GE GTX22EBMR User manual

GEAppliances.c a
Dryers
Safety Instructions. . . . . . . . 2–3
Operating Instructions ..4-11
ControlPanels ................. 5-7
DryerFeatures................... 8
Loading and Using the Dryer. . . . . 10
VentingtheDryer...............11
Troubleshooting Tips . . . 12, 13
Consumer Support
Consumer Support ..............16
Warranty .......................15
Write the model and serial
number here:
Model # __________________
Serial # ___________________
You can find them on a label
on the front of the dryer
behind the door.
Owner’s Manual
29-6393 01-21 PrintedinMexico
234D2431P014
GTX22EBMR
GTX33EBMR
GTD40EBMR
GTD40GBMR
MTX22EBMR

2
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill you or hurt you and others. All
safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words
are defined as:
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
DANGER
WARNING
CAUTION
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, explosion, electric shock, or injury to persons when using your appliance, follow basic
precautions, including the following:
 Read all instructions before using the appliance.
DO NOT dry articles that have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry-cleaning
solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.
DO NOT place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a
chemical reaction that could cause a load to catch fire.
DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this appliance
is used near children. Before the appliance is removed from service or discarded, remove the door to the drying
compartment.
DO NOT reach into the appliance if the drum is moving.
DO NOT install or store this appliance where it will be exposed to the weather.
DO NOT tamper with controls,
repair or replace any part of this appliance or attempt any servicing unless specifically
recommended in the user maintenance instructions or in published user repair instructions that you understand and have
the skills to carry out.
DO NOT use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric
softener or product.
DO NOT use heat to dry articles containing foam rubber or similarly textured rubber-like materials.
Clean lint screen before or after each load. DO NOT operate the dryer without the lint filter in place.

Do not store combustible materials, gasoline or other flammable liquids near the dryer. Keep area around the exhaust opening
and adjacent surrounding areas free from the accumulation of lint, dust and dirt. Keep dryer area clear and free from items
that would obstruct the flow of combustion and ventilation air.
The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.
Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power or Start/Pause button DOES NOT
disconnect power.
DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a
damaged cord or plug.

DO NOT spray any type of aerosol into, on or near dryer at any time. Do not use any type of spray cleaner when cleaning dryer
interior. Hazardous fumes or electrical shock could occur
.
See “Electrical Connection” located in the Installation Instructions for grounding instructions.
SAVE THESE INSTRUCTIONS
WARNING
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.

3
GEAppliances.ca
ADDITIONAL GAS DRYER WARNINGS
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion
or to prevent damage, personal injury, or death.
- DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• DO NOT try to light any appliance.
• DO NOT touch any electrical switch; DO NOT use any phone in your building.
• Clear the room, building, or area of any occupants.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
WARNING

4
Clean lint filter Select drying cycle Push Start
Step 1 Step 2 Step 3 Step 4
Add clothes
Shut door
To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
WARNING!
WARNING WARNING
Explosion Hazard Fire Hazard
Keep flammable materials and vapors, such as gasoline, away
from dryer.
DO NOT dry anything that has ever had anything flammable on it
(even after washing).
Failure to do so can result in death, explosion, or fire.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on it
(including cooking oils).
Items containing foam, rubber, or plastic must be dried on a
clothesline or by using an air dry cycle.
Failure to follow these instructions can result in death or fire.
Throughout this manual, features and appearance may vary from your model.
Operating instructions
Quick Start Guide

5
BAC
BAC
BAC
GTX22EBMR / GTX33EBMR
MTX22EBMR
GTD40EBMR, GTD40GBMR

6
IMPORTANT: Clean the lint filter each time you use the dryer.
Temperature (Not all features are on all models)
Cottons For regular to heavy cottons.
Regular
Casuals For synthetics, blends, delicates and items labeled permanent press.
Medium
Air Fluff For fluffing items without heat. Use the Time Dry cycle.
No Heat
Drying Cycles (Not all features are on all models)
Cottons For cottons and most linens. For most loads, select Optimum Dry (on some models).
Casuals For wrinkle-free, permanent press and delicate items, and knits.
Time Dry Set the Cycle Selector at the desired drying time.
Quick Fluff For freshening or fluffing up already dry clothing, fabrics, linens and pillows. Use with Air Fluff No Heat.
Provides 10 minutes of no heat tumbling.
Start Start. Opening the door during operation will stop the dryer.
To restart the dryer, close the door and select Start to complete the cycle.
A
B
SaniFresh (Not all features are on all models
This option reduces certain types of bacteria including: Staphylococcus aureus, Pseudomonas aeruginosa
and Klebsiella pneumoniae. The anti-bacterial process occurs when high heat is used during a portion of
the drying cycle.
NOTE: Do not use this cycle on delicate fabrics.
C
NOTE: Drying times will vary according to the type of heat used (Electric, Natural or LP gas), size of load, types of fabrics,
wetness of clothes and condition of exhaust ducts.

7
Before replacing the light bulb, be sure to unplug the dryer power cord or disconnect
the dryer at the household distribution panel by removing the fuse or switching off the
circuit breaker. Reach above dryer opening from inside the drum. Remove the bulb and
replace with the same size bulb.
Drum Lamp (Not all features are on all models)
Sensor Dry
(Not all features
are on all models)
Sensor Dry
This feature is active in all cycles except
Timed Dry, Warm Up and Air Fluff.
The Sensor Dry provides greater drying
accuracy than standard machines, resulting
in shorter dry times and better clothes
care. As the clothes tumble, they touch a
moisture sensor. The sensor will stop the
heating cycle as soon as the clothes have
reached the selected dryness.
This dryer will adjust the initial estimated
drying time of the sensor dry cycles as it
“learns” its installation and usage profile.
Please allow several weeks for the dryer to
customize itself to “you”.
Drying Rack (Not all features are on all models)
A handy drying rack may be used for drying
delicate items such as washable sweaters.
Hook the rack over the lint filter so
the rack extends into the dryer drum.
NOTE:
The drying rack must be used with the
Timed Cycle.
Do not use this drying rack when there
are other clothes in the dryer.
Alloy Steel Drum (Not all features are on all models)
The alloy steel used to make the
dryer drum provides the highest reliability
available in a GE dryer. If the dryer drum
should be scratched or dented during normal
use, the drum will not rust or corrode. These
surface blemishes will not affect the function
or durability of the drum.
About the dryer features.

8
Machine
wash
cycle Normal Permanent Press/
wrinkle resistant
Gentle/
delicate Hand wash Do not wash Do not wring
Water
temperature Hot
(50C/120F)
Warm
(40C/105F)
Cold/cool
(30C/85F)
WASH LABELS
Tumble
dry
Dry Normal Permanent Press/
wrinkle resistant Gentle/
delicate Do not tumble dry
Do not dry
(used with
do not wash)
Heat
setting
High Medium Low No heat/air
Special
instructions Line dry/
hang to dry Drip dry Dry flat In the shade
DRY LABELS
Bleach
symbols Any bleach
(when needed) Only non-chlorine bleach
(when needed)
Do not bleach
BLEACH LABELS
About loading and using the dryer.
Always follow the fabric manufacturer’s care label when laundering.
Sorting and Loading Hints
As a general rule, if clothes are sorted properly for
the washer, they are sorted properly for the dryer.
Do not add fabric softener sheets once the load
has become warm. They may cause fabric
softener stains. Bounce®Fabric Conditioner
Dryer Sheets have been approved for use in all
GE Dryers when used in accordance with the
manufacturer’s instructions.
Do not overload. This wastes energy and causes
wrinkling.
Do not dry the following items: fiberglass items,
woolens, rubber-coated items, plastics, items with
plastic trim and foam-filled items.
Care and Cleaning of the Dryer
The Exterior: Wipe or dust any spills or washing
compounds with a damp cloth. Dryer control
panel and finishes may be damaged by some
laundry pretreatment soil and stain remover
products. Apply these products away from the
dryer. The fabric may then be washed and dried
normally. Damage to your dryer caused by these
products is not covered by your warranty.
The Lint Filter: Clean the lint filter before each use.
Remove by pulling straight up. Run your fingers
across the filter. A waxy buildup may form on the
lint filter from using dryer added fabric softener
sheets.
To remove this buildup, wash the lint screen in
warm, soapy water Dry thoroughly and replace.
Do not operate the dryer without the lint filter in
place
Vacuum the lint from the dryer lint filter area if you
notice a change in dryer performance
Stainless Steel: To clean stainless steel surfaces,
use a damp cloth with a mild, non-abrasive cleaner
suitable for stainless steel surfaces. Remove the
cleaner residue, and then dry with a clean cloth.
Dryer Interior and Duct:The interior of the appliance
and exhaust duct should be cleaned once a year by
qualified service personnel.
The Exhaust Duct: Inspect and clean the exhaust
ducting at least once a year to prevent clogging.
A partially clogged exhaust can lengthen the
drying time.
Follow these steps:
1Turn off electrical supply by disconnecting
the plug from the wall socket.
2Disconnect the duct from the dryer.
3Vacuum the duct with the hose attachment
and reconnect the duct.
The Exhaust Hood: Check from the outside that
the flaps of the hood move freely when operating.
Make sure that there is not wildlife (birds, insects,
etc.) nesting inside the duct or hood.
Fabric Care Labels
Below are fabric care label “symbols” that affect the clothing you will be laundering.
Machine
wash
cycle Normal Permanent Press/
wrinkle resistant
Gentle/
delicate Hand wash Do not wash Do not wring
Water
temperature Hot
(50C/120F)
Warm
(40C/105F)
Cold/cool
(30C/85F)
WASH LABELS
Tumble
dry
Dry Normal Permanent Press/
wrinkle resistant Gentle/
delicate Do not tumble dry
Do not dry
(used with
do not wash)
Heat
setting
High Medium Low No heat/air
Special
instructions Line dry/
hang to dry Drip dry Dry flat In the shade
DRY LABELS
Bleach
symbols Any bleach
(when needed) Only non-chlorine bleach
(when needed)
Do not bleach
BLEACH LABELS
About loading and using the dryer.
Always follow the fabric manufacturer’s care label when laundering.
Sorting and Loading Hints
As a general rule, if clothes are sorted properly for
the washer, they are sorted properly for the dryer.
Do not add fabric softener sheets once the load
has become warm. They may cause fabric
softener stains. Bounce®Fabric Conditioner
Dryer Sheets have been approved for use in all
GE Dryers when used in accordance with the
manufacturer’s instructions.
Do not overload. This wastes energy and causes
wrinkling.
Do not dry the following items: fiberglass items,
woolens, rubber-coated items, plastics, items with
plastic trim and foam-filled items.
Care and Cleaning of the Dryer
The Exterior: Wipe or dust any spills or washing
compounds with a damp cloth. Dryer control
panel and finishes may be damaged by some
laundry pretreatment soil and stain remover
products. Apply these products away from the
dryer. The fabric may then be washed and dried
normally. Damage to your dryer caused by these
products is not covered by your warranty.
The Lint Filter: Clean the lint filter before each use.
Remove by pulling straight up. Run your fingers
across the filter. A waxy buildup may form on the
lint filter from using dryer added fabric softener
sheets.
To remove this buildup, wash the lint screen in
warm, soapy water Dry thoroughly and replace.
Do not operate the dryer without the lint filter in
place
Vacuum the lint from the dryer lint filter area if you
notice a change in dryer performance
Stainless Steel: To clean stainless steel surfaces,
use a damp cloth with a mild, non-abrasive cleaner
suitable for stainless steel surfaces. Remove the
cleaner residue, and then dry with a clean cloth.
Dryer Interior and Duct:The interior of the appliance
and exhaust duct should be cleaned once a year by
qualified service personnel.
The Exhaust Duct: Inspect and clean the exhaust
ducting at least once a year to prevent clogging.
A partially clogged exhaust can lengthen the
drying time.
Follow these steps:
1Turn off electrical supply by disconnecting
the plug from the wall socket.
2Disconnect the duct from the dryer.
3Vacuum the duct with the hose attachment
and reconnect the duct.
The Exhaust Hood: Check from the outside that
the flaps of the hood move freely when operating.
Make sure that there is not wildlife (birds, insects,
etc.) nesting inside the duct or hood.
Fabric Care Labels
Below are fabric care label “symbols” that affect the clothing you will be laundering.

9
Correct
Venting
Incorrect
Venting
For the best drying performance, the dryer needs to be properly vented. The dryer
will use more energy and run longer if it is not vented to the below specifications.
Carefully follow the details on Exhausting in the Installation Instructions.
Use only rigid metal 4” diameter ductwork inside the dryer cabinet. Use only rigid metal or
UL listed flexible metal 4” diameter ductwork for exhausting to the outside.
Do not use plastic or other combustible ductwork.
Use the shortest length possible.
Do not crush or collapse.
Avoid resting the duct on sharp objects.
Venting must conform to local building codes.
About venting the dryer. GEAppliances.ca
- Fire Hazard
WARNING
This dryer MUST be exhausted to the outdoors.
Use only 4” rigid metal ducting for the home exhaust duct.
Use only 4” rigid metal or UL-listed dryer transition duct to connect the dryer
to the home exhaust.
DO NOT use a plastic vent.
DO NOT exhaust into a chimney, kitchen exhaust, gas vent, wall, ceiling,
attic, crawl space, or concealed space of a building.
DO NOT install a screen in or over the exhaust duct.
DO NOT use duct longer than specified in the exhaust length table.
Failure to follow these instructions can result in death or fire.
11.7”
Venting
location
4
.5” to 4.7”

10
Troubleshooting Tips
Save time and money! Review the charts on the following pages,
Before you call for service…
Problem Possible Causes What To Do
Dryer doesn’t start Dryer is unplugged Make sure the dryer plug is pushed completely into
the outlet.
Fuse is blown/circuit breaker Check the house fuse/circuit breaker box and replace
is tripped fuse or reset breaker. NOTE: Most electric dryers use
two fuses/breakers.
Dryer doesn’t heat Fuse is blown/circuit breaker is Check the house fuse/circuit breaker box and replace
tripped; the dryer may tumble both fuses or reset both breakers. Your dryer may tumble
but not heat if only one fuse is blown or one breaker is tripped.
Gas service is off Make sure gas shutoff at dryer and main shutoff are
fully open.
No heat temperature Select another heat setting.
selected
Dryer shakes or Some shaking/noise is normal. Move dryer to an even floor space, or adjust leveling legs
makes noise Dryer may be sitting unevenly as necessary until even.
Greasy spots on clothes Improper use of fabric softener Follow directions on fabric softener package.
Drying dirty items Use your dryer to dry only clean items. Dirty items can
with clean ones stain clean items and the dryer.
Clothes were not Sometimes stains which cannot be seen when the clothes
completely clean are wet appear after drying. Use proper washing procedures
before drying.
Lint on clothes Lint filter is full Clean lint screen before each load.
Improper sorting Sort lint producers (like chenille) from lint collectors
(like corduroy).
Static electricity can attract lint See suggestions in this section under Static.
Overloading Separate large loads into smaller ones.
Paper, tissue, etc., left in pockets Empty all pockets before laundering clothes.
Static occurs No fabric softener was used Try a fabric softener.
Bounce®Fabric Conditioner Dryer Sheets have been
approved for use in all GE Dryers when used in accordance
with the manufacturer’s instructions.
Over-drying Try a fabric softener.
Adjust setting to Less Dry or Damp Dry.
Synthetics, permanent press Try a fabric softener.
andblendscancausestatic
Inconsistent Type of heat Automatic drying times will vary according to the type
drying times of heat used (electric, natural or LP gas), size of load,
types of fabrics, wetness of clothes and condition of
exhaust ducts.
The Dry dryness level Load consists of a mixture When combining heavy and light fabrics in a load,
was chosen but load is of heavy and light fabrics choose More Dry if you are using a sensor cycle.
still damp
Exhaust system is blocked Inspect and clean exhaust system.
or visit GEAppliances.ca. You may not need to call for service.

11
Before you call for service… GEAppliances.ca
Problem Possible Causes What To Do
Clothes take too long Improper sorting • Separate heavy items from lightweight items (generally,
to dry a well-sorted washer load is a well-sorted dryer load).
Large loads of heavy fabrics • Large, heavy fabrics contain more moisture and take
(like beach towels) longer to dry. Separate large, heavy fabrics into smaller
loads to speed drying time.
Controls improperly set • Match control settings to the load you are drying.
Lint filter is full • Clean lint filter before every load.
Improper or obstructed • Check installation instructions for proper
ducting ducting/venting.
• Make sure ducting is clean, free of kinks and
unobstructed.
• Check to see if outside wall damper operates easily.
• Check the Installation Instructions to make sure the
dryer venting is correct.
Blown fuses or tripped • Replace fuses or reset circuit breakers. Since most dryers
circuit breaker use 2 fuses/breakers, make sure both are operating.
Overloading/combining loads • Do not put more than one washer load in the dryer at
a time.
Under-loading • If you are drying only one or two items, add a few items
to ensure proper tumbling.
Clothes are wrinkled Over-drying • Select a shorter drying time.
• Remove items while they still hold a slight amount of
moisture. Select a Less Dry or Damp Dry setting.
Letting items sit in dryer • Remove items when cycle ends and fold or hang
after cycle ends immediately.
Overloading • Separate large loads into smaller ones.
Clothes shrink Some fabrics will naturally shrink • To avoid shrinkage, follow garment care labels exactly.
when washed. Others can be
safely washed, but will shrink • Some items may be pressed back into shape after drying.
in the dryer • If you are concerned about shrinkage in a particular
item, do not machine wash or tumble dry it
Water seen on inside of Steam condenses on these • This is normal.
door and top of lint filter surfaces
when opening door after
steam cycle
Collars and waistbands The dryness monitor senses • C
Timed Dry to dry damp collars and waistbands. In the
future, when drying a load with collars and waistbands,
choose More Dry.
hoose Speed Dry (Not all features are on all models) or
still wet at end of cycle that the body of the clothes
is dry
Slight variation This is normal • Due to the metallic properties of paint used for this unique
in metallic color product, slight variations of color may occur due to
viewing angles and lighting conditions.

12
Before you call for service…
Problem Possible Causes What To Do
Small amount of water Inadequate load size for steam • If using the Steam Dewrinkle cycle, manually reduce
on floor in front of dryer cycle selected, excess steam time. If using the Steam Refresh cycle, add more
condenses inside cabinet and
leaks out
Water on floor in back Loose water hose connection to
of dryer valve
Hose missing rubber washer at • Install rubber washer provided with hose.
connection with valve
Water drips from door Steam condenses on inner door • This is normal.
when opened after
a Steam Cycle
Cannot see steam at Steam released at different • This is normal.
beginning of cycle time in cycle
Cannot see steam at any The steam nozzle might be •Call1 800 561 3344 to order nozzle replacement kit
time during the cycle clogged with debris from your WW03A00189 or to request a service technician to replace
water supply this for you.
Garments still wrinkled Too many garments • Load fewer garments; manually increase time.
after steam cycle (Not all
features are on all models)
Dryer continues to Extended/Dewrinkle Tumble •EnsureExtended/Dewrinkle Tumble option is not selected.
tumble after display was selected For the Steam Refresh cycle, Extended/Dewrinkle Tumble
says complete will automatically be turned on and cannot be turned off.
Garments are wet after Lint filter not clean • Clean lint filter
Steam cycle (Not all
features are on all models) Load is children/infant garments • Use the Steam Refresh cycle.
No numbers displayed Dryer is continuously • This is normal. When the dryer senses a low level of
during cycle, only lights monitoring the amount of moisture in the load, the dryer will display the dry time
moisture in the clothes remaining.
Time Remaining The estimated time may change •Thisisnormal.
jumped to a when a smaller load than usual
lower number is drying
Dryer is running but The Extended/Dewrinkle • This is normal. During Extended/Dewrinkle Tumble, the
00 is displayed in Tumble option was chosen time remaining is not displayed. The extended tumbling
Time Remaining option lasts approximately 60 minutes; dewrinkle 60 minutes.
Clothes are still wet The door was opened mid-cycle. • A dry cycle must be re-selected each time a new load
and dryer shuts off The load was then removed from is put in.
after a short time the dryer and a new load put in
without selecting a new cycle
Small load • When drying 3 items or less, choose Speed Dry (Not all
features are on all models) or Timed Dry.
Load was already dry except • Choose Speed Dry or Timed Dry to dry damp collars
for collars and waistbands and waistbands. In the future, when drying a load with
collars and waistbands, choose More Dry or Sanifresh.
Dryer is not level • Move dryer to an even floor space or adjust leveling legs
as necessary until even.

13
GE Dryer Warranty.
What GE Will Not Cover:
Service trips to your home to teach you how
to use the product.
Improper installation, delivery or maintenance.
Failure of the product if it is abused, misused, or
used for other than the intended purpose or used
commercially.
Replacement of the light bulb.
Replacement of house fuses or resetting
of circuit breakers.
Damage to the product caused by accident, fire, floods
or acts of God.
Incidental or consequential damage caused by possible
defects with this appliance.
Damage caused after delivery.
Product not accessible to provide required service.
Defects or damage due to operation in freezing
temperatures.
Products which are not defective or broken, or which are
working as described in the Owner’s Manual.
WARRANTOR: MC COMMERCIAL INC., BURLINGTON, ON L7R 5B6
Staple your receipt here.
Proof of the original purchase
date is needed to obtain
support under the warranty.
EXCLUSION OF IMPLIED WARRANTIES³Your sole and exclusive remedy is product repair as provided in this Limited
Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular
purpose, are limited to one year or the shortest period allowed by law.
For The Period Of: GE Will Replace:
One Year Any part of the dryer which fails due to a defect in materials or workmanship. During this
From the date of the limited one-year warranty, GE will also provide, free of charge, all labor and related service costs
original purchase to replace the defective part.
All warranty support provided by our authorized service centers.
To schedule service, on-line, 24 hours a day, visit us at
GEAppliances.ca or call 1 800.561.3344 during normal business
hours. Please have serial number and model number available
when calling for service.
This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada for
home use within Canada. If the product is located in an area where service by a GE Authorized Servicer is not available,
you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service
location.
Some provinces do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from province to province. To know what your
legal rights are, consult your local or provincial consumer affairs office.

14
Consumer Support.
GE Appliances Website GEAppliances.ca
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts or even schedule service on-line.
Schedule Service GEAppliances.ca
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at your
convenience 24 hours any day of the year! Or call 1 800.561.3344 during normal business hours..
Real Life Design Studio GEAppliances.ca
GE supports the Universal Design concept³products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen design
ideas for people with disabilities, check out our Website today. Call 1 800.561.3344.
Extended Warranties
Consult your local listings for the nearest extended warranty provider.
Parts and Accessories GEAppliances.ca
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes.
Visit your local authorized GE parts distributor or call 1 800.661.1616.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may
cause unsafe operation.
Contact Us GEAppliances.ca
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: Director, Consumer Relations, MC Commercial
Suite 310, 1 Factory Lane
Moncton, N.B. E1C 9M3
Register Your Appliance GEAppliances.ca
Register your new appliance on-line³at your convenience!Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.