GE Profile Harmony DPGT750EC Manual

For answers to your Monogram,® GE Profile™or
GE®appliance questions, visit our website at
ge.com or call GE Answer Center®service,
800.626.2000.
DPGT750EC
GE Profile™Harmony™King-size 7.3 Cu. Ft. Capacity Electric Dryer
Listed by
Underwriters
Laboratories
Specification Revised 9/07
22-1/2
Side View Rear View
GE Profile Harmony Dryer
29
26-1/2
3-1/2 36
43
3
2-1/2 3-1/2
13
27
Exhaust Options: 4-way via rear, right, left
and bottom. Dryer is shipped exhausted
to the rear. Right, left or bottom exhaust
requires a conversion kit.
NEMA Receptable codes:
3-prong dryer cord/30A/4' long (cat #WX9X2)
is for NEMA10-30R receptable
4-prong dryer cord?30A/4' ong (cat #WX9X18)
is for NEMA14-30R receptacle
Circuit Requirements: An individual properly-
grounded branch circuit, protected by a 30
amp circuit breaker or a time-delay fuse is
required.
Electric Dryer Rating: 240V, 6000W, 28.5A,
60Hz
Note: Dryer wall outlet must be located within
36" of service cord entry and accessible when
dryer is mounted in position.
Installation Information: For complete
information, see installation instructions
packed with your dryer.
Dimensions and Installation Information (in inches)
270185

270185
DPGT750EC
GE Profile™Harmony™King-size 7.3 Cu. Ft. Capacity Electric Dryer
Specification Revised 9/07
For complete information, see installation instructions packed with your dryer.
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all rigid metal
exhaust duct. If “all rigid metal” duct cannot be used, then “flexible all metal” venting
can be used, but it will reduce the maximum recommended duct length.
Exhaust Length Calculation:
1.Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2.The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated
is shown in the table. The maximum length for flexible ducts are less than for rigid
duct. A turn of 45° or less may be ignored. Two 45° turns within the duct length should
be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Exhausting the dryer to the outside is strongly recommended to prevent large
amounts of moisture and lint from being blown into the room. Gas dryers or any dryer
located in a closet must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any
enclosed house floor (crawl space), or into an attic, since the accumulated lint could
create a fire hazard or moisture could cause damage. Never terminate the exhaust
into a common duct or plenum with a kitchen exhaust, since the combination of lint
and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts,
bird nesting, etc. The wall cap must also be located at least 12" above the ground or
any other obstruction with the opening pointed down.
Other terminations, such as louvered wall boxes, are acceptable provided they are
equivalent to a 4" opening dampered wall cap.
Dryer Elbow Kit, Pub. No. 14-A003 is available at additional cost. For use with side or
bottom exhaust options.
For more information on venting kits and accessories, please call 1-800-GE-CARES.
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label
on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side; 3" front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
• Closet doors must be louvered or otherwise ventilated and must contain a minimum
of 60 sq. in. of open area equally distributed. If this closet contains both a washer and
a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes,
with the National Fuel Gas Code, ANSI Z223.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces are: 0" both sides; 3" rear
Dryer Exhausting Information: Use metal duct only, vertical and horizontal ducting.

Specification Revised 9/07
P
O
W
E
R
M
Y
C
Y
C
L
E
S
H
E
L
P
B
A
C
K
H
O
M
E
TOUCH TO SELECT�
Sensor
BY
FABRIC
SPECIAL�
CYCLES TIMED DRY
BY
GARMENT
ST
ART�
STOP
DPGT750ECWW/GCWW
Features and Benefits
• Receives Load Information Electronically from the Washer (WPGT9350)
• King-size 7.3 Cu. Ft. Capacity Dryer with Stainless Steel Drum and
Deluxe Dryer Rack
• DuoDry™System Quickly and Consistently Dries All Types of Clothes
• LCD Electronic Controls with Time Display Status Lights and Cycle
Countdown with LCD Indicators
• Variable Heater Delivers Constant Heat, with No On-off Cycling, for
Optimal Drying Results
• Adaptive Venting System Delivers Exceptional Drying Performance
• Delicate Cycle with Extra Low Setting Maintains an Average Fabric
Temperature of 125°F to Protect Fine Handwashables
• Reversible Washer and Dryer Control Panels Can be Easily Interchanged
Without Any Loss of Function, Allowing Installation Flexibility
• Multiple Dry Cycles with 6 Custom Cycles and Adaptive Logic System™
• Dual Electronic Thermistors
• Dual Motors
• Dryer Interior Light
• Model DPGT750ECPL –Dark platinum
• Model DPGT750ECWW –White on white
DPGT750EC
GE Profile™Harmony™King-size 7.3 Cu. Ft. Capacity Electric Dryer
270185