Garmin GTS 8000 User manual

1
Version 1.0
Replacing GTS 8000 on Citation M2
Garmin G3000 Software Version 10
Caution: Before starting the software or configuration loading process, certain
items may be required to be recorded first, to prevent loss of
information or settings. See Section 1 for details.
Caution: Make certain that all SD cards are available before starting. These are
usually located in a blue pouch onboard the aircraft (usually in AFM).
Caution: Follow all steps in a given section for specific loadings. Failure to do so
will result in probable rework.
Caution: Ensure that power is available through a GPU so that power is not
interrupted during the loading process.
Note: This document is to supplement, not replace, the Cessna Citation M2
MM, and Garmin G3000 LMM.
Note: Reference latest revision of the Garmin G3000 LMM 190-01668-00.
Table of Contents
Introduction G3000 System Familiarization
Section 1 References Prior to Certain Software and Configuration Loading
Section 2 Software and Configuration Loading
Section 3 Aircraft Configuration
Section 4 Final Verification / Return to Service
Section 5 Troubleshooting
Appendix A Determining Options Installed
Appendix B Configuration ID / CRC Numbers

2
Version 1.0
Introduction G3000 System Familiarization
When in configuration mode, select GDU controls on left side of GTC 1. Ensure that PFD 1 is
selected on the screen. The dual concentric knobs on the lower right bezel will be utilized, and
throughout this document will be referred to as the FMS small and large knob. The Enter
button will be in the lower right part of the screen.
As an alternative, you can use the dual concentric knobs (labeled PFD) and Enter button on the
GCU-275 controller mounted above PFD 1.

3
Version 1.0
Section 1 References Prior to Certain Software and Configuration Loading
When replacing the GTS 8000 the following steps must be completed first:
Note: This is with the G3000 powered up in normal mode.
Radar Trim Settings
•Go into the left GTC:
oUse Back button and select Aircraft Systems.
oSelect Maintenance.
oEnter CACCDMS for password.
oSelect Radar Trim.
Record Pitch Trim Value= ____________
Record Roll Trim Value= ____________
oIf the Radar trims were not both at zero originally:
Select Restore Defaults.
oSelect Home.
Select Utilities.
Select Setup.
Select Avionics Status.
Select the Airframe Tab on the left side.
Record the Config ID now that the radar trims are zero= ____________
•This is for reference in case it is needed later.

4
Version 1.0
Section 2 Software and Configuration Loading
This section will provide the steps necessary to target load the software and configuration into
GTS 8000 after replacement.
Note: Anytime that software or configurations are being loaded, all three displays, and both
touch controllers must be in configuration mode.
Note: Ensure that you have completed the steps contained in Section 1.
•GTS 8000 (TCAS I or TCAS II Processor)
Note that TCAS II functions are through an unlock card. See section 4.
•When the GTS 8000 is replaced, then software and configuration loading is required.
1) Pull the following circuit breakers:
L PFD
MFD
R PFD
L Touch Control
R Touch Control
2) Insert the 010-01121-10 software loader card into the upper slot of PFD 1.
3) Turn on aircraft power.
4) Press and hold the right knob on the left GTC and push the L Touch Control circuit
breaker in.

5
Version 1.0
Let go when you see initializing.
5) Press and hold the right knob on the right GTC and push the R Touch Control
circuit breaker in.
Let go when you see initializing.
6) Press and hold the #12 softkey on the #2 PFD and push the R PFD circuit breaker
in.
Let go when you see initializing.
PFD 2 should come up in configuration mode.
•SYSTEM STATUS should show at the top of the screen.
7) Press and hold the #12 softkey on the MFD and push the MFD circuit breaker in.
Let go when you see initializing.
MFD should come up in configuration mode.
•SYSTEM STATUS should show at the top of the screen.
8) Press and hold the #12 softkey on the #1 PFD and turn on power.
Let go when you see initializing.
9) Press the NO softkey at “DO YOU WANT TO UPDATE SYSTEM FILES?” prompt.
10) Press the NO softkey at “DO YOU WANT TO UPDATE THE CUSTOM GRAPHICS
FILES (EG, SPLASH SCREEN)?” if it appears.
11) PFD 1 should come up in configuration mode.
SYSTEM UPLOAD should show at the top of the screen.
Clearing Maintenance Log
Note: The maintenance log must be cleared before loading the configuration.
•On the left GTC 570 touch controller:
1) Select GDU Controls.
2) Select MFD on the left side of the screen under GDU block.
•Rotate the small FMS knob to select the MAINTENANCE LOG on the page.
•Press the Clear softkey on the MFD.
1) The ‘Erase entire Maintenance Log?’ prompt will appear.

6
Version 1.0
2) Press Enter.
•Wait until “Clearing Log…” disappears before continuing.
•Select PFD 1 on the GTC 570 to switch the display being controlled.
Loading Software & Configuration
1) Activate the cursor by pushing down on the FMS knob.
2) Rotate the small knob to drop the menu down, and highlight ‘525 Base
Configuration’ in the GROUP field.
3) Press the Enter key.
4) Rotate the small knob to drop the menu down, and highlight ‘Cessna Model 525
Base Configuration’ in the ITEM field.
5) Press the Enter key.
6) Select the CLR ALL softkey at the bottom of the display.
7) Using the FMS knob, highlight the following, press Enter for each, which will place
a check mark in each box:
GTS8000 Software
GTS8000 Configuration
GTS8000 Audio Software
8) Select the LOAD softkey at the bottom of the display.
9) A green PASS message is shown beside software and configuration items as they
are successfully completed.
10) Acknowledge when ‘Upload and Crossfill Complete’ is displayed by pressing the
Enter key.
11) Push the UPDT CFG softkey to update the system configuration files.
12) After the software and configuration files are loaded, pull the L PFD circuit
breaker, and remove the 010-01121-10 software loader card from PFD 1.

7
Version 1.0
Section 3 Aircraft Configuration
Aircraft Configuration
•Place the G3000 back in configuration by pressing and hold the #12 softkey on the PFD 1
and pushing in the L PFD circuit breaker. Let go when you see initializing.
•Transponder and TCAS Configuration:
oRotate the inner right knob to go to the Aircraft Configuration page.
oPush the FMS knob to activate it.
oThe cursor should be on the Aircraft Registration line. Rotating the small FMS
knob provides a single character cursor. Use the small knob to change the value,
and the large knob to move to the next character.
U.S. registered aircraft:
•Enter the aircraft tail number using the FMS knob to select
characters.
•The VFR code should be set to 1200.
•Press Enter.
Foreign registered aircraft:
•Note that the Hexadecimal code will need to be entered first.
•Then the tail number should be entered.
•Also the VFR code will need to be set to the correct value for the
country of registry.
•Press Enter.
Select the softkey labeled SET GTX1 to program #1 GTX-3000. Select OK to
acknowledge.
Select the softkey labeled SET GTX2 to program #2 GTX-3000. Select OK to
acknowledge.
Select the softkey labeled SET GTS to program the GTS-8000. Select OK to
acknowledge.

8
Version 1.0
Section 4 Final Verification / Return to Service
Note: This is with the G3000 powered up in normal mode.
•Determine options installed using Appendix A.
•Select Home on the left GTC controller.
oSelect Utilities.
oSelect Setup.
oSelect Avionics Status.
oSelect the Airframe tab on the left side.
oVerify that the configuration ID (CRC Number) matches the number determined in
Appendix B based on the options installed in the aircraft.
oSelect the LRU Info tab on the left side.
Verify that all the LRUs are showing green check mark.
oSelect the MSG button:
Verify there is no DB Mismatch message present.
Verify there is no Manifest message present.
Verify there is no Config message present.
•If the initial radar trims were not zero:
oSelect Home on the left GTC controller.
oSelect Aircraft Systems.
oSelect Maintenance.
oEnter password CACCDMS.
oSelect Radar Trim.
Enter the Pitch and Roll trims recorded in section 1.
Return to Service Testing
•For testing, complete section 7.17.1 in the Garmin G3000 LMM.

9
Version 1.0
Section 5 Troubleshooting
This section will provide corrective actions for issues seen after the software is loaded.
Substitute LRU name for ***.
•*** DB Error or *** DB Mismatch
oEnsure that the supplemental SD cards are installed in the lower slots of the
displays.
oDatabases do not match.
oVerify which database is not the same, and reload as necessary.
•*** Manifest Error
oSoftware does not match what the system is expecting.
oCheck work performed and reload necessary software again.
•*** Config
oConfigurations do not match what the system is expecting.
oCheck work performed and reload necessary configurations again.

10
Version 1.0
Appendix A Determining Options Installed
Note: This is with the G3000 powered up in normal mode.
Caution: If any optional radio appears to have an amber X and is grayed out as in this
example, then the LRU is not installed, but was previously loaded incorrectly.
Determine Options Installed
•Single GSR56
oOn either GTC 570, select the SERVICES / TELEPHONE button, then select
Telephone. A single Iridium transceiver is displayed on the left side.
•Dual GSR56
oOn either GTC 570, select the SERVICES / TELEPHONE button, then select
Telephone. A double Iridium transceiver is displayed on the left & right side.
•GDL69
oFrom the Home screen of either GTC 570, touch the Weather button. Then touch
Weather Selection. The option is installed if Sirius XM Settings is displayed.