Gardner Bender SP-7 User manual

REPAIR PARTS SHEET
Stud Punch
GARDNER BENDER is not RESPONSIBLE FOR DAMAGE OR INJURY CAUSED BY UNSAFE USE, MAINTENANCE OR
THE APPLICATION OF ITS PRODUCTS. Please contact Gardner Bender for guidance when you are in doubt as to the
proper safety precautions to be taken in designing and setting up your particular application.
SP-7
Punches 111⁄32" holes for ½" to 1" conduit
or pipe in aluminum and mild steel studs
Read & understand this instruction book completely
before operating product. Failure to understand safe
operation of this tool can cause injury.
!CAUTION
www.gardnerbender.com
PO Box 3241 Milwaukee, WI 53201-3241 | 414.352.4160 | fax [phone]
6615 Ordan Drive | Mississauga, Ontario L5t 1x2 | 905.564.5749 | fax [phone]
RPS-0153 | January 2007
www.gardnerbender.com
PO Box 3241 Milwaukee, WI 53201-3241 | 414.352.4160 | fax [phone]
6615 Ordan Drive | Mississauga, Ontario L5t 1x2 | 905.564.5749 | fax [phone]
RPS-0153 | February 2007
IMPORTANT: RECEIVING INSTRUCTIONS
Visually inspect all components for shipping damage. If you find damage, notify the carrier at once. Shipping damage is NOT covered by warranty.
The carrier is responsible for all repair or replacement costs resulting from damage in shipment.
STUD PUNCH ACCESSORIES
Patented One-Piece Design
Exclusively from Gardner Bender, new SnapSHOT™ Universal Stud Insulators provide
code mandated* 360° protection for cable runs through increasingly poplar metal
studs, where sharp hole edges could otherwise gouge plastic or rubber-jacketed
electric, communications or network cable. The patented one-piece design and folding
tabs make installation literally a snap, resulting in a tight and secure attachment
to the stud. The smooth, hang-free surface eases pulls, while the high-density
SnapSHOT™ design accommodates any shape pre-punched hole or standard 1¹¹/³²"
field-punched holes.
*Meets requirements of NEC Article 300-4(b) and CEC Rule 12-516.
Code-compliant protection for NM Cable in
both factory and field punched metal studs.
Part # Description Pkg Qty
SI-25 Metal Stud Insulator Bag 25
SI-100 Metal Stud Insulator Bag 100
REPAIR AND SERVICE INSTRUCTIONS: For repair service and parts contact your nearest Gardner Bender Service Center.
The Gardner Bender Service Center will provide complete and prompt service on all Gardner Bender products.
PARTS AND SERVICE: For quality workmanship and genuine Gardner Bender parts, select an Authorized GB Service Center for your repair needs.
Only repairs performed by an Authorized Service Center displaying the official GB Authorized sign are backed with full
factory warranty. Contact Gardner Bender [phone] for the name of the nearest GB Authorized Service Center.
WARRANTY: Gardner Bender warrants its product against defects in workmanship and materials for 1 year from date of delivery to user.
Warranty does not cover ordinary wear and tear, abuse, misuse, overloading, altered products or use of improper fluid.
WARRANTY RETURN PROCEDURE: When question of warranty claim arises, send the unit to the nearest GB Authorized Service Center for inspection, transportation
prepaid. Furnish evidence of purchase date. If the claim comes under the terms of our warranty the Authorized Service Center
will REPAIR OR REPLACE PARTS AFFECTED and return the unit prepaid.
Feature Comparison
Fits factory punched holes/standard holes •• • •
Easy to install design •
One-piece installation •
UL approved •• •
Arlington
Greenlee
Caddy

A For removal of punch, cap screw must be extracted. Once cap screw
has been withdrawn, swing handle out of the way and lift punch straight out.
Reverse the above operation for installation of punch.
B To Replace die, remove set screw (one closest to die). Lift die straight up and out.
To install die reverse the above operation.
B
A
Set Screw
Cap Screw
REPLACEMENT OPTIONS REPLACEMENT OPTIONS
Service Parts Kit breakdowns shown here.
5
1
2
3
4
8
11
9
7
10
6
Kit # Comp. # Description Qty
SP7SSK Replacement Spring & Sleeve Kit
1 Bushing 1
2 Washer 2
3 Split Washer 1
4 Spring 1
SP7PDK Replacement Punch Die Kit
5 Die 1
6 Set Screw 2
SP7PLK Replacement Pivot Link Kit
7 Bolt (HHCS) M6-57 1
8 Bolt (HHCS) M6-45 2
9 Lock-Nut-M6 3
10 Pivot-Link 1
SP7PK Replacement Punch Kit
11 Punch 1
8 Bolt (HHCS) M6-45 2
9 Lock-Nut-M6 2
Note: Components items sold in kits only and not sold separately.
APPLICATION
A
B