GBO Technology S1080 IP User manual

GBO TECHNOLOGY
S1080 IP Network Camera
QuickReference
Guide

United States Offices and Customer Service
GBO Technology (US) Incorporated
Address: 1150 Bayhill Drive
Suite 111
San Bruno, CA 94066 USA
Phone: [phone]
E-mail: [e-mail]
[email protected]m.au
Unpublished copyright @2013 GBO Technology, Inc. All rights reserved. This document is the property of and
contains information proprietary to GBO Technology, Inc. No part of this document may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the written permission of GBO Technology, Inc.

Quick Reference Guide
QRG-S1080-1000
Revision B
August 22, 2013 Company Proprietary Information Page i of ii
Table of Contents
1.0 CONFIGURE THE CAMERA FOR THE LENS TYPE...................................................................................................1
2.0 INSTALL THE CAMERA FOR THE FIRST TIME .......................................................................................................1
2.1 Camera Connected Directly to a Personal Computer......................................................................1
2.2 Standalone POE Switch Installation.................................................................................................5
2.3 UPNP- and DHCP-Enabled Network Installation.............................................................................6
2.4 Use DCHP to Obtain an IP Address Automatically..........................................................................7
3.0 WEB BROWSER GUI SCREEN...........................................................................................................................8
3.1 Select Stream(s) to View..................................................................................................................8
3.2 Icons.................................................................................................................................................8
4.0 ADD/EDIT USERS SCREEN................................................................................................................................9
5.0 VIDEO SETTINGS............................................................................................................................................10
5.1 Advanced Video Settings ...............................................................................................................12
5.2 Face Detection - Region of Interest................................................................................................12
6.0 ADVANCED FEATURES SCREEN ......................................................................................................................13
7.0 CAMERA........................................................................................................................................................14
7.1 Camera –Advanced Settings.........................................................................................................15
7.2 Camera –Pan/Tilt...........................................................................................................................15
7.3 Alignment Controls .........................................................................................................................16
8.0 AUDIO ...........................................................................................................................................................16
9.0 DATE/TIME ....................................................................................................................................................17
10.0 NETWORK AND PORT SCREEN........................................................................................................................18
11.0 ALARM ..........................................................................................................................................................19
12.0 STORAGE ......................................................................................................................................................21
12.1 Create a Recording Schedule ........................................................................................................21
12.2 Upload Files at the Storage Screen ...............................................................................................22
12.3 Upload Files At the Alarm Screen ..................................................................................................22
List of Figures
Figure 1 Back of Camera Showing DIP #1 in Position 2 ........................................................................................1
Figure 2 Camera Connected Directly to PC...........................................................................................................2
Figure 3 OnVIF Main Screen and Log In................................................................................................................2
Figure 4 Wrench Icon and Application Settings Screen........................................................................................3
Figure 5 Internet Explorer Screen.........................................................................................................................3
Figure 6 Internet Options......................................................................................................................................4
Figure 7 GBOT IP Network Camera Log In Screen ................................................................................................4
Figure 8 Web Browser GUI Screen (Live Video Screen)........................................................................................4
Figure 9 Set Browser Window Size .......................................................................................................................5
Figure 10 PC to Standalone POE Switch to Camera................................................................................................5
Figure 11 Back of Camera and POE Switch .............................................................................................................5
Figure 12 PC to POE Switch to Cameras .................................................................................................................6
Figure 13 UPnP Icon for GBOT IP Network Camera................................................................................................6
Figure 14 Ethernet Icon ..........................................................................................................................................7
Figure 15 Live Video Screen....................................................................................................................................8
Figure 16 Live Video Screen Icons...........................................................................................................................8
Figure 17 Add/Edit Users Screen ............................................................................................................................9
Figure 18 Video Screen .........................................................................................................................................10
Figure 19 Advanced Video and Region of Interest Screens..................................................................................12
Figure 20 Advanced Features Screen....................................................................................................................13

QRG-S1080-1000
Revision B
Quick Reference Guide
Page ii of ii Company Proprietary Information August 22, 2013
Figure 21 Camera Settings Screen ........................................................................................................................14
Figure 22 Camera > Pan/Tilt Screen......................................................................................................................15
Figure 23 Audio Setting Screen.............................................................................................................................16
Figure 24 Date/Time Screen .................................................................................................................................17
Figure 25 Network and Port Screen......................................................................................................................18
Figure 26 Alarm Screen.........................................................................................................................................19
Figure 27 Storage Screen ......................................................................................................................................21
List of Tables
Table 1 Video Screen Selections........................................................................................................................10
Table 2 Camera Settings ....................................................................................................................................14
Table 3 Pan/Tilt Settings....................................................................................................................................15
Table 4 Audio Settings.......................................................................................................................................16
Table 5 Date and Time Settings.........................................................................................................................17
Table 6 Alarm Settings.......................................................................................................................................19
Touch Screen Users:
The instructions in this manual are written for regular personal computers. For touch
screen computers, simply substitute the word "touch" for "click on" or "select".

Quick Reference Guide
QRG-S1080-1000
Revision B
August 22, 2013 Company Proprietary Page 1 of 22
1.0 CONFIGURE THE CAMERA FOR THE LENS TYPE
The two most commonly used types of lenses on the GBOT S1080 IP Network Camera are the manual iris lens and the
DC Iris (direct control iris) lens. The factory-set default is for the manual iris lens.
If a manual iris lens is being used, the camera is pre-configured and requires no action.
If a DC Iris lens is being used, a DIP switch setting on the back of the camera needs to be changed.
At the back of the camera there are two DIP switches, #1 and #2. Flip DIP switch #1 into position 2 when using a DC Iris
lens (as shown in Figure 1).
Figure 1 Back of Camera Showing DIP #1 in Position 2
2.0 INSTALL THE CAMERA FOR THE FIRST TIME
There are three ways to install the GBOT S1080 IP Network Camera:
(1) By connecting the camera directly to your personal computer (PC). See Section 2.1, Camera Connected Directly
to a Personal Computer.
(2) By connecting the camera to a standalone Power-over Ethernet (POE) switch that is connected to your PC.
See Section 2.2, Standalone POE Switch Installation.
(3) By connecting it to a network via a POE switch. See Section 2.3, UPNP- and DHCP-Enabled Network Installation.
2.1 Camera Connected Directly to a Personal Computer
These instructions describe how to use the OnVIF Device Manager application to interface with the camera’s software
with the camera connected directly to a standalone PC.
Step 1. Download “OnVIF Device Manager”
From the internet, download the OnVIF Device Manager application from
http://sourceforge.net/projects/onvifdm/. After the application has down-loaded, the OnVIF icon displays on
your desktop.
Step 2. Power On Standalone PC
Before connecting the camera, power-on the standalone PC, without the Ethernet cable connection, and second,
ensure that the PC’s Ethernet interface is configured to use DHCP to obtain an IP address automatically. See Section,
2.4, Use DCHP to Obtain an IP Address Automatically, for detailed information on required PC settings.
DIP Switch #1
in position 2
LAN LED
Power
LED

QRG-S1080-1000
Revision B
Quick Reference Guide
Page 2 of 22 Company Proprietary Information August 22, 2013
Step 3. Connect Camera to Your Computer
Using an Ethernet cable, connect one end of the cable to the LAN/POE slot in the back of the camera and the other end
to your computer (see Figure 2).
Figure 2 Camera Connected Directly to PC
Step 4. Power On Camera with DC Power Supply
Insert the connector end of the camera’s power supply cable into the DC 12V receptacle located on the back 1.
of the camera. Plug the electrical end of the power supply cable into a power outlet.
Wait until the two camera LEDs light up. Initially they are red/orange in color; when they both turn green,2.
the camera is “on”and working correctly (see Figure 1)
Step 5. Open “OnVIF Device Manager”
Open the OnVIF application by double-clicking on its icon on your desktop and its Main Screen opens.1.
At the OnVIF Main Screen, check the Remember checkbox (see Figure 3).2.
Enter your Name (admin) and Password (9999).3.
Figure 3 OnVIF Main Screen and Log In
Click on the Log in button.4.
Your camera’s IP address is shown in the gray box as Address.5.
Step 6. Change Settings
Click on the wrench icon located at the top right side of the OnVIF Main Screen (see Figure 4). The1.
Application settings dialog box opens.
Name
Password
Log in
button
Your camera’s
IP Address
Ethernet Cable
LAN/POE/slot
Remember
checkbox
Standalone PC
Camera

Quick Reference Guide
QRG-S1080-1000
Revision B
August 22, 2013 Company Proprietary Page 3 of 22
Figure 4 Wrench Icon and Application Settings Screen
Change the Video rendering fps to 15.Click on Open web in external browser checkbox.2.
Change Video streaming transport to UDP from the drop-down list. Click on the Apply button and wait for3.
the changes to take effect.
Step 7. Open Web Page
At the OnVIF Main Screen (see Figure 3), click on Web page and a black screen opens with a message that1.
asks you to allow add-ons before the GBOT IP Network Camera Log In Screen can be opened.
Click on the Allow button, and the GBOT IP Network Camera Log In Screen opens with the same question at2.
the bottom of the screen.
Click on the Allow button again, and you can log in (see Step 10, Log In). Skip Step 7 and Step 8.3.
NOTE:
If the GBOT IP Network Camera Log In Screen does not open after approximately one minute, the default
Home Page setting on your browser may be causing a long timeout. Follow the instructions in Step 7, Set
Browser Default to Blank, below, to correct this.
Step 8. Set Browser Default to Blank
At your Internet Explorer screen, click on the Settings icon located in the upper right-hand corner of1.
the screen.
Figure 5 Internet Explorer Screen
Video rendering fps
Open web in
external
browser
Wrench icon
Apply button
UDP

QRG-S1080-1000
Revision B
Quick Reference Guide
Page 4 of 22 Company Proprietary Information August 22, 2013
Click on Internet options and the Internet Options dialog box opens.2.
Delete the text in the Home Page text box, and click on the OK button.3.
Step 9. Open Web Page –After Changing Browser Setting
Back at the OnVIF Main Screen, click on Web Page again (see Figure 3).1.
Follow the steps in Step 7, Open Web Page and proceed to Step 9.2.
Step 10. Log In
Enter the User Name (admin) and Password (9999), and then click on1.
the Submit button (see Figure 7).
After successful login, a live video from the camera starts streaming in2.
the Live Video section of the Web Browser GUI Screen (see Figure 8).
Figure 7 GBOT IP Network Camera Log In Screen
Figure 8 Web Browser GUI Screen (Live Video Screen)
CAUTION:
If your Browser screen size is not set to 100%, the bottom of some buttons may be cut off. Follow the
instructions in Step 11, Set Browser Size, to set your Browser to the correct size.
Figure 6 Internet Options
(1) Live Video
Section
(2) Navigation
Panel

Quick Reference Guide
QRG-S1080-1000
Revision B
August 22, 2013 Company Proprietary Page 5 of 22
Step 11. Set Browser Size
At the Internet Explorer screen, click on the Settings icon located in the upper right-hand corner of the1.
screen.
Select Zoom (100%) from the drop-down menu, and then select 100% from the second drop-down menu2.
(see Figure 9). Your Browser window will now be the correct size.
Figure 9 Set Browser Window Size
2.2 Standalone POE Switch Installation
This installation requires the camera and your PC to be connected to a standalone POE switch via two Ethernet cables.
It uses the OnVIF Device Manager application to interface with the camera’s software.
Figure 10 PC to Standalone POE Switch to Camera
Step 1. Connect PC to POE Switch
Using an Ethernet cable, connect one end to the POE switch and the other to your PC (see Figure 10).
Step 2. Power-On PC
First, power-on the PC to ensure that the PC’s Ethernet interface is configured to use DHCP to automatically obtain an
IP address. In this case, because there is no DHCP server running on the network, the PC will obtain an Auto-IP address
in the 169.254.0.0 class B subnet. See Section 2.4, Use DCHP to Obtain an IP Address Automatically, for detailed
information on required PC settings.
Step 3. Connect Camera to Standalone POE Switch
Using an Ethernet cable, connect one end of the cable to the LAN/POE slot in the back of the camera and the1.
other end to the POE switch (see Figure 11). The POE switch provides DC power to the camera so that the
camera’s DC power cable is not needed.
Figure 11 Back of Camera and POE Switch
Ethernet Cable
Ethernet Cable
Standalone POE Switch
LAN/POE/slot
Ethernet
Cable
POE Switch
Standalone PC
Camera

QRG-S1080-1000
Revision B
Quick Reference Guide
Page 6 of 22 Company Proprietary Information August 22, 2013
Wait until the two camera LEDs light up. Initially they are red/orange in color; when they both turn green,2.
the camera is “on”and working correctly (see Figure 1).
Step 4. Use “OnVIF Device Manager”
Follow Steps 4-10 of Section 2.1, Camera Connected Directly to a Personal Computer.
2.3 UPNP- and DHCP-Enabled Network Installation
The GBOT IP Network Camera is designed to be used on an IP network and needs an IP address. Most networks have a
DHCP server that automatically assigns an IP address to a connected device.
Step 1. Connect Camera(s) to PC Using Ethernet Cable(s) and POE Switch
Using a standard Ethernet cable, connect the power-over-Ethernet (POE) switch to your PC.1.
Using standard Ethernet cable(s) connect the POE switch to the camera(s) through the LAN/POE
2.
receptacle(s) located on the back of the camera(s).
Figure 12 PC to POE Switch to Cameras
Step 2. Power On Camera Through POE
The camera is powered-up through the POE 802.3af-enabled network switch. (If POE support is not available, an
external 12V DC power supply is required. See Step 3, Power On Camera with DC Power Supply, in Section 2.1,
Camera Connected Directly to a Personal Computer.)
Step 3. Starting the Web Browser GUI Using UPnP
By default, the GBOT S1080 IP Network Camera has the User Plug and Play (UPnP) functionality enabled (see that the
Enable UPNP checkbox is checked in the Network and Port Screen (see Figure 25).
To start the Web Browser GUI, browse to the PC’s Network dialog box. Under Other Devices, double-click1.
the GBO_DD:EE:FF icon, where DD:EE:FF represents the last three bytes of the camera’s media access
control (MAC) address.
Figure 13 UPnP Icon for GBOT IP Network Camera
Ethernet Cable
Ethernet Cables
Camera’s MAC address
UPnP GBO S1080 icon
Networked PC
Cameras
POE Switch

Quick Reference Guide
QRG-S1080-1000
Revision B
August 22, 2013 Company Proprietary Page 7 of 22
Internet Explorer needs the user’s permission to run the camera Web Browser GUI. As the three dialog2.
boxes display, select first Install, then select Install again, and then Allow, to proceed.
Step 4. Log In via Web Browser GUI
The GBOT IP Network Camera Log In screen displays when the connection to the GBOT S1080 IP Network1.
Camera has been successful. Enter the User Name (admin) and Password (9999), and then click on the
Submit button (see Figure 7).
After successful installation and login, a live video from the camera starts streaming in the Live Video2.
section of the Web Browser GUI Screen, which has two sections: (1) the Live Video Section, and (2) the
Navigation Panel (see Figure 8).
2.4 Use DCHP to Obtain an IP Address Automatically
To verify that your computer’s Ethernet interface is configured to automatically obtain an IP address, follow the steps
below.
On your desktop, right-click on the Ethernet icon and the Network and Sharing Center dialog box opens1.
(see Figure 14). Go to step 3.
Figure 14 Ethernet Icon
Or, open your Control Panel and click first on Network and Internet, and when the Network and Internet2.
dialog box opens, click on Network Sharing Center.
When the Network and Sharing Center dialog box opens, click on Change adapter settings, and the3.
Network Connections dialog box opens.
Scroll down and double-click on Internet Protocol Version 4 (TCP/IPv4), and the Internet Protocol Version 44.
(TCP/IPv4) Properties dialog box opens.
Ensure that both Obtain an IP address automatically and Obtain DNS server address automatically radio5.
buttons are checked.
Click on the OK button to close the dialog box.6.

QRG-S1080-1000
Revision B
Quick Reference Guide
Page 8 of 22 Company Proprietary Information August 22, 2013
3.0 WEB BROWSER GUI SCREEN
3.1 Select Stream(s) to View
The Live Video screen is the default Web Browser GUI Screen and displays when the software is opened. Three
stream selections are available for you to view, either singly, from the drop-down list, or at the same time. The Stream
Type must first be selected at the Settings Video Screen (see Figure 18) and the Display all streams check box must
be enabled.
Figure 15 Live Video Screen
3.2 Icons
Click on any of the icons to perform routine tasks. Before they are operational, the icons have to be enabled and some
conditions have to be preset.
Figure 16 Live Video Screen Icons
1X Display Icon: Click on the 1X Display icon to expand the streaming video to the whole screen.1.
A scroll bar on the screen allows the user to move up and down the screen. Click on the Close 1X Mode
button to close.
Snapshot Icon: Click on the Snapshot icon to capture and store the first resolution JPEG image2.
of whatever the camera is “seeing” right now.
Alarm Status Icon: The Alarm Status icon has to be enabled from the Settings →Alarm3.
screen, and an alarm trigger must be selected, i.e., Motion Detected, Ethernet Lost, or Audio Alarm (see
Section 11.0, Alarm).

Quick Reference Guide
QRG-S1080-1000
Revision B
August 22, 2013 Company Proprietary Page 9 of 22
When any of the preset conditions are met, the alarm is triggered and the alarm icon changes from inactive to
activate. The alarm icon changes color from white to orange to give the user a visual signal that the alarm state
has changed.
Record Status Icon: The Record Status icon indicates whether the camera is actively4.
recording, or if it is in an inactive state. Recording may be initiated for a specified period of time or for
whenever an alarm is triggered. The conditions are set at the Settings →Alarm or Settings →Storage
screens (see Sections 11.0, Alarm and 12.0, Storage).
Audio Toggle Icon: Click on the Audio icon to toggle the sound at the camera location from5.
OFF to ON. A pre-selected Warning signal may be initiated. The conditions are set at the Audio Setting
screen (see Section 8.0, Audio).
SD Card Explorer Icon: This icon is only available if an SD card has been previously inserted into6.
the SD receptacle in the camera. Otherwise, it is missing.
Logout Button: Click on the Logout button to close the Web Browser GUI screen.7.
4.0 ADD/EDIT USERS SCREEN
AT the Live Video Screen (see Figure 15), click on Add/Edit Users and the Add/Edit Users Screen opens. You can add
users and/or edit user names and password. You may also wish to change your password as soon as possible since the
default password is the same for all cameras and is factory set.
Click on the OK button to save your selections and wait for the changes to take effect.
Figure 17 Add/Edit Users Screen

QRG-S1080-1000
Revision B
Quick Reference Guide
Page 10 of 22 Company Proprietary Information August 22, 2013
5.0 VIDEO SETTINGS
At the Live Video Screen (see Figure 15), click on Settings Video and the Video Screen opens. Here you make
selections to determine how the live streaming video will appear. These selections are described in Table 1, below.
Figure 18 Video Screen
Table 1 Video Screen Selections
Selection
Action
1. Camera
Shows you the camera that is currently being used.
2. Stream Type
Select: Single, Dual, Tri-Stream
3. Codec Combo
1) Single: H.264, MPEG4, or Megapixel JPEG
2) Dual: H.264 + JPEG, MPEG4 + JPEG, Dual H.264, Dual MPEG4, or H.264 + MPEG4
3) Tri-Stream: Dual H.264 + JPEG, Dual MPEG4 + JPEG
4. Resolution*
H.264, MPEG, JPEG
(Various settings, depending on Stream Type and Codec Combo settings.)
5. Stream Screens
1) Frame Rate+.Options include 1, 8, 15, 24, or 30 frames per second (fps).
2) Bit Rate‡. Values range from 64 to 12000 Kpbs for Stream 1, and 64 to 8000Kpbs for
Stream 3. Stream 2 does not have a bit rate field
3) Rate Control: Off, VBR, or CBR (see GBOT S1080 User Manual for definitions)
4) Quality Factor (only Stream 2 has this field): Enter a value up to thirty.

Quick Reference Guide
QRG-S1080-1000
Revision B
August 22, 2013 Company Proprietary Page 11 of 22
Selection
Action
6. Overlay Settings
1) Date. Click on Enable Date check box to activate the date function.
2) Time.Click on Enable Time checkbox to activate the time function.
3) Logo. Click on Enable Logo check box to activate the logo function. Select a position for
the logo: top-left or top-right.
4) Text. Click on Enable Text check box to activate the text function. This enables insertion
of a pre-selected text onto the live video image. Enter the text into the field, and select a
position: top-right or top-left.
5) Detailed info. Select to insert camera information onto the live video screen.
7. H.264 profile
Select: High, Base, or Main. Base is the least CPU intensive setting, and High is the most CPU
intensive setting.
8. Local Display
Select: NTSC, PAL, or off.
9. Mirror
Select: vertical, horizontal, both, or off.
10. Video File Stream
Select which stream is to be saved: H.264(1280x720) or H.264(32x192).
11. Video Size
Select the length of the AVI file to be saved for either a scheduled recording or an Alarm
Trigger: 5 or 10 seconds.
*Resolution is image quality and is measured in megapixels. Pixels are the tiny light capturing elements on the camera’s
sensor. The higher the number of pixels (or megapixels), the higher is the resolution of the camera.
+The frame rate is the number of frames or images that are transmitted over the network.
‡The bit rate is the rate at which bits are transferred from one location to another. In other words, it measures how much
data is transmitted in a given amount of time. A higher bit rate gives a better quality image. Bit rate is commonly
measured in bits per second (bps), kilobits per second (Kbps), or megabits per second (Mbps).
Click on the OK button to save your selections and wait for the changes to take effect.

QRG-S1080-1000
Revision B
Quick Reference Guide
Page 12 of 22 Company Proprietary Information August 22, 2013
5.1 Advanced Video Settings
Click on the Advanced button on the Video Screen and the Advanced Video Screen opens. Here you can make
additional selections to control the live streaming video. These are advanced settings and are described in the GBOT
S1080 User’s Manual. Setting a Region of Interest, where faces can be detected or masked, is described below.
Figure 19 Advanced Video and Region of Interest Screens
5.2 Face Detection - Region of Interest
Click on the Enable Region of Interest (ROI) check box and a Configure Table (see Figure 19) opens on top of
1.
the screen.
Click on the Configure button and the Region of Interest screen opens. Drag the mouse to draw the Region.2.
Clicking on the Clear button removes the region.
Optionally, the user can enter the value directly into the X, Y, W and H text boxes. X and Y are the starting3.
coordinates of the region, and W and H are the width and height of the region. The entire region is selected
by default.
Click on the OK button to save your selections and wait for the changes to take effect.4.
Regions of interest

Quick Reference Guide
QRG-S1080-1000
Revision B
August 22, 2013 Company Proprietary Page 13 of 22
6.0 ADVANCED FEATURES SCREEN
Live Video Screen (see Figure 15), click on Settings Advanced Features, and the Advanced Features screen opens.
At this screen you can configure how you want motion and faces to be detected. You can also set privacy areas where
a black box blanks out specified areas on the live video.
Figure 20 Advanced Features Screen
Configure these features the same way you set the ROI (see Section 5.2, Face Detection - Region of Interest):
Click on the Configure button.1.
Click on Enable Motion Window OSD indication (on-screen display) check box. You will receive visual2.
feedback when motion is detected (flashing red boxes on the screen). The Motion Detection Alarm Trigger
must first be enabled at the Settings Alarm screen (see Section 11.0, Alarm, for more detailed
information).
Set the parameters when the screen opens and select areas by clicking on them with the mouse.3.
Click on the OK button to save your selections and wait for the changes to take effect.4.

QRG-S1080-1000
Revision B
Quick Reference Guide
Page 14 of 22 Company Proprietary Information August 22, 2013
7.0 CAMERA
At the Live Video Screen (see Figure 15), click on Settings Camera, and the Camera screen opens. At this screen you
can set camera settings. These selections are described in Table 2, below. Refer to the Definitions section of the GBOT
S1080 User’s Manual for more information on the parameters set at this screen.
Figure 21 Camera Settings Screen
Table 2 Camera Settings
Selection
Action
1. Lighting Condition:
a. Brightness
Use the slider to specify the desired brightness level from 1 to 255. A higher value
of the brightness gives a brighter scene.
b. Contrast
Use the slider to specify the desired contrast level from 1 to 255.
c. Saturation
Use the slider to specify the desired saturation level from 1 to 255. A higher value
of the saturation results in a more vivid scene.
d. Sharpness
Use the slider to specify the desired sharpness level from 1 to 255.
2. Backlight
Specify: Min: Whole image average,
Mid: Center weighted
Max: Spot
3. Flicker Control
Specify the desired frequency of flicker control. In PAL countries, use a
multiple of 50; in NTSC countries, use a multiple of 60.
4. White Balance
Specify the white balance mode.
5. Day/Night
Specify one of the following mode options: Auto, Day/Color), or Night/ Mono.
Threshold
Use the slider to specify threshold value from 1 to 16.
Histogram

Quick Reference Guide
QRG-S1080-1000
Revision B
August 22, 2013 Company Proprietary Page 15 of 22
Selection
Action
6. Histogram
Enable/disable histogram on the primary video stream: ON or OFF (see an
example in Figure 21).
7. Lens Distortion Correction
Enable/disable lens distortion: ON or OFF.
Click on the OK button to save your selections and wait for the changes to take effect.
7.1 Camera –Advanced Settings
Click on the Advanced button on the Camera Screen and the Advanced Video Screen opens. Here you can make
additional selections to the camera. These advanced settings are described in the GBOT S1080 User’s Manual.
7.2 Camera –Pan/Tilt
At the Settings Camera Screen (see Figure 21), click on the Pan/Tilt Button, located at the bottom-right side of the
screen, and the Camera > Pan/Tilt Screen opens. At this screen you can set pan and tilt conditions. These selections
are described in Table 3, below.
Figure 22 Camera > Pan/Tilt Screen
Table 3 Pan/Tilt Settings
Selection
Action
1. Pan Speed
Use the slider to specify the desired pan speed from 0 to 64; the default is 32. A higher
value gives a faster pan speed.
2. Tilt Speed
Use the slider to specify the desired tilt speed from 0 to 63; the default is 32. A higher
value gives a faster tilt speed.
3. Baud Rate
Specify the baud rate from the drop-down list.
4. Zoom Speed
Specify the zoom speed from 0 to 3.
Alignment
Controls

QRG-S1080-1000
Revision B
Quick Reference Guide
Page 16 of 22 Company Proprietary Information August 22, 2013
Selection
Action
5. Focus Speed
Specify the focus speed from 0 to 3.
Click on the Store button to save your selections and wait for the changes to take effect.
7.3 Alignment Controls
Click first on the Center button, and then click on the Store button to center the camera on the desired location. Or,
use the directional arrows to move the camera in the direction indicated, and then click on the Store button to save
the camera position.
Click on the Clear button to clear all position settings. Click on the Store button to save position changes. Click on the
Back button to return to the Camera Settings Screen.
8.0 AUDIO
At the Live Video Screen (see Figure 15), click on Settings Audio, and the Audio screen opens. At this screen you
can set advanced audio conditions. Only the primary settings are described in Table 4, below. Refer to the GBOT
S1080 User’s Manual for more information on the parameters set at this screen.
Figure 23 Audio Setting Screen
Table 4 Audio Settings
Selection
Action
1. Enable Audio
Click this checkbox to enable the functionality. The Audio Mode drop-down list opens.
Specify one of the following audio modes: MIC Only, Speaker Only, or MIC and Speaker.
2. Alarm Level
Use the slider to specify the Audio Level that must be captured by the camera in order
to trigger an audio alarm. The Enable Alarm check box must be checked before the
alarm level can be set (see Section 11.0, Alarm).