GE GFDN110ED Manual

Specification Revised 10/15
GFDN110ED
GE®Series 7.0 Cu. Ft. Super Capacity Front Load Electric Dryer
For answers to your Monogram, GE Profile™ Series
or GE®Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Listed by
Underwriters
Laboratories
Dimensions anD installation information (in inches)
exhaust options: 4-way via rear, right, left and bottom.
circuit requirements: An individual, properly grounded
branch circuit, protected by a 30-amp circuit breaker or a time-
delay fuse, is required.
note: Dryer wall outlet must be located within 36" of service
cord entry and accessible when dryer is mounted in position.
installation information: For complete information,
see installation instructions packed with your dryer.
2-1/2
1-3/4
12
3-1/2
Electrical
Connection
Gas Pipe
Connection
27 32-3/16
39-3/8
4-1/2
4-3/8
electric Dryer rating
120V/240V 5600W, 24A, 60Hz
120V/208V 4400W, 22A, 60Hz

Specification Revised 10/15
GFDN110ED
GE®Series 7.0 Cu. Ft. Super Capacity Front Load Electric Dryer
For answers to your Monogram, GE Profile™ Series
or GE®Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
special installation requirements:
stacke D installation:
Brackets for stacking dryer over washer are not included with the dryer.
GEFLSTACK or part no. WE25X10018.
alcove or closet installation:
If your dryer is approved for installation in an alcove or closet, it will be
stated on a label on the dryer back.
The dryer MUST be exhausted to the outside.
Minimum clearances between dryer cabinet and adjacent walls or other
surfaces are: 0" either side, 3" front and rear.
Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
No other fuel-burning appliance shall be installed in the same closet with
a gas dryer.
Bathroom or BeDroom installation:
The dryer MUST be exhausted to the outdoors.
The installation must conform with the local codes, or in the absence of
local codes, with the National Electric Code and National Fuel Gas Code,
ANSI Z223 for gas dryers.
minimum clearance other than alcove or closet
installations:
Minimum clearances to combustible surfaces 0" both sides, 3" rear.
for more information on venting kits anD accessories,
please call 1-800-ge-cares.
27
13
28-3/4
Listed by
Underwriters
Laboratories
1/2
49-5/8
24 3-1/4
79-5/8
stackeD Dimensions
(in inches)
peDestal Dimensions (in inches)
sBsD137hWW - White
This optional 13" pedestal raises the door
opening and height of the washer or dryer.
Feet on 13" pedestal allow it to adjust to
13-3/8" height.

Special inStallation RequiRementS
Specification Revised 10/15
GFDn110eD
GE®Series 7.0 Cu. Ft. Super Capacity Front Load Electric Dryer
For answers to your Monogram, GE Profile™ Series
or GE®Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Dryer exhausting information – Metal duct only.
For complete information, see installation instructions packed with your dryer.
Ducting materials: For best performance, this dryer should be vented with 4" diameter
all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal
(semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary
to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible
metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal
(semi-rigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the
entire length of the transition duct. Please see installation instruction packed with your dryer for
complete instructions when using flexible metal (foil type) ducting.
exhaust length calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house
floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture
could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen
exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc.
The wall cap must also be located at least 12" above the ground or any other obstruction with the
opening pointed down.
for more information on venting kits anD accessories, please call
1-800-ge-cares.
BEST PERFORMANCE
Maximum length
of 4" dia rigid
metal duct
Exhaust hood type
Domestic dryer models
Number
of 90°
turns
A
4"
opening
B
2-1/2"
opening
GE Front Load Long Vent 7.0
cu. ft. capacity electric dryer
(GFDL)
0200 ft. 175 ft.
1185 ft. 165 ft.
2175 ft. 155 ft.
3165 ft. 145 ft.
4155 ft. 135 ft.
5145 ft. 125 ft.
Long Vent 6.0 - 8.0 cu. ft.
capacity electric & gas dryers
(GTDL and GTV)
0150 ft. 125 ft.
1135 ft. 115 ft.
2125 ft. 105 ft.
3115 ft. 95 ft.
4105 ft. 85 ft.
595 ft. 75 ft.
Long Vent 7.0 cu. ft. capacity
electric & gas (GTD42, GTD45,
GTD65, GTX42 and GTX60)
0120 ft. 90 ft.
1100 ft. 75 ft.
285 ft. 65 ft.
370 ft. 55 ft.
460 ft. 45 ft.
555 ft. 35 ft.
All 6.0 - 8.3 cu. ft. capacity
models electric and gas dryers
(GFDS, GFDR, GFDN, GTDS,
GTDN, GHDN, GHDS, GTDP,
GLDP, GTD, HTDP, HTDX)
090 ft. 60 ft.
160 ft. 45 ft.
245 ft. 35 ft.
335 ft. 25 ft.
425 ft. 15 ft.
DCVH480
090 ft. 60 ft.
160 ft. 45 ft.
245 ft. 35 ft.
335 ft. 25 ft.
All 3.6 cu. ft. (DSKS, DSKP)
electric dryers
046 ft. 37 ft.
137 ft. 30 ft.
230 ft. 22 ft.
323 ft. 15 ft.
Laundry Center GUD27
056 ft. 42 ft.
148 ft. 34 ft.
240 ft. 26 ft.
332 ft. 18 ft.
Laundry Center GUD24
043 ft. 36 ft.
133 ft. 26 ft.
224 ft. 16 ft.
A
B
2-1/2
4
GE Dryer Vent
A
B
2-1/2
4
GE Dryer Vent
A
Dryer exhausting information—use metal
Duct only vertical anD horizontal Ducting
Listed by
Underwriters
Laboratories

Specification Revised 10/15
GFDN110ED
GE®Series 7.0 Cu. Ft. Super Capacity Front Load Electric Dryer
features anD Benefits
DuraDrum provides long-lasting dependability
HE Sensor Dry – Keep your clothes looking and feeling their best. Dual
thermistors continually monitor temperature with a sensor bar that measures
moisture to prevent over-drying
Speed Dry quickly dries items and small loads for families on the go
eDry option – energy saving option reduces dry temperatures on select
cycles without sacrificing performance
4 heat settings provide the right temperature for the right drying needs
6 dry cycles – additional cycles for your clothes-drying needs
Model GFDN110EDWW – White
GFDN110ED_GDWW