GE Monogram ZUG30 User manual

Installation Instructions – ZUG30 Heater Kit/Cover
TO BE USED WITH HOUSEHOLD REFRIGERATORS
30" BUILT-IN
BOTTOM-FREEZER, 2 DRAWER
ALL REFERENCES TO ASSEMBLY ARE FROM THE FRONT OF THE UNITS
PARTS PROVIDED:
Installation Instructions (1)
Heater (1)
Transformer (1)
Plastic Cover (1)
Brackets (2)
Tools Required:
#2 Phillips Head Screw Driver
Step Ladder
Open Wrench Set
5 mm. Allen Wrench
IMPORTANT SAFETY NOTICE:
This kit is to be installed by a qualied service technician only. Any attempt to repair a major appliance may result in
personal injury and property damage. Neither the manufacturer nor the seller can be responsible for the interpretation
of this information or assume any liability in connection with its use.
197D9290P001 31-45446-1 05-12 GE
Unit 1 - Spacer Clips Installed
Unit 1 Unit 2
Unit 2 - Heater Installed
Spacer Clips (8)
Strain Relief (1)
Screw, 4.8 x 13 (4)
Bolt, M4 x 18 (2)
Nut, M4 (2)
Washer, star (4)
Bolt, M6 x 45 (3)
Nut, M6 (3)
Washer, at (6)
Wiring 'Y' Splitter (1)
NOTE: WHILE PERFORMING INSTALLATIONS
DESCRIBED IN THIS BOOK, SAFETY GLASSES OR
GOGGLES SHOULD BE WORN.
PPE Required:
Safety Glasses
Safety Gloves
BEFORE YOU BEGIN
Read these instructions
completely and carefully.
Disconnect power to the appliance before beginning installation.
Do not operate the refrigerator until the installation is complete.
WARNING
WARNING
This refrigerator is top heavy and must be handled with care.
Failure to do so can result in the unit tipping over and re
sult in death or serious injury.
Do not cut lower banding on units.
Do not remove foam base pad from front of units.
STOP

1. This heater kit will only t two units, if the doors face each other when opened. Door swing of unit 1 must
be switched from right hand swing to left hand swing. Refer to Installation Instructions 31-46542 for proper
procedure and safety measures.
2. On sides of refrigerators, remove white stickers from top and center location, to reveal holes in the case. Remove
any labels from sides of refrigerators and clean the surfaces.
3. Attach spacer clips to the inner side wall of Unit 1. Line up holes in Spacer Clips 1 and 4 with holes in case. Attach
clips 2 and 3 evenly spaced between 1 and 4. Note that clips 2 and 3 are dierent that the six other clips. It is very
important that you use clips 2 and 3 in those locations only. Clip 6 attaches on the bottom front corner, along the
front edge of Unit 1, same as clips 1 and 4. Clip 5 spaced evenly between clip 4 and 6. Clip 7 attaches to the top,
rear corner of Unit 1. Orientation is not critical. Clip 8 is attached in a later step.
Unit 1 Unit 2
Required Door Swing
(view from above)
Unit 1 Unit 2
Spacer Clips
Unit 1 Unit 2
1
1
77
2
2
3
3
44
5
5
66
8
8
2
1,4-8
Spacer Clips 2,3

4. On Unit 2, use top and center holes to locate the foil heater. There is a hole in the foil heater. This lines up with the
hole at the center of the case. The "V" notch at the top of the heater, lines up with the top hole in the side of the
case. Remove paper backing from heater and carefully apply heater using these two holes as guides.
5. In front of cabinet enclosure, move units next to each other, whith holes lined up. Make sure heater wire is dressed
towards front of units for use in a later step. Tape heater lead wires to side of Unit 2 so that leads are sticking out
the front, below clip 6, and easily reached for use in a later step. Using bolts, washers and nuts, join the two units
together at the front - top and center. Tightened bolts until spacer clips touch Unit 2.
Rear
Front
Unit 2
Unit 1 Unit 2
Heater lead wires
3

4
6. Attach joining brackets to rear of reach unit, using screws provided with kit, add spacer between brackets. Join
with bolt, washers and nut. Do not cut lower banding strap during this step.
7. Refer to Installation Instructions 31-46542 included with the units. Connect water lines to units, plug units into
electrical outlets, push units into cabinet enclosure and fasten to anti-tip brackets.
8. After fastening the anti-tip brackets to each unit, cut lower banding straps on Units 1 and 2 and remove foam
base pad from front of units.
9. Next, the heater will be joined to the wiring of Unit 2. The heater is a low voltage, DC type heater, so this step
consists of adding a transformer between line voltage and the heater, and the steps needed to mount and wire
the transformer.
Remove toekick and air vent cover from front of Unit 2 by removing four Phillips head screws.
Vent Cover
Metal Plate
Toekick

5
Fasten heater leads to open slot in vent cover, using the strain relief provided with the kit.
Vent cover
Strain relief
Heater leads
Locate the vertical, metal plate behind the vent cover. There are two holes in the plate for mounting the transformer.
Locate the transformer on the plate and attach using bolts, nuts and washers supplied.
Metal plate
Transformer

NOTE: PRODUCT IMPROVEMENT IS A CONTINUING ENDEAVOR AT
GENERAL ELECTRIC. THEREFORE, MATERIALS, APPEARANCE AND
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
GE Appliances & Lighting
General Electric Company
Louisville, KY 40225
GEAppliances.com
Attach heater lead wires to transformer lead wires (blue and green leads connect to the heater).
Heater leads
From Transformer
Strain relief
Trim cover snaps into the front six spacer clips
10. Reattach front toeckick and air vent cover.
11. Attach front trim piece, provided in kit, along length of units from top to bottom, by snapping into the clips that
were attached in step 3).
Vent Cover
Unplug main power cord
In front of unit, unplug the power cord and replace with the 'Y' splitter supplied in the kit. On the ends of the splitter,
plug in the transformer (black and white leads) and the power cord plug.
'Y' splitter
To transformer
Main power cord