GBC Shredmaster 5570X Manual

0
IMPORTANT
To quickly and easily confirm your warranty, register your new
shredder online at www.gbc.com
IMPORTANTE
Para confirmar su garantía rápida y fácilmente,
registre su nueva trituradora en línea en www.gbc.com
IMPORTANT
Pour confirmer votre garantie rapidement et facilement, enregistrez votre
nouveau déchiqueteur en ligne à www.gbc.com
Shredders
3890D
3870M
5570X
6550X
4500S
5500S
6500S
Operating Procedures 2
Procedimientos de funcionamiento 8
Procédure d'exploitation 14
F
E
3890 shredder 3/14/05 10:09 AM Page 21

IMPORTANT SAFETY INSTRUCTIONS
Your safety as well as the safety of others is important to GBC. In this instruction manual and
on the product are important safety messages. Read these messages carefully.
The safety alert symbol precedes each safety message in this instruction manual and on
the product. This symbol indicates a potential personal safety hazard that could hurt you
or others, as well as cause product or property damage. Do not connect this unit to electrical
power or attempt to operate it before you have read these operating instructions. Save these
instructions for later use.
The following warning is found on the bottom of the product:
The following ISO and IEC symbols appear on this product, and their meanings are as follows:
Means shredder is in standby mode and power is on.
Means OFF
The symbols which become illuminated are:
022
Means Power ON/Standby
Means Power OFF
Means the shred bin is full
Means the cabinet door is open
This safety message means that you could be seriously
hurt or killed if you open the product and expose
yourself to hazardous voltage.
This safety message means that you could be
seriously hurt if you place your hands in the
discharge area.
!
The following warning is found inside of the cabinet door:
3890 shredder 3/14/05 10:09 AM Page 2

IMPORTANT SAFETY INSTRUCTIONS
This means you should be careful because long hair can become entangled in the
cutting head. This could hurt you.
This means don’t reach into the feed opening of the cutting head. This could hurt you.
This means be careful of ties and other loose clothing which could become entangled
in the cutting head. This could hurt you.
This means you should be careful of loose jewelry which could become entangled in
the cutting head. This could hurt you.
This means do not allow children to use the shredder.
ELECTRICAL SAFEGUARDS
•Unplug your shredder before moving it, emptying the bag, or when it is not in use for an
extended period of time.
•Do not operate with a damaged power supply cord or plug, after it malfunctions, or after it
has been damaged in any manner.
•Do not overload electrical outlets beyond capacity as this can result in fire or electrical
shock.
•The socket-outlet should be installed near the equipment and shall be easily accessible.
•Do not alter attachment plug. Plug configured for the appropriate electrical supply.
•Do not use near water.
•Keep out of the reach of children.
•Do not use extension cords to connect this product to the power supply.
SERVICE
Do not attempt to service or repair the unit yourself. If your shredder should require service,
contact your local dealer or call GBC National Service at 800-790-7787. Please have the model
and serial number of your shredder ready when calling.
03
3890 shredder 3/14/05 10:09 AM Page 3

04
SET UP
Caution! Shredders are heavy equipment (see
“Total Unit Weight” in the “Specifications”
section of this Manual). To insure proper
installation and avoid injury, GBC recommends that
two people set up this unit.
FIGURE 1. Begin by opening the cabinet door by
pulling the handle. Place the shredder head onto
the top of the cabinet as illustrated.
FIGURE 2. Insert the enclosed plastic bag in the
pull-out waste receptacle. First, pull out the waste
receptacle (1) and remove the red round belt (2).
Turn over the top of the bag several times (3),
insert the plastic bag in the waste receptacle and
fasten with the round belt (4). Push the waste
receptacle into the cabinet and close the cabinet
door (5).
FIGURE 1
FIGURE 2
!
1
2
3
4
5
3890 shredder 3/14/05 10:09 AM Page 4

OPERATION
POWER ON
FIGURE 3. Press the button to Power On. The
green light will illuminate when ready to operate.
You are now ready to shred!
NOTE: This shredder is for paper shredding
only. Due to the sensitive cutting mechanism
you cannot shred staples, paperclips, PVC etc.
(Applies to Model 3890D only).
To shred simply insert paper into the throat of the
unit. Once your document has activated the automatic
on feature, the unit automatically will start and then
will stop once your document is shredded.
CD/DVD
To destroy a compact disc or dvd (straight-cut
models only), insert the media into the center of the
throat area. Once your media has activated the
automatic on switch, the unit will start and then will
stop once your media is shredded.
BIN FULL
FIGURE 4. In order to prevent shreds from backing
up into the cutters and jamming your shredder, this
unit features an automatic bin full shut off. Once the
shred bin is full, the unit will shut off automatically
and the bin full light (E) will illuminate. You can now
compact the shreds and continue shredding, or empty
the shred bin.
Note: For safety reasons, whenever the cabinet door
has been opened this unit will not operate until the
door is closed and the unit is turned off and then back
on.
DOOR AJAR
Your shredder is equipped with a safety interlock
which will not allow the unit to operate if the cabinet
door is open. The Door Ajar light (D) will illuminate if
the cabinet door is not fully closed.
OVERLOAD (Reverse)
If too much paper is inserted into the throat of the
unit, the shredder will sense an overload and reverse
automatically to avoid unnecessary motor heating. To
clear the overload, switch the unit to Reverse mode
until the paper is clear of the throat area. You can now
separate your pages into smaller sets and continue to
shred.
05
FIGURE 3
FIGURE 4
On/Forward
Reverse
Bin
Full
Door Ajar
Off
On Light
F
E
D
3890 shredder 3/14/05 10:09 AM Page 5

06
Model 3870M 3890D 4500S 5500S 6500S
GBC Part No. 1757320 1757330 1757340 1757360 1757400
Throat Width 10" 10" 12" 15" 16"
Shred Size 3/32" x 19/32" .8mm x 5mm 1/4" 1/4" 1/4"
Sheet Capacity 8 - 10 6 - 7 20 - 22 20 - 22 28 - 30
Speed/FPM 25 22 30 40 25
Basket Capacity 30 Gallon 30 Gallon 36 Gallon 42 Gallon 55 Gallon
Amperage 8A 8A 8A 8A 11.6A
Volts/Hz 120V/60Hz 120V/60Hz 120V/60Hz 120V/60Hz 120V/60Hz
Model 4550X 5550X 5570M 6550X
GBC Part No. 1757350 1757370 1757380 1757410
Throat Width 12" 15" 15" 16"
Shred Size 5/32" x 1-1/2" 5/32" x 1-1/2" 3/32" x 19/32" 3/16" x 2-3/8"
Sheet Capacity 16 - 18 15 - 16 10 - 11 23 - 25
Speed/FPM 30 35 35 25
Basket Capacity 36 Gallon 42 Gallon 42 Gallon 55 Gallon
Amperage 8A 8A 8A 11.6A
Volts/Hz 120V/60Hz 120V/60Hz 120V/60Hz 120V/60Hz
OPERATION (cont'd)
SHIELD
FIGURE 5. A shield is provided for your added
protection. Should you need to clear debris or
access the photo sensor as described in Figure 7,
simply push on the top of the shield to allow
access.
FIGURE 5
SPECIFICATIONS
3890 shredder 3/14/05 10:09 AM Page 6

MAINTENANCE
For best performance it is recommended that you oil the cutting blades whenever a decrease in shred
capacity is noticed. Follow the steps below to oil your cutting blades (see Figure 5).
1. Pour a stream of shredder oil onto a sheet of paper.
2. Turn the shredder on and shred the lubricated sheet.
3. When shredding is complete, switch the shredder into reverse to help distribute the lubricant
across the cutting blades.
4. Repeat as necessary.
WARNING: GBC recommends only the Shredmaster lubricant which is a non-flammable, non-
aerosol and biodegradeable formula. The use of other lubricants, areosols or pump sprays may
be a fire or combustion hazard due to the solvent content, atomization or the propellant.
ACCESSORIES
Shred Bags: Please refer to the label on the inside of the front door of your shredder cabinet for the
part number for the proper bag for your unit.
Shredder Oil: Order Part Number 1760049
To order contact your dealer or call GBC National Service at 1-800-790-7787.
TROUBLESHOOTING
If your machine does not function please check the following:
SYMPTOM CORRECTIVE ACTION
Unit will not run Plug unit in.
Switch unit to Power On position (green LED lights up).
Feed paper into the center of the feed opening (photo cell).
Close cabinet door.
Empty shred bag.
Decrease in sheet capacity (see Fig. 6) Lubricate cutting blades per “Maintenance” section of this Manual.
Machine will not stop (see Fig. 7) Remove plug. Clean the photocell with a small brush.
Machine stops Overload protection, cooling down period approx. 5-10 minutes.
If none of the above actions correct the problem contact your local dealer or call GBC National Service at
1-800-790-7787.
07
FIGURE 6FIGURE 7
!
3890 shredder 3/14/05 10:09 AM Page 7

INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Su seguridad así como la de los demás es importante para GBC. En este manual de
instrucciones y en el producto encontrará mensajes importantes de seguridad. Lea estos
mensajes atentamente.
El símbolo de alerta de seguridad precede a cada mensaje de seguridad que se incluye en
este manual de instrucciones y en el producto. Este símbolo indica un peligro potencial a
la seguridad personal que podría lesionarlo a usted o a otros, además de provocar daños al
producto o a la propiedad. No conecte esta unidad a una fuente de energía eléctrica ni intente
ponerla en funcionamiento antes de leer estas instrucciones de funcionamiento. Guarde estas
instrucciones para futuras consultas.
La siguiente advertencia se encuentra en la parte inferior del producto:
Los siguientes símbolos ISO e IEC aparecen en este producto y significan lo siguiente:
Significa que la trituradora está en modo de recepción y la corriente está conectada.
Significa que está APAGADA
Los símbolos que se iluminan son:
08
Significa que la corriente está ENCENDIDA (ON)/en modo de recepción
Significa que la corriente está APAGADA (OFF)
Significa que el recipiente de depósito de papel está lleno
Significa que la puerta del mueble está abierta
Este mensaje de seguridad significa que usted podría
perder la vida o resultar gravemente herido si abre el
producto y se expone a voltajes peligrosos.
Este mensaje de seguridad significa que usted podría
resultar gravemente herido si coloca sus manos en el
área de descarga.
!
La siguiente advertencia se encuentra en la parte interior de la puerta del mueble:
E
3890 shredder 3/14/05 10:09 AM Page 8

INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Esto significa que debe tener cuidado porque el cabello largo puede enredarse en el
cabezal de corte. Esto podría lastimarlo.
Esto significa que debe mantener las manos alejadas de la abertura de alimentación del
cabezal de corte. Esto podría lastimarlo.
Esto significa que debe tener cuidado con las corbatas y otras prendas de vestir sueltas
que podrían enredarse en el cabezal de corte. Esto podría lastimarlo.
Esto significa que debe tener cuidado porque las alhajas podrían enredarse en el cabezal
de corte. Esto podría lastimarlo.
Esto significa que no debe permitir que la trituradora sea usada por niños.
PRECAUCIONES ELÉCTRICAS
•Desenchufe la trituradora antes de moverla, vaciar la bolsa, o cuando no vaya a usarla
durante un largo período de tiempo.
•No ponga la máquina en funcionamiento si el cable o el enchufe de alimentación de energía
están en mal estado, después de una falla en el funcionamiento o después de que haya sido
dañada de alguna manera.
•No sobrecargue los tomacorrientes eléctricos ya que esto puede resultar en un incendio o
choque eléctrico.
•El tomacorriente debe estar instalado junto a la máquina y debe ser de fácil acceso.
•No altere el enchufe de conexión. El enchufe está configurado para el suministro eléctrico
apropiado.
•No use cerca del agua.
•Mantenga fuera del alcance de los niños.
•No use cables de extensión para conectar este producto al suministro de energía.
SERVICIO
No intente realizar un servicio ni reparar la unidad usted mismo. Si su trituradora necesitara
servicio, póngase en contacto con su distribuidor local.
09
ADVERTENCIA
NO use limpiadores ni rociadores en aerosol.
NO rocíe nada dentro de la trituradora.
Las sustancias extrañas pueden ser explosivas.
E
3890 shredder 3/14/05 10:09 AM Page 9

010
ARMADO
¡Precaución! Las trituradoras son un equipo
pesado (vea “Peso total de la unidad” en la
sección “Especificaciones” de este manual). Para
asegurar una correcta instalación y evitar lesiones,
GBC recomienda que dos personas armen esta
unidad.
FIGURA 1. Comience por abrir la puerta del mueble
tirando de la manija. Coloque el cabezal de la
trituradora encima del mueble tal como aparece en
la ilustración.
FIGURA 2. Introduzca la bolsa de plástico adjunta
en el receptáculo deslizante para residuos. Primero,
deslice hacia afuera el receptáculo para residuos
(1) y quite la correa roja redonda (2). Enrosque la
parte superior de la bolsa varias veces (3),
introduzca la bolsa de plástico en el receptáculo
para residuos y ajuste con la correa redonda (4).
Empuje el receptáculo para residuos hacia adentro
del mueble y cierre la puerta del mueble (5).
FIGURA 1
FIGURA 2
!
1
2
3
4
5
E
3890 shredder 3/14/05 10:09 AM Page 10