrial applications. Our warranty will be voided if the machine is used in
commercial, trade or industrial businesses or for equivalent purposes.
The operating instructions as supplied by the manufacturer must be followed at all
AUS
HTH250/240P Scope of delivery/Intended use
AFTER SALES SUPPORT 11
 1300 855 831  [e-mail]
MODEL: HTH250/240P PRODUCT CODE: 59823 03/2018

Layout/Scope of delivery HTW250/240P
10 AFTER SALES SUPPORT
 [e-mail]  00800 4003 4003
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
times to ensure that the equipment is used properly. Any use which is not expressly
permitted in the manual may result in damage to the equipment and place the user
in serious danger. Observe the restrictions in the safety instructions.
Non-permitted users:
Persons who are not familiar with the operating manual, children, young people
under the age of 18 as well as persons under the inuence of alcohol, drugs or
medication shall not be permitted to operate the unit.
WARNING! For your own safety, please thoroughly read this manual and the
general safety instructions before turning the device on. If you give the
device to third parties, always include these instructions.
V. SAFETY INFORMATION
Working Safely
Before starting this device, read and keep to the following advice. Also observe the
safety provisions applicable in the respective country, in order to protect yourself
and others from possible injury.
Repair works on the device must be carried out by the manufacturer or by
companies appointed by the manufacturer respectively.
Primary users
Persons working for the rst time with the hedge trimmer must obtain a practical
instruction to the use of the hedge trimmer and the operator protection equipment by
an experienced operating person.
• Be attentive. Be careful what you do. Behave sensibly when working. Do not use
the device when you are tired or under the inuence of drugs, alcohol or
medication. One moment of carelessness when using the device can result in
serious injuries.
• Make yourself familiar with the equipment before using it, by reading and
understanding the operating instructions. Insufciently informed operators may
put at risk their own and the health of other persons.
• Do not use the machine for unsuitable purposes (see 'Intended use').
• Avoid abnormal posture. Provide a safe standing position and keep your balance
at all times.
AUS
Intended use/Safety information HTH250/240P
12 AFTER SALES SUPPORT
 [e-mail]  1300 855 831
MODEL:HTH250/240P PRODUCT CODE: 59823 03/2018

HTW250/240P Introduction
AFTER SALES SUPPORT 9
 00800 4003 4003  [e-mail]
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
• Wear suitable work clothes:
- Do not wear loose-tting clothes or jewellery; they can catch in moving parts.
- Gloves and slip-proof shoes
- Hairnet in case of long hair
• Wear protective clothing:
- ear protection
- protective goggles or face protection
- protective gloves
- safety boots
- certicated hardhat in situations where injuries to the head might be expected.
• We recommend to wear leg protection and a safety jacket.
• Keep your workplace in an orderly condition! Untidiness can result in accidents.
• Take into consideration environmental inuences:
- Do not expose the hedge trimmer to rain.
- Do not use the hedge trimmer in a damp or wet environment.
- Delay the work in case of disadvantageous weather (rain, snow, ice, wind) –
increased risk of accidents!
- Provide for good illumination.
- Do not use the hedge trimmer near inammable liquids or gases.
• Familiarize yourself with your environment and pay attention to possible dangers
such as wires and power lines. Remember, you may not be able to hear because
of the motor noise.
• Never leave the hedge trimmer unattended.
• For breaks the hedge trimmer has to be put down in such a manner that no person
will be endangered. Assure the hedge trimmer against unauthorised access.
• Persons under the age of 18 must not operate the device.
• Keep other persons away.
• The operator is responsible for accidents or risks which occur to other persons or
their properties.
• The operator is responsible to third persons within the area of operations.
• Keep children away.
• Do not allow other persons, especially children, to touch the tool or motor. Keep
them away from your working area.
• Do not use a blunt, broken or otherwise damaged cutting device.
• Be sure that the cutting device is moving before you start cutting.
• Do not overload the machine! You work better and safer in the given performance
range.
• Only operate the machine with complete and correctly attached safety equipment
AUS
HTH250/240P Safety information
AFTER SALES SUPPORT 13
 1300 855 831  [e-mail]
MODEL: HTH250/240P PRODUCT CODE: 59823 03/2018

Layout/Scope of delivery HTW250/240P
10 AFTER SALES SUPPORT
 [e-mail]  00800 4003 4003
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
and do not alter anything on the machine that could impair the safety.
• Do not modify the device or parts of the device respectively.
• Do not use any blades which do not comply with the indicated characteristics of
this instruction manual.
The use of other tools and other accessories can signify a risk of injury for
you.
If the cutting mechanism strikes any foreign object or the hedge trimmer starts
making any unusual noise or vibration, shut off the power source and allow the
hedge trimmer to stop. Disconnect the spark plug wire from the spark plug and take
the following steps:
• inspect for damage;
• check for, and tighten, any loose parts;
• have any damaged parts replaced or repaired with parts having equivalent
specications
- carrying out repair works
- maintenance and cleaning
- carrying out servicing and repair works, removal of faults
(including jammed blades)
- transport and storage
- leaving the hedge trimmer (also for short-term interruptions)
• Maintain your hedge trimmer with care:
- Keep your tools sharp and clean in order to be able to work better and safer.
- Keep handles dry and free of oil and grease.
- Follow the maintenance instructions.
• Check the machine for possible damage:
- Before continuing to use the machine, the protective devices must be inspected
to ensure that they work perfectly and with their intended function.
- Check whether the movable parts function perfectly and do not stick or whether
the parts are damaged. All parts must be correctly installed and full all
conditions to ensure perfect operation of the hedge trimmer.
- Damaged guards and parts must be properly repaired or exchanged by a
recognized, specialist workshop; insofar as nothing else is stated in the
instructions for use.
- Damaged or illegible safety labels should be replaced immediately.
• Do not allow any tool key to be plugged in! Before switching on, check always that
wrenches and adjusting tools are removed.
• Store unused equipment in a dry, locked place out of the reach of children.
• Do not repair the device unless you are qualied for such kind of work. Do not
AUS
Safety information HTH250/240P
14 AFTER SALES SUPPORT
 [e-mail]  1300 855 831
MODEL:HTH250/240P PRODUCT CODE: 59823 03/2018

HTW250/240P Introduction
AFTER SALES SUPPORT 9
 00800 4003 4003  [e-mail]
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
carry out repair operations on the machine other than those described in
section 'Maintenance' but contact the manufacturer or authorized customer
service centres.
Use only original spare parts. Accidents can arise for the user through the use of
other spare parts. The manufacturer is not liable for any damage or injury resulting
from such action.
Safe handling of fuels
Fuels and fuel vapours are ammable and may cause serious injury on the skin or
when inhaled. Therefore be careful and provide sufcient ventilation when handling
with fuels.
• Stop the engine and allow the device to cool down before fuelling it.
• Do not smoke and avoid open ames when fuelling.
• Wear gloves when fuelling.
• Never refuel or drain the tank indoors.
• Avoid spilling of fuel or oil. Clean the hedge trimmer immediately when you have
spilled fuel or oil. Change your clothes immediately when you have spilled fuel or
oil on them.
• Make sure that no fuel can come into the soil.
• Carefully close the tank cap after fuelling and check that it does not get loose
during operation.
• Check that there is no leakage on the tank cap and fuel lines. If there are leaks
this device may not be started. Go away at least three metres from the fuelling
place to start the device.
• Only transport and store fuels in containers approved and identied for this.
• Keep children away from fuels.
• Never store the hedge trimmer or fuel container inside where there is an open
ame, such as near a water heater.
• To reduce the re risk keep the motor and silencer free from cutting remainders,
leaves and lubricants.
Residual risks
Even if used properly, residual risks can exist even if the relevant safety regulations
are complied with due to the nature of the product.
Residual risks can be minimised if the 'Safety information' and the 'Intended use' as
well as the whole of the operating instructions are observed.
Observing these instructions, and taking proper care, will reduce the risk of personal
injury or damage to the equipment.
AUS
HTH250/240P Safety information
AFTER SALES SUPPORT 15
 1300 855 831  [e-mail]
MODEL: HTH250/240P PRODUCT CODE: 59823 03/2018

Layout/Scope of delivery HTW250/240P
10 AFTER SALES SUPPORT
 [e-mail]  00800 4003 4003
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
• Injury by catapulted parts.
• Breaking or catapulting of blade pieces.
• Burning when touching hot parts.
• Impairment of hearing when working on the machine for longer periods of time
without ear protection.
In addition, in spite of all the precautionary measures taken, non-obvious
residual risks can still exist.
Store all safety notices and instructions for the future.
VI. BEFORE STARTING THE EQUIPMENT
The hedge trimmer is supplied without fuel.
Fuel the hedge trimmer as described under 'Fuelling'.
Fuelling
• This device is operated by a mixture from regular petrol (unleaded) and two-stroke
engine oil.
Utmost care is required when handling fuel and oil. Keep away smoke and
open ames (risk of explosion).
Petrol
Petrol: Octane number at least 91 RON unleaded
• Do not ll in leaded petrol, diesel or other non-approved fuels.
• Do not use petrol having a smaller octane number than 91 RON. This may lead to
severe engine damages due to increased engine temperatures.
• If you frequently operate the device at high speeds, you should use petrol with a
higher octane number.
• The use of unleaded petrol is recommended for environment protection reasons.
Two-stroke engine oil:
according to JASO FC or ISO EGD specications
AUS
Safety information/Before starting the equipment HTH250/240P
16 AFTER SALES SUPPORT
 [e-mail]  1300 855 831
MODEL:HTH250/240P PRODUCT CODE: 59823 03/2018

HTW250/240P Introduction
AFTER SALES SUPPORT 9
 00800 4003 4003  [e-mail]
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
Do not use
- four-stroke oil or two-stroke oil for water-cooled outboard engines
- mixtures ready for use from petrol stations
Mixing
Ratio of mixture: 40:1
Petrol Two-stroke engine oil 2.5% (40:1)
1 litres / 0.025 litres
2 litres / 0.05 litres
5 litres / 0.125 litres
10 litres / 0.25 litres
• Measure the oil quantity accurately as a small deviation of it has a large effect on
the ratio of mixture in particular for small fuel quantities.
• Do not change the ratio of mixture. This will lead to more residues of combustion,
a higher fuel consumption, a decrease of output or damages to the engine.
Mix petrol and oil in a clean container approved for petrol and appropriately
identied. Use a fuel container with overll protection.
1. At rst ll in half the quantity of petrol to be mixed.
2. Then ll in the total amount of oil.
3. Shake the fuel mixture.
4. Fill in the remaining quantity of petrol.
Fuels have only a limited shelf-life, they are subject to ageing. Outdated fuels and
fuel mixtures may result in starting problems. Therefore, mix only that quantity of
fuel which you can use within a month. Only store fuels in containers approved and
identied for this. Keep fuel containers in a dry and safe area.
Make sure that fuel containers are kept out of the reach for children.
Caution! Prior to starting the machine learn how to put it out of action in emergency
cases.
AUS
HTH250/240P Before starting the equipment
AFTER SALES SUPPORT 17
 1300 855 831  [e-mail]
MODEL: HTH250/240P PRODUCT CODE: 59823 03/2018

Layout/Scope of delivery HTW250/240P
10 AFTER SALES SUPPORT
 [e-mail]  00800 4003 4003
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
Fuelling the hedge trimmer (Fig. 1)
• Stop the engine and allow it to cool down.
• Wear protective gloves.
• Avoid eye and skin contact.
• Strictly follow the instructions under 'Safe handling with fuels'.
1. Only fuel the hedge trimmer in the open or in sufciently ventilated rooms.
2. Clean the area around the ller neck. Contamination in the tank may result in
malfunction.
3. Shake the container once more before pouring the fuel mixture into the tank.
4. Carefully open the fuel tank cap (12) to allow possible overpressure to release.
5. Carefully ll the fuel mixture up to the lower edge of the ller neck.
6. Close the fuel tank cap (12). Check that the fuel tank cap (12) is tight.
7. Clean the fuel tank cap (12) and the area around it.
8. Check the tank and the fuel lines for leaks.
9. Operate the fuel pump (11) if required.
10. Before starting the engine move at least three metres away from the fuelling
place.
VII. ATTACHMENT AND OPERATION
You may not start to operate the machine until you have read these operating
instructions, observed all the instructions given and completely and properly
assembled the machine!
- Make sure that the ON/OFF switch (6), the throttle lock-out switch (7) and the
throttle trigger (14) function perfectly. (Fig. 1)
- This hedge trimmer is only allowed to be started after it is completely assembled.
- Support the hedge trimmer when starting and hold it rmly. Make sure that the
cutting device can move freely.
To start the hedge trimmer:
1. Keep a safe distance to ammable materials.
2. Have a safe standing position.
3. Place the hedge trimmer on the ground in front of you, with the cutting device
pointing away from your body.
4. Put your right foot tip in the rear handle.
5. Hold the front handle with your left hand.
AUS
Before starting the equipment/Attachment and operation HTH250/240P
18 AFTER SALES SUPPORT
 [e-mail]  1300 855 831
MODEL:HTH250/240P PRODUCT CODE: 59823 03/2018

HTW250/240P Introduction
AFTER SALES SUPPORT 9
 00800 4003 4003  [e-mail]
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
Starting with cold engine (Fig. 1)
1. Slide the ON/OFF switch (6) to the position 'I'.
2. Carefully press on the fuel pump (11) several times until fuel comes into the
pump.
3. Slide the choke (4) to 'cold start'.
4. Slowly pull the cranking rope with its handle (5) until you feel a resistance.
5. Pull the cranking rope quickly and then guide it back slowly. Do not fully pull
out the cranking rope and do not allow the cranking handle to strike against the
engine.
6. When the engine starts slide the choke (4) to 'warm start and work'.
7. Allow the device to warm up for approx. 1 minute before starting the work.
Stopping the engine (Fig. 1)
1. Release the throttle trigger (14).
2. Slide the ON/OFF switch (6) to the '0' position.
Starting with warm engine (Fig. 1)
1. Slide the ON/OFF switch (6) to the position 'I'.
2. Slide the choke lever (4) to 'warm start and work'.
3. Hold the cranking handle (5) and pull the cranking rope until the engine starts.
Throttle lock-out switch (Fig. 1)
1. Hold the hedge trimmer on its rear handle (15) and press the throttle lock-out
switch (7).
2. Hold the front handhold (3) with your other hand.
3. Press the throttle trigger (14).
4. The cutting device will start moving.
• If you release the throttle trigger, the cutting device will stop and the engine will
idle.
If the cutting device runs in spite of non-pressed throttle trigger, you have to reduce
the idle speed. (See 'Maintenance'.)
AUS
HTH250/240P Attachment and operation
AFTER SALES SUPPORT 19
 1300 855 831  [e-mail]
MODEL: HTH250/240P PRODUCT CODE: 59823 03/2018

Layout/Scope of delivery HTW250/240P
10 AFTER SALES SUPPORT
 [e-mail]  00800 4003 4003
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
Adjustments on the hedge trimmer
Adjusting the rear handle. (Fig. 1)
To make working with the hedge trimmer easier it is possible to choose one of the 3
working positions of the rear handle (15).
• When adjusting the throttle trigger (14) can not be pressed.
1. Use your left hand to hold the hedge trimmer on its front handhold (3).
2. Pull the slider (13) and turn the rear handle (15) to your desired position.
3. Release the slider (13). Make sure that the unlocking device engages again and
that the rear handle (15) is secured.
VIII. WORKING INSTRUCTIONS
Carry out the following checks before starting and regularly during working with the
hedge trimmer:
• Is the hedge trimmer assembled completely and properly? Check also that all nuts
and screws are tightened. Screws on the cutting device: See 'Maintenance'.
• Is the hedge trimmer in good and safe condition? Do all safety devices properly
work?
• Is the fuel tank lled?
• Is the cutting device undamaged and sharpened?
• Are engine and silencer free from deposits, leaves or emerging lubricants.
• Is handhold clean and dry – free of oil, grease and resin?
• Is workplace free of risks to stumble?
• Do you wear the required protective equipment?
• Did you read and understand all advices?
• Is the throttle trigger easy-running and functioning?
• Does the ON/OFF switch properly work?
• Does the cutting device always stop in idle mode?
If the cutting device moves during idling the idle speed must be reduced
(see 'Adjusting the idle speed').
• Check that the gearbox is sufciently lubricated (see 'Maintenance').
General behaviour when working with the hedge trimmer
• Never work alone. Another person should stay close enough to hear calls for help.
• Keep children, bystanders and animals at a distance (15m min.) from your working
AUS
Attachment and operation/Working instructions HTH250/240P
20 AFTER SALES SUPPORT
 [e-mail]  1300 855 831
MODEL:HTH250/240P PRODUCT CODE: 59823 03/2018

HTW250/240P Introduction
AFTER SALES SUPPORT 9
 00800 4003 4003  [e-mail]
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
area.
• Do not work on snow, ice or other slippery ground – slip hazard.
• Do not work under insufcient light conditions (e.g. fog, rain, snow urry or
twilight).
• Scare animals off the hedge before starting to cut in order to prevent them from
being injured.
• Provide for a safe and cleaned workplace. Remove from the working area objects
which might be thrown off.
• Avoid abnormal posture. Keep your balance at all times. Do not work with the
upper part of the body leaned forward.
• Operate the hedge trimmer only with safe standing position.
• Stop the hedge trimmer when moving to another work place.
• Keep hands and feet away from the cutting device when it moves.
• Hold the hedge trimmer so that you do not inhale exhaust gases. Do not work in
closed rooms.
• Do not use the hedge trimmer to pick up or remove wood pieces or other objects.
• Remove unconditionally any foreign objects out of the hedge (e.g. wires) as these
can damage the knives of the hedge trimmer.
• Hold the hedge trimmer always rmly with both hands, left hand on the front
handhold and right hand on the rear handhold.
• The device will run for a short period after throttle trigger is released (free wheel-
ing effect).
• Start trimming with the cutting device moving.
• Never touch the cutting device with your hands during operation.
• Never work
- with stretched arms
- on hardly accessible places
- too far bent forward
• Never work with the hedge trimmer above shoulder height.
• Never allow the running cutting device to contact metallic fences or the ground.
• Stop the engine and pull the spark plug connector:
- when you notice changes in the device’s behaviour,
- to remove jammed material,
- to check the cutting device after it had contact with stones, nails or other hard
objects,
- to eliminate faults,
- for work breaks,
- before leaving the hedge trimmer.
AUS
HTH250/240P Working instructions
AFTER SALES SUPPORT 21
 1300 855 831  [e-mail]
MODEL: HTH250/240P PRODUCT CODE: 59823 03/2018

Layout/Scope of delivery HTW250/240P
10 AFTER SALES SUPPORT
 [e-mail]  00800 4003 4003
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
• Do not place a hot hedge trimmer in dry grass or onto inammable objects.
• Before starting your work make sure that:
- no other persons or animals stay within the working area,
- you can always step back without any barriers,
- your standing area is free from foreign objects, brushwood and branches,
- you have always a secure standing position.
If persons who have blood circulation problems are too often exposed to vibrations
damages to the nervous system or to blood vessels may occur.
You can reduce vibrations
• by thick and warm working gloves,
• shorter working time (have longer breaks).
See a doctor if your ngers swell, you don’t feel well or your ngers become numb.
Working with the hedge trimmer
Hold the hedge trimmer with both hands on a safe distance from the body.
• The maximal diameter to cut depends on the wood’s type, age, moisture and
hardness.
• Therefore cut very thick branches using branch shears to your desired length
before trimming the hedge.
• Due to its double sided knives the hedge trimmer can be guided forward and
backward or by oscillating movements from one to another side.
• At rst cut the sides of the hedge and then the upper edge.
• Cut the hedge from the bottom up.
• Cut the hedge in trapezium shape.
• Stretch a guide over the complete length of the hedge when you want to shorten
the upper edge of the hedge evenly.
• Trim in several passes if you have to cut down a large portion of the hedge.
Best time for hedge trimming:
• Leaved hedge: June and October
• Conifer hedge: April and August
• Quickly growing hedge: from May and then every 6 weeks
Pay attention to breeding birds in the hedge. If so, put off hedge trimming or leave
this area out.
AUS
Working instructions HTH250/240P
22 AFTER SALES SUPPORT
 [e-mail]  1300 855 831
MODEL:HTH250/240P PRODUCT CODE: 59823 03/2018

HTW250/240P Introduction
AFTER SALES SUPPORT 9
 00800 4003 4003  [e-mail]
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
At all times pay attention to all safety instructions.
IX. MAINTENANCE, CLEANING AND SERVICING
Before each maintenance and cleaning work
- Stop the engine.
- Wait until the cutting device stops moving.
- Stop the engine and pull off the spark plug connector (with the exception of idle
speed adjustment).
Do not carry out maintenance work close to open ames. Risk of re.
Maintenance and repair work other than those described in this chapter is only
allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must unconditionally
be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected damages and injuries.
In order to aviod possible injuries wear gloves.
To guarantee a long and reliable usage of the hedge trimmer carry out the following
maintainance works regularly.
Check the hedge trimmer for obvious defects such as
- loose fastening elements
- worn or damaged components
- deformed, broken or damaged cutting device
- leaks from the fuel tank cap or fuel lines
Check the hedge trimmer after each application for
- wear and tear, in particular sliding play of the cutting device
- correct assembly and faultless covers and protective devices.
Necessary repair or maintainance operations have to be carried out before the
usage of the hedge trimmer.
Adjusting the cutting device (Fig. 3)
Readjust the sliding play if cut material is clamped between the blades or the play
AUS
HTH250/240P Working instructions/Maintenance, cleaning and servicing
AFTER SALES SUPPORT 23
 1300 855 831  [e-mail]
MODEL: HTH250/240P PRODUCT CODE: 59823 03/2018

Layout/Scope of delivery HTW250/240P
10 AFTER SALES SUPPORT
 [e-mail]  00800 4003 4003
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
has increased due to normal wearing of the cutting device after a longer period of
use.
To obtain good cutting results the free motion between the blades and the sword
must be correctly adjusted.
For this proceed as follows:
1. Loosen the nuts (A) on the top surface of the cutting device with the open end
wrench (16).
2. Slightly tighten the screws (B) on the underside with the allen key 4mm (17) (if
required loosen them previously).
3. Turn the screw (B) back anticlockwise by a quarter up to a half turn.
4. Use the allen key 4mm (17) to hold the screw (B) and rmly tighten the nuts.
The sliding play is correctly adjusted if the washer under the screw head can
just be freely moved back and forth by hand.
5. Lubricate the cutting device using environmental-compatible lubricating oil.
If the play is too small, this may cause a great extent of heating and thus damage to
the device.
Lubricating the gearbox (Fig. 1)
Lubricate the gearbox every 10 to 20 operating hours.
1. Put the grease gun onto the zerk tting (10).
2. Force some grease into the zerk tting (10).
Adjusting the idle speed (Fig. 4)
If the cutting device continues to run while the engine idles, you have to correct the
idle speed.
1. Allow the engine to run warm for 3-5 minutes (no high speed).
2. Turn the adjusting screw (C):
Clockwise
- idle speed increases (+)
Counterclockwise
- idle speed decreases (–)
Contact the manufacturer if the cutting device still continues to run in idle mode.
Do not continue working with the hedge trimmer in such a condition.
AUS
Maintenance, cleaning and servicing HTH250/240P
24 AFTER SALES SUPPORT
 [e-mail]  1300 855 831
MODEL:HTH250/240P PRODUCT CODE: 59823 03/2018

HTW250/240P Introduction
AFTER SALES SUPPORT 9
 00800 4003 4003  [e-mail]
MODEL: HTW250/240P PRODUCT CODE: 64055 xx/2017
Cleaning / replacing the air lter (Fig. 5&6)
Clean the air lter from dust and dirt on a regular basis to prevent
- starting problems,
- loss of output,
- too high fuel consumption.
Clean the air lter every 8 operating hours, or more frequently in dusty environ-
ments.
1. Put the choke (4) to ‘cold start’ to prevent dirt particles from coming into the
carburettor.
2. Remove the air lter cover (8) by turning the wing screw (9) anticlockwise.
3. Remove the air lter (D).
4. Wash the air lter in a luke warm soapy solution. Do not blow out dirt particles,
otherwise there is a risk of eye injury.
5. Clean the air lter interior using a brush.
6. Allow the air lter to dry well and reinsert it.
7. Re-mount the air lter cover (8).
Replace the air lter on a regular basis.
Damaged air lters must be replaced without delay.
Cleaning/replacing the fuel lter (Fig. 7)
Check the fuel lter (E) if required. A contaminated fuel lter restricts the fuel supply.
Open the tank cap (12) and pull the fuel lter through the opening using a wire hook.
• Slight contamination:
- Pull the fuel lter (E) from the fuel line and clean it in petroleum ether.
• Bad contamination:
- Replace the fuel lter (E).
Checking / replacing the spark plug (Fig. 8)
Do not touch the spark plug (F) or the spark plug connector (21) when the engine
runs. High voltage!
Risk of burning on the hot engine. Wear protective gloves.
Check the spark plug and the spark gap on a regular basis. (Fig. 8)
For this proceed as follows:
1. Pull the spark plug connector (21) from the spark plug (F).
AUS
HTH250/240P Maintenance, cleaning and servicing
AFTER SALES SUPPORT 25
 1300 855 831  [e-mail]
MODEL: HTH250/240P PRODUCT CODE: 59823 03/2018