GE DSXH43EFWW Manual

DSXH43EFWW
GE® Extra-Large 5.7 Cu. Ft. Capacity Frontload Electric Dryer
Dimensions and Installation Information (in inches)
Exhaust Options: Electric—4-way via rear, right, left
and bottom.
Circuit Requirements: Electric—An individual,
properly-grounded branch circuit, protected by a 30-
amp circuit breaker or a time-delay fuse, is required.
Electric Dryer Rating:
120/240V, 3-wire, 5600W, 24A
120/208V, 3-wire, 4400W, 22A
Note: Dryer wall outlet must be located within 36”
of service cord entry and accessible when dryer is
mounted in position.
Installation Information: For complete information,
see installation instructions packed with your dryer.
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
Specification Created 9/05 360426
SIDE VIEW
25-3/4
47-1/2
4-3/4
Optional
Vent Knockout
Door Open
90°
4-3/8
3/4
REAR VIEW
26-7/8
3-3/4
1
36
Under
Counter
34-5/8"
3/16"
Gas Pipe Connection
Electric
Connection
2-9/16
13-9/16
27" Min.
27" Min.
70-5/8
Note:
Closet Installation Requires Additional
Minimum Clearances:
A Minimum of 120 Square Inches of Opening,
Equally Divided at the Top and Bottom of
the Closet Door is Required.
Top of Dryer to Ceiling 15"
Back of Dryer to Wall 4"
Front of Dryer/Washer 1"
to Closet Door
27"
Min. 34-5/8"
Min.
Custom Sized
Countertop Required
54" Min.
SIDE VIEW
25-3/4
47-1/2
4-3/4
Optional
Vent Knockout
Door Open
90°
4-3/8
3/4
REAR VIEW
26-7/8
3-3/4
1
36
Under
Counter
34-5/8"
3/16"
Gas Pipe Connection
Electric
Connection
2-9/16
13-9/16
27" Min.
27" Min.
70-5/8
Note:
Closet Installation Requires Additional
Minimum Clearances:
A Minimum of 120 Square Inches of Opening,
Equally Divided at the Top and Bottom of
the Closet Door is Required.
Top of Dryer to Ceiling 15"
Back of Dryer to Wall 4"
Front of Dryer/Washer 1"
to Closet Door
27"
Min. 34-5/8"
Min.
Custom Sized
Countertop Required
54" Min.
R
Listed by
Underwriters
Laboratories

Dimensions and Installation Information (in inches)
Special Installation Requirements
Undercounter Installation
Accessory mounting kits are required for undercounter installation. To order,
call 1-800-848-7722.
Stacked Installation: Brackets for stacking dryer over washer are included with
the washer.
Alcove or Closet Installation:If your dryer is approved for installation in an
alcove or closet, it will be stated on a label on the dryer back. The dryer MUST
be exhausted to the outdoors. Minimum clearances between dryer cabinet and
adjacent walls or other surfaces are: 0" either side, 3" front and rear Minimum
vertical space from floor to overhead cabinets, ceilings, etc. is 52". Closet doors
must be louvered or otherwise ventilated and must contain a minimum of 60
sq. in. of open area equally distributed. If this closet contains both a washer
and a dryer, doors must contain a minimum of 120 sq. in. of open area equally
distributed. The closet should be vented to the outdoors to prevent gas pocketing
in case of a gas leak in the supply line. No other fuel-burning appliance shall be
installed in the same closet with the dryer.
Bathroom or Bedroom Installation: The dryer must be exhausted to the
outdoors. The installation must conform with the local codes, or in the absence
of local codes, with the National Fuel Gas Code, ANSI Z223.
Minimum Clearances other than Alcove or Closet Installations:
Minimum clearances to combustible surfaces: 0" both sides, 3" rear
511LF1
36"
25-3/4"
53-1/2"
511LF2
Washer
Top Sheet
Dryer
Top Sheet
Countertop
511LF3
14''
29'' 56''-60''
Lip on All Sides
3/4" High x 3/4" Wide
Max.
511LF4
70-5/8"
25-3/4"
26-3/4"
Free-Standing Installation Raised/ Built-in Installation
Stacked Installation
Undercounter Installation
Specification Created 9/05 360426
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
DSXH43EFWW
GE® Extra-Large 5.7 Cu. Ft. Capacity Frontload Electric Dryer

Best Performance
Maximum Length
of 4" Dia.
Rigid Metal Duct
Maximum Length
of 4" Dia.
Flexible Metal Duct
Number
of
90°
Turns
Exhaust Hood Type Exhaust Hood Type
A
4" Opening
B
2-1/2"
Opening
A
4" Opening
B
2-1/2"
Opening
Front Loading
Dryers
0
1
2
3
4
60 ft.
52 ft.
44 ft.
32 ft.
28 ft.
48 ft.
40 ft.
32 ft.
24 ft.
16 ft.
30 ft.
22 ft.
14 ft.
18 ft.
14 ft.
10 ft.
A
B
2-1/2
4
GE Dryer Vent
Dryer Exhausting Information – Metal Duct Only
For complete information, see installation instructions packed with your dryer.
Ducting Materials: For best performance, this dryer should be vented with 4” diameter all rigid
metal exhaust duct. If “all rigid metal” duct cannot be used, then “flexible all metal” venting can
be used, but it will reduce the maximum recommended duct length.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2. The maximum length of 4’ rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table. The maximum length for flexible ducts are less than for rigid duct.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Exhausting the dryer to the outside is strongly recommended to prevent large amounts of
moisture and lint from being blown into the room. Gas dryers or any dryer located in a closet
must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard
or moisture could cause damage. Never terminate the exhaust into a common duct or plenum
with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed Down.
Other terminations, such as louvered wall boxes, are acceptable provided they are equivalent
to a 4" opening dampered wall cap.
For more information on venting kits and accessories, please call 1-800-GE-CARES.
360426
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
DSXH43EFWW
GE® Extra-Large 5.7 Cu. Ft. Capacity Frontload Electric Dryer
Specification Created 9/05
R
Listed by
Underwriters
Laboratories

Specification Created 9/05 360426
Features and Benefits
• Extra-Large (5.7 cu. ft.) Capacity
• Tumble Drying
• 4 Temperature Options: Regular/Cottons, Medium/Permanent Press,
Low/Delicates and Air Fluff/No Heat (Cool Down)
• 1 Time Dry Cycle
• 2 Auto Dry Cycles: Cottons and Easy Care
• Adjustable End-of-Cycle Signal
• Quick Clean Lint Screen
• Drying Rack
• Spill-Saver Top
• Interior Dryer Light
• Dura Finish Top and Drum
• Leveling Legs
• Heavy Duty Suspension System
• 4 Exhaust Option
• Reverse-A-Door
• 100% Front Serviceable
• Model DSXH43EFWW - White on white (Electric)
• Model DSXH43GFWW - White on white (Gas)
DSXH43EFWW
GE® Extra-Large 5.7 Cu. Ft. Capacity Frontload Electric Dryer