GE GFDR270EH Manual

GFDR270EH/275EH
GE Appliances 8.1 Cu. Ft. Capacity RightHeight™Design Front Load Electric Dryer With Steam
Specification Revised 1/16
For answers to your Monogram, GE Café™Series, GE Profile™Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center®Service, 800.626.2000.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
EXHAUST OPTIONS: 3-way via rear, right and left.
CIRCUIT REQUIREMENTS: An individual, properly
grounded branch circuit, protected by a 30-amp circuit
breaker or a time-delay fuse, is required.
NOTE: Dryer wall outlet must be located within 36"
of service cord entry and accessible when dryer is
mounted in position.
INSTALLATION INFORMATION: For complete
information, see installation instructions packed
with your dryer.
28
47
27-7/8
25-7/8
24-3/8
3/4
7-3/4
34-3/8
34-1/2
34-1/8
28-1/2
23-1/8 2-1/4
24-3/8
ELECTRIC DRYER RATING
120V/240V 5600W, 25A, 60Hz
120V/208V 4300W, 23A, 60Hz
Listed by
Underwriters
Laboratories

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
Listed by
Underwriters
Laboratories
GFDR270EH/275EH
GE Appliances 8.1 Cu. Ft. Capacity RightHeight™Design Front Load Electric Dryer With Steam
Specification Revised 1/16
For answers to your Monogram, GE Café™Series, GE Profile™Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center®Service, 800.626.2000.
SPECIAL INSTALLATION REQUIREMENTS:
ALCOVE OR CLOSET INSTALLATION:
- If your dryer is approved for installation in an alcove or closet, it will be
stated on a label on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other
surfaces are: 0" either side, 3" front and rear.
- Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
- Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with
a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of
local codes, with the National Electric Code and National Fuel Gas Code,
ANSI Z223 for gas dryers.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET
INSTALLATIONS:
- Minimum clearances to combustible surfaces 0" both sides, 3" rear.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES,
PLEASE CALL 1-800-GE-CARES.
Listed by
Underwriters
Laboratories
11-5/8
1-5/8
12-3/8 10-5/8
4-5/8"
25-3/8"
52"
2-1/4"

GFDR270EH/275EH
GE Appliances 8.1 Cu. Ft. Capacity RightHeight™Design
Front Load Electric Dryer With Steam
Specification Revised 1/16
For answers to your Monogram, GE Café™Series, GE Profile™Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center®Service, 800.626.2000.
DRYER EXHAUSTING INFORMATION – Metal duct only.
For complete information, see installation instructions packed with your dryer.
DUCTING MATERIALS: For best performance, this dryer should be vented with 4" diameter all rigid
metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting
can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the
house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used
ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND
where a 4" diameter can be maintained throughout the entire length of the transition duct. Please see
installation instruction packed with your dryer for complete instructions when using flexible metal
(foil type) ducting.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl
space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage.
Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of
lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall
cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES,
PLEASE CALL 1-800-GE-CARES.
BEST PERFORMANCE
Maximum length
of 4" dia rigid
metal duct
Exhaust hood type
Domestic dryer models
Number
of 90°
turns
A
4"
opening
B
2-1/2"
opening
GE Front Load Long Vent 7.0
cu. ft. capacity electric dryer
(GFDL)
0200 ft. 175 ft.
1185 ft. 165 ft.
2175 ft. 155 ft.
3165 ft. 145 ft.
4155 ft. 135 ft.
5145 ft. 125 ft.
Long Vent 6.0 - 8.0 cu. ft.
capacity electric & gas dryers
(GTDL and GTV)
0150 ft. 125 ft.
1135 ft. 115 ft.
2125 ft. 105 ft.
3115 ft. 95 ft.
4105 ft. 85 ft.
595 ft. 75 ft.
Long Vent 7.0 cu. ft. capacity
electric & gas (GTD42, GTD45,
GTD65, GTX42 and GTX60)
0120 ft. 90 ft.
1100 ft. 75 ft.
285 ft. 65 ft.
370 ft. 55 ft.
460 ft. 45 ft.
555 ft. 35 ft.
All 6.0 - 8.3 cu. ft. capacity
models electric and gas dryers
(GFDS, GFDR, GFDN, GTDS,
GTDN, GHDN, GHDS, GTDP,
GLDP, GTD, HTDP, HTDX)
090 ft. 60 ft.
160 ft. 45 ft.
245 ft. 35 ft.
335 ft. 25 ft.
425 ft. 15 ft.
DCVH480
090 ft. 60 ft.
160 ft. 45 ft.
245 ft. 35 ft.
335 ft. 25 ft.
All 3.6 cu. ft. (DSKS, DSKP)
electric dryers
046 ft. 37 ft.
137 ft. 30 ft.
230 ft. 22 ft.
323 ft. 15 ft.
Laundry Center GUD27
056 ft. 42 ft.
148 ft. 34 ft.
240 ft. 26 ft.
332 ft. 18 ft.
Laundry Center GUD24
043 ft. 36 ft.
133 ft. 26 ft.
224 ft. 16 ft.
A
B
2-1/2
4
GE Dryer Vent
A
B
2-1/2
4
GE Dryer Vent
A
DRYER EXHAUSTING INFORMATION—USE METAL
DUCT ONLY VERTICAL AND HORIZONTAL DUCTING
Listed by
Underwriters
Laboratories

GFDR270EH/275EH
GE Appliances 8.1 Cu. Ft. Capacity RightHeight™Design Front Load Electric Dryer With Steam
Specification Revised 1/16
FEATURES AND BENEFITS
RightHeight™Built-in Pedestal – Comfortably load and unload clothes, and use
the top as a folding surface, with this factory-installed pedestal
Detangle Assist – Twisted sheets and comforters are a thing of the past with a
setting that pauses and reverses direction to separate items and reduce wrinkling
Steam Refresh – Rejuvenate lightly worn clothes by getting rid of wrinkles and odors
with this convenient setting using the power of steam
Steam Dewrinkle – Stored or wrinkled clothes come out wrinkle-free with the
helpful setting that uses steam to refresh and dry a load of any size
Stainless steel drum – Resists rust and helps protect clothes
HE Sensor Dry – Keep your clothes looking and feeling their best. Dual thermistors
continually monitor temperature with a sensor bar that measures moisture to prevent
over-drying
Model GFDR270EHWW – White
Model GFDR275EHMC – Metallic Carbon