Garrett Pro-Pointer AT 1140900 User manual

®

2

(Reverse side of pinpointer)
FEATURES
ON/OFF, Retune, Adjust Button
Pinpointing Tip
360° Side-Scan Area
Exclusive Scraping Blade
LED Flashlight
Waterproof Speaker
Lanyard Attachment Loop
Sealed Battery Cover
Ruler in Inches and Centimeters









3
Powering On
Press and release the button () while holding the detector away from any
metallic objects. You will hear 2 beeps and the LED () will remain on.
Powering Off
Press and hold the button for a half second until you hear a single beep (or
single vibration in Silent Mode), indicating power down.
Changing Settings
The Pro-Pointer AT has three Sensitivity settings and two detection settings:
Audio-plus-Vibrate orVibrate-only (silent).
To enter adjustment mode, press and hold the button () for 2
seconds—indicated by a single beep followed by a dual-tone beep and
flashing LED. (Note: In Silent Mode, beeps are replaced by vibration pulses.)
The first button press after entering adjustment mode indicates the current
setting. Repeatedly press the button to cycle through the 6 settings:
1 beep = minimum Sensitivity, with audio
2 beeps = medium Sensitivity, with audio (Default setting)
3 beeps = maximum Sensitivity, with audio
1 vibrate = minimum Sensitivity/Silent
2 vibrate = medium Sensitivity/Silent
3 vibrate = maximum Sensitivity/Silent
To exit adjustment mode, press and hold the button for 2 seconds—
indicated by a dual-tone beep (dual vibrate in Silent Mode), or wait 5 seconds
for automatic exit.

4
Fast Retune feature quickly
tunes out mineralized ground,
saltwater, wet sand, and other
challenging environments.
Notes:
• Lower Sensitivity settings are recommended to prevent detection of
highly mineralized grounds.
• Detection remains operable during the adjustment mode.
• Settings will be remembered when the unit is switched off and back on.
Fast Retune for Mineralized Ground
To tune out the detection of saltwater, wet sand or highly mineralized
ground, hold the tip of the Pro-Pointer AT to the water, sand or soil and
quick-press the button () for an instant Retune.
If necessary, repeat this Fast Retune to further eliminate any
environmental response. Note: An alternate means of eliminating the
ground response is to reduce Sensitivity.
Precisely Pinpointing Large Targets
Slowly scan toward the object until the response increases to full/constant
alarm. Then quick-press the button to instantly retune and narrow the
detection field. Continue scanning toward the object to find its precise
location. Repeat this Fast Retune to further narrow detection field as needed.

5
Lost Pinpointer Alarm
After 5 minutes of being ON without a button press, the Pro-Pointer AT
will begin emitting progressively faster warning chirps for 60 minutes.
Press the power button to reset.
Auto-Off Feature
After one hour of warning chirps, the Pro-Pointer AT will power off
automatically.
Scraping Blade
This rugged edge is ideal for sifting through dirt while searching for the
target.The Pro-Pointer AT’s 360º-side-scan detection allows the detector
to alarm when the blade is passed in close proximity to a metallic target.
Lanyard Attachment Clip
Use to attach the Pro-Pointer AT to your belt, digging pouch or your
detector (if desired).
Holster
Secure to any standard size belt. A metal snap within the holster will
cause the pinpointer to alarm if put away while powered on.

6
Ruler
The Pro-Pointer AT has a ruler molded into its exterior to measure a
target’s depth in either centimeters or inches.
Low Battery Alarm
When the battery becomes low, the detector will sound an alternating
dual-tone alarm. Replace the 9V battery as soon as possible.
Battery Replacement
Simply rotate the battery cover counterclockwise to remove and
clockwise to tighten by hand. To properly install the 9V battery, match
the larger battery terminal to the larger opening in the compartment.
Remove the battery when the unit is to be stored more than 30 days.
Operational Information and Tips
• Operation is completely automatic. All metals will be detected
including ferrous and non-ferrous.
• When a target is detected, the Pro-Pointer AT will produce
an audio and/or vibration alert. The rate of the pulsing audio and
vibrations increase proportionately as the pinpointer is moved closer
to a metallic target.
• Maximum detection of very small targets is obtained against the side
about ½”from the tip.
• Toavoidcancellingoutatarget,donotturnonthePro-PointerAT while
it is adjacent to the target.

7
• Because the Pro-Pointer AT is a static, non-motion detector, optimum
operation is achieved when the unit is switched off between uses.
• Avoid using the Pro-Pointer AT as a digging or prying tool. It is designed
for flat side-scanning and precise pinpointing with its tip. It is not
intended to be used with excessive force.
• For water use, do not exceed 10 feet (3 meters) depth. Make sure the
battery cap threads are free of sand, sediment, etc. and that O-ring is
periodically lubricated with silicone grease to maintain a tight seal.
• To remove dried dirt, mud or other debris from the unit, simply hand
wash it with soap, water, and a soft cloth. Do not use any type of
abrasive or chemical cleaners which could scratch or erode its surface.

The Garrett Pro-Pointer AT is manufactured in the United States of
America and in accordance with Garrett’s ISO 9001 internationally
certified Quality Management System and meets the following
international standards:
• FCC • CE • RoHS • ICNIRP • IEC 529-IP 68
SPECIFICATIONS
Model Name: Garrett Pro-Pointer®AT
Model Number: 1140900
Operating Temperatures: -35ºF (-37ºC) to 158ºF (70ºC)
Operating Frequency: 11.5 kHz
Waterproof Rating: 10 foot (3 meter) maximum depth; IP 68
Tuning: Automatic or manual retune
Indicators: Proportional audio/vibration pulse rate
Controls: Power, Retune, Adjust switch
Dimensions: Length: 9” (22.9 cm)
Thickness: 1.5” (3.8 cm) tapered to
.875” (2.2 cm)
Weight: 6.5 oz. (0.2 kg.), with battery in
Battery: Single 9V (included)
Battery Life: Carbon: 16 hours
Alkaline: 30 hours
Rechargeable: 8 hours
Warranty: 2 Years, Limited Parts/Labor
Patent Information: US 7,575,065; D583,261 and
patents pending
Garrett Metal Detectors, garrett.com and PRO-POINTER AT are
trademarks and registered trademarks of Garrett Electronics
Inc. © 2015 Garrett Metal Detectors. 1538800.C.1015
MADE IN
THE USA