Gatekeeper Y35HD User manual

Y35HD QUICK INSTALL GUIDE
- Page 1 -
Y35HD QUICK INSTALL GUIDE
MOUNTING
§ Mount the Y35HD in the vehicle's cabin area where there is environmental control (i.e.
heating and/or air-conditioning).
§ Secure the Y35HD to interior surfaces using the Tek Screws provided for mounting.
§ All cables running through holes in sheet metal (ceiling, bulkhead, etc.) must be
protected with grommets.
§ Ensure that the device is mounted where it is not easily accessible by non-authorized
personnel.
§ DO NOT orient the device such that the drive caddy handle faces the floor of the
vehicle.
§ DO NOT disassemble the device. There are no user serviceable parts inside, and
removing the cover of the Y35HD will void the device's warranty.
POWER SUPPLY
§ The Y35HD operates between 8V ~ 36V. Please ensure a regulated, consistent power
source is available for the device.
§ The power supply cable connects to the back of the device through a 9-pin power
input-output connector (CAB000360). The power source should be clean and
(preferably) connected directly from the battery or the power bus.
§ The supplied fuses MUST be used; Failure to use the provided fuses will void the
device's warranty.
§ The 3AMP fuse must be installed close to the power source on the Yellow Ignition wire
on CAB000360
§ The 15AMP fuse must be installed as close as possible to the source on the Red (+12V)
wire on CAB000360
SENSOR CONNECTIONS
§ GPS Connection - The device is equipped with a connection port for an external GPS
antenna. The GPS must be connected in order to embed vehicle location and vehicle
speed information with the video. The GPS antenna should be installed on the exterior
roof of the vehicle with a clear view of the sky
§ ICD Connection – The 10-pin ICD connector (CAB000390 + CAB000391) is used to
connect the ICD to provide a touch-screen interface.
§ Driver Alert Button Connection - The tri-color Driver Alert Button (G4-TCR-DrvAlert) is
connected using the 4-Pin connector (CAB000371) to the RS485 Converter
(CAB000387) to the sensor cable (CAB000376)
§ External Sensor Module Connection - The ESM is connected to the Sensor Cable
(CAB000387) to provide support for an additional 8 sensor inputs (9 – 16), and 2
sensor outputs.
CAB000376
Sensor Wire and Color
Sensor
OSD Name
SENSOR_IN1 (Yellow)
Brake
BK
SENSOR_IN2 (Orange)
Warning Lights
WN
SENSOR_IN3 (Black)
Stop Arm
SA
SENSOR_IN4 (White)
Door
DR
SENSOR_IN5 (Blue)
Left Turn
LT
SENSOR_IN6 (Red)
Right Turn
RT
SENSOR_IN7 (Green)
Extra1
EX1
SENSOR_IN8 (Brown)
Extra2
EX2

Y35HD QUICK INSTALL GUIDE
- Page 2 -
CONFIGURATION
§ Y35HD configuration menus (when using the ICD, Finger Mouse, or IR Remote control
interfaces) are accessed from:
o Main Menu èSetup / Config
§ When connecting wirelessly through the Android compatible G4 Connect™ app.,
configuration menus are accessed from:
o Preferences è Config
§ Enter the following login information when prompted:
o User ID: admin
o Password: admin
§ After setting the configurations, with the HDD inserted access the setup menu.
Navigate to Setup>Maintenance>Storage to format the HDD.
§ Start vehicle, and wait for recorder to boot up (approximately two minutes). Confirm
live camera video is visible on monitor (small Green camera in each camera image –
indicates the DVR is recording).
§ Confirm DVR is recording by observing the LED’s as per the following table
§ To access the HDD, turn the key to the unlocked position, flip the HDD handle down,
wait for the LEDs to turn off and pull the HDD caddy out.
Record Mode
Safe to SD Card Mode
LED
Color
Flashing
Status
LED
Color
Flashing
Status
PWR (Power)
Blue
Constant On
PWR (Power)
Blue
Off
USB (If USB Drive
Connected)
Blue
On
USB (If USB
Drive
Connected)
Blue
Off
ALM (Alarm)
Red
Off
ALM (Alarm)
Red
Off
REC (Recording)
Green
Constant On
REC (Recording)
Green
Off
ERR (Hardware Error)
Red
Off
ERR (Hardware
Error)
Red
Off
NET (If a network is
connected)
Green
Constant On
NET (If a
network is
connected)
Green
Off
CABLING DIAGRAM