GE Appliances CV936 Original instructions

Range Hoods
Vented
350A4502P550 08-07 ATS
Safety Instructions . . . . . . . . . 2, 3
Operating Instructions
Light Controls . . . . . . . . . . . . . . . .4
Vent Controls . . . . . . . . . . . . . . . .4
Care and Cleaning
Grease Filters . . . . . . . . . . . . . . . .5
Hood Lights . . . . . . . . . . . . . . . . .6
Hood Surfaces . . . . . . . . . . . . . . . .5
Stainless Steel Surfaces . . . . . . . . .5
Installation Instructions . . .7–18
Troubleshooting Tips . . . . . . . .20
Consumer Support
Consumer Support . . . Back Cover
Product Registration . . . . . .21, 22
Warranty . . . . . . . . . . . . . . . . . . . 23
Write the model and serial
numbers here:
Model # ________________
Serial # ________________
You can find them on a label
on the inside of the hood.
JV936
CV936
Owner’s Manual and
Installation Instructions
www.GEAppliances.ca

SAFETY PRECAUTIONS
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING – TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
A. Use this unit only in the manner intended
by the manufacturer. If you have questions,
contact the manufacturer.
B. Before servicing or cleaning unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from
being switched on accidentally. When the
service disconnecting means cannot be locked,
securely fasten a prominent warning device,
such as a tag, to the service panel.
C. Do not use this unit with any solid-state speed
control device.
D. This unit must be grounded.
CAUTION – For general ventilating use only.
Do not use to exhaust hazardous or explosive
materials and vapors.
CAUTION – To reduce risk of fire and to
properly exhaust air, be sure to duct air outside.
Do not vent exhaust air into spaces within walls or
ceilings or into attics, crawl spaces, or garages.
WARNING – TO REDUCE THE RISK OF
INJURY TO PERSONS IN THE EVENT OF A RANGE
TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
A. SMOTHER FLAMES with a close-fitting
lid, cookie sheet, or metal tray, then turn off
the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out
immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN—
You may be burned.
C. DO NOT USE WATER, including wet
dishcloths or towels—a violent steam
explosion will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC
extinguisher, and you already know how
to operate it.
2. The fire is small and contained in the
area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to
an exit.
* Based on “Kitchen Fire Safety Tips” published
by NFPA.
Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions
Care and Cleaning
2

Consumer Support
Troubleshooting TipsOperating InstructionsSafety Instructions Care and Cleaning
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
READ AND SAVE THESE INSTRUCTIONS
SAFETY PRECAUTIONS
www.GEAppliances.ca
WARNING – TO REDUCE THE RISK OF
A RANGE TOP GREASE FIRE:
A. Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on
low or medium settings.
B. Always turn hood ON when cooking at high
heat or when cooking flaming foods.
C. Clean ventilating fans frequently. Grease
should not be allowed to accumulate on fan
or filter.
D. Use proper pan size. Always use cookware
appropriate for the size of the surface element.
WARNING – TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance
with all applicable codes and standards,
including fire-rated construction.
B. Sufficient air is needed for proper
combustion and exhausting of gases through
the flue (chimney) of fuel burning equipment
to prevent back drafting. Follow the heating
equipment manufacturer’s guideline and
safety standards such as those published by
the National Fire Protection Association
(NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
C. When cutting or drilling into wall or ceiling,
do not damage electrical wiring and other
hidden utilities.
D. Ducted fans must always be vented to the
outdoors.
WARNING – TO REDUCE THE RISK OF FIRE,
USE ONLY METAL DUCTWORK.
■Do not attempt to repair or replace any
part of your hood unless it is specifically
recommended in this guide. All other servicing
should be referred to a qualified technician.
3

Using the hood controls.
Throughout this manual, features and appearance may vary from your model.
FAN Control
Turn the FAN speed control to LO, MED LO,
MED HI or HI, as needed.
Continuous use of the fan system while cooking
helps keep the kitchen comfortable and less
humid. It also reduces cooking odors and soiling
moisture that create a frequent need for
cleaning.
NOTE: When the fan is operating on the LO setting,
it will be very quiet. Always make sure that the fan
is turned OFF when you are finished in the kitchen.
LIGHT Control
Turn the LIGHT control to HI for bright light
while cooking. Turn to NITE for use as a night
light.
Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions
Care and Cleaning
4

Care and cleaning of the vent hood. www.GEAppliances.ca
Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the
vent hood.
The hood has 2 metal reusable
grease filters.
The metal filters trap grease
released by foods on the cooktop.
They also help prevent flaming
foods on the cooktop from
damaging the inside of the hood.
For this reason, the filters must
ALWAYS be in place when the
hood is used. The grease filters
should be cleaned once a month,
or as needed.
To clean the grease filters, soak
them and then swish them around
in hot water and detergent.
Don’t use ammonia or ammonia
products because they will darken
the metal. Do not use abrasives or
oven cleaners. Light brushing can
be used to remove embedded dirt.
Rinse, shake and let them dry
before replacing. They may
also be cleaned in an automatic
dishwasher.
To remove:
Grasp the filter handle and pull it
up, forward and out.
To replace:
Hold the filter at the bottom
with the handle.
Place the top end of the filter
against the inside front of the
hood.
Slide it up until it stops and
push the bottom end back
until it snaps into place.
Reusable Metal Grease Filters
To clean the hood surface, use
a hot, damp cloth with a mild
detergent suitable for painted
surfaces. Use a clean, hot, damp
cloth to remove soap. Dry with
a dry, clean cloth.
Do not use steel-wool pads or
other abrasive cleaners. They will
scratch the surface.
Painted Surfaces (on some models)
If it ever becomes necessary to
replace the metal grease filters, they
may be ordered from your GE supplier.
Consumer Support
Troubleshooting TipsOperating InstructionsSafety Instructions Care and Cleaning
5
Heavy-duty commercial filters may
also be used in place of the filters.
For 30” (76.2 cm) hoods,
order Kit no. JXBF30SS .
For 36” (91.4 cm) hoods,
order Kit no. JXBF36SS .
To order, call 1.800.661.1616
Do not use a steel-wool pad; it will
scratch the surface.
Shake bottle well.
Place a small amount of
CERAMA BRYTE®Stainless
Steel Cleaning Polish and
Conditioner on a dry cloth
or dry paper towel.
Clean a small area
(approximately 8” x 8” or
20.3 x 20.3 cm), rubbing with
the grain of the stainless steel if
applicable.
Dry and buff with a clean, dry
paper towel or soft cloth.
Repeat as necessary.
Stainless Steel Surfaces (on some models)
To order:
To order CERAMA BRYTE
®
Stainless Steel
Cleaning Polish and Conditioner, please call
our toll-free number:
National Parts
Center . . . . . . . . . . . 1.800.661.1616
www.GEAppliances.ca
CERAMA BRYTE
®
Stainless Steel Cleaning
Polish and Conditioner . . . # PM10X313

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions
Care and Cleaning
6
Care and cleaning of the vent hood.
Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of
the vent hood.
Hood Lights
NOTE: The glass cover should be removed
only when cold. Wearing latex gloves may
offer a better grip.
CAUTION: Before replacing your
light bulb, disconnect the electrical power
to the hood at the main fuse or circuit
breaker panel.
Be sure to let the light cover and bulb cool
completely.
For your safety, do not touch a hot bulb
with bare hands or a damp cloth.
To remove:
Turn the glass cover counterclockwise
until the glass cover clears the socket.
Using gloves or a dry cloth, remove
the bulb by pulling it straight out.
To replace:
Use a new 12-volt, 20-watt (maximum)
Halogen bulb for a G-4 base.
Using gloves or a dry cloth, remove
the new bulb from its packaging.
NOTE: Do not touch the new halogen bulb
with bare fingers. Touching the bulb with
bare fingers will significantly reduce the
life of the bulb.
Push the bulb straight into the
receptacle all the way.
Place the glass cover onto the socket
and turn clockwise until secure.
For improved lighting, clean the glass
cover frequently using a damp cloth.
This should be done when the hood
is completely cool.
Reconnect electrical power to
the hood.
Bulb
Socket
Glass cover
Receptacle
Use gloves
or cloth
Receptacle

BEFORE YOU BEGIN
7
Installation Range Hood
Instructions
Read these instructions completely and carefully.
•IMPORTANT – Save these
instructions for local inspector’s use.
•IMPORTANT – Observe all
governing codes and ordinances.
•Note to Installer – Be sure to leave these
instructions with the Consumer.
•Note to Consumer – Keep these instructions
for future reference.
•Skill level – Installation of this vent hood requires
basic mechanical and electrical skills.
•Completion time – 1 to 3 hours
•Proper installation is the responsibility of the
installer.
•Product failure due to improper installation is not
covered under the Warranty.
18"
21" 35-7/8"
12"
18"
21" 29-7/8"
12"
PRODUCT DIMENSIONS
WARNING – Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
FOR YOUR SAFETY:
Questions? Call 1-800-561-3344 or Visit our Website at: www. GEAppliances.ca
Due to the weight and size of these vent hoods and to
reduce the risk of personal injury or damage to the
product, TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
CAUTION:
1 Ft = 0.3 m
1” = 2.5 cm
30” Models
Requires a 30” Wide Opening
36” Models
Requires a 36” Wide Opening

These vent hoods are designed to be installed onto a
wall. They may be installed beneath a soffit or cabinet.
• Install these hoods 24” Min. to 36” Max above the
cooking surface.
INSTALLATION CLEARANCES
24" MIN.
36" MAX.
Installation Instructions
1 Ft = 0.3 m
1” = 2.5 cm
In this installation the ductwork running from the top
of the hood will be concealed in the soffit or upper
cabinetry.
For this installation, a decorative duct cover is available
to conceal the ductwork running from the top of the
hood. Use of the duct cover requires special
consideration to the installation height above the
countertop. See page 12 for details.
SOFFIT
WALL MOUNT INSTALLATION
SOFFIT INSTALLATION
24" MIN.
36" MAX.
OPTIONAL ACCESSORIES
Duct Cover
A Decorative duct cover is available to accommodate 8
to 10 ft. ceiling heights. The duct cover will expand
from 12” Min. or 24” to 34” Max. height.
• The duct cover conceals the ductwork running from
the top of the hood to the ceiling.
• The duct cover accessory fits both 30” and 36” wide
models. Order the duct cover accessory at the same
time as the vent hood. All accessories should be on
site at the time of hood installation.
Order the correct color to match your model:
JXCHBB - Black, JXCHWW - White,
JXCHCC - Bisque, JXCHSS - Stainless Steel.
2 Wood
Screws
4 Phillips Head
Screws
Ceiling Bracket
2 Baffle Filters
2 Phillips Head
Decorative Screws
2-Piece Duct Cover
With Ceiling Bracket
2 Drip Trays
2 Wall
Fasteners
2 Washers
Commercial Filter Kit
Use this kit to replace supplied filters.
JXBF30SS, Commercial Filter Kit for 30” wide models.
JXBF36SS, Commercial Filter Kit for 36” wide models.
Includes 2 commercial filters and 2 drip trays.
8

Ductwork Planning
• This hood may be vented vertically through upper
cabinets, soffit or ceiling. A duct transition piece is
supplied for vertical exhaust. Use locally supplied
elbows to vent horizontally through the rear wall.
See page 13.
• Determine the exact location of the vent hood.
• Use the shortest and straightest duct route possible.
For satisfactory performance, duct run should not
exceed 100 equivalent length for any duct
configurations.
• Refer to “Duct Fittings” chart to compute the
maximum permissible length for duct runs to the
outdoors.
• Use metal ductwork only.
• A transition piece for 7” round duct is supplied. Use 7”
round duct or you may use 3¼” x 12” rectangular.
• Install a wall cap or roof cap with damper at the
exterior opening. Order the wall or roof cap and any
transition needed in advance.
Kit - JXDW1
Order kit JXDW1 if your installation requires horizontal
ducting from the top of the hood through the back wall
and:
• You have an 8 ft. ceiling and need to use a JXCH
Series Chimney Cover, or
• You have a 12” cabinet or 12” soffit that the hood is to
be mounted beneath.
This kit provides a duct transition from 7” round to
3¼” x 10” rectangular for through-the-wall venting.
Wall Framing for Adequate Support
• This vent hood is heavy. Adequate structural support
must be provided. The hood must be secured to
vertical studs in the wall. See page 14.
• We strongly recommend that the vent hood with duct
cover be on site before final framing and wall
finishing. This will also help to accurately locate the
ductwork and electrical service.
ADVANCE PLANNING
Installation Instructions
1 Ft = 0.3 m
1” = 2.5 cm
DECORATIVE DUCT COVERS
A decorative duct cover is available to fit both model
widths. The duct cover conceals the ductwork running
from the top of the hood to the ceiling or soffit. The
duct cover will fit 8 ft. to 10 ft. ceiling heights. See page
12 for details.
9
Follow these guidelines for proper duct sizing in the
ducting charts.
DUCT FITTINGS
MAXIMUM DUCT LENGTH: 7” dia. duct, should not
exceed 100 equivalent feet.
025
50 75 100 125 150
600
500
400
300
200
Equivalent Length in Feet for 7” Round Duct
Air Volume in CFM
7” Round 90° Elbow = 8 ft. 7” Roof Cap = 30 ft.
DUCTING CHART - 30” and 36” Models
POWER SUPPLY
IMPORTANT - (Please read carefully)
WARNING:
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before
beginning installation.
Do not use an extension cord or adapter plug with this
appliance. Follow National electrical codes or prevailing
local codes and ordinances.
Electrical supply
This vent hood must be supplied with 120V, 60Hz, and
connected to an individual, properly grounded branch
circuit, and protected by a 15 or 20 amp circuit breaker
or time delay fuse.
• Wiring must be 2 wire with ground.
• If the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
• Route house wiring as close to the installation location
as possible in the ceiling, soffit or wall. See page 13 for
details.
• Connect the wiring to the house wiring in accordance
with local codes.
Grounding instructions
The grounding conductor must be connected to a
ground metal, permanent wiring system, or an
equipment-grounding terminal or lead on the hood.
WARNING:
The improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative if
you are in doubt whether the appliance is properly
grounded.

Installation Instructions
10
Use this chart to compute maximum
permissable lengths for duct runs to
outdoors.
Note: Do not exceed maximum permissable
equivalent lengths!
Maximum duct length:
100 foot for vent hoods.
Flexible ducting:
If flexible metal ducting is used, all
the equivalent feet values in the table
should be doubled. The flexible
metal duct should be straight and
smooth and extended as much as
possible.
Do NOT use flexible ducting.
Note: Any home ventilation system, such as a
ventilation hood, may interrupt the proper flow of
combustion air and exhaust required by fireplaces,
gas furnaces, gas water heaters and other
naturally vented systems. To minimize the chance
of interruption of such naturally vented systems,
follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by NFPA and ASHRAE.
DUCT FITTINGS
This Hood Must Use 7” Round
Duct. It Can Transition To
3¼” x 12” Duct
Kit - JXDW1
Order kit JXDW1 if your
installation requires horizontal
ducting from the top of the hood
through the backwall and:
• You have an 8 ft. ceiling and
need to use a JXCH Series
Chimney Cover, or
• You have a 12” cabinet or 12”
soffit that the hood is to be
mounted beneath.
This kit provides a duct transition
from 7” round to 3¼” x 10”
rectangular for through-the-wall
venting.
Using a smaller diameter duct
size will reduce performance *Actual length of straight duct plus duct fitting
equivalent. Equivalent length of duct pieces are
based on actual tests conducted by GE Evaluation
Engineering and reflect requirements for good
venting performance with any ventilation hood.
Duct Piece
Quantity
Used
Total
Equivalent
Length
1 Ft = 0.3 m
1” = 2.5 cm
Equivalent
Length*
1 ft.
(per foot
length
1 ft.
(per foot
length
8 ft.
6 ft.
15 ft.
9 ft.
20 ft.
1 ft.
5 ft.
5 ft.
15 ft.
30 ft.
30 ft.
30 ft.
24 ft.
Dimensions
Round,
straight
3¼” x 12”
straight
90° elbow
45° elbow
3¼” x 12” or
90° elbow
3¼” x 12” or
45° elbow
3¼” x 12” or
90° flat elbow
7” round to
3¼” x 12”
transition
3¼” x 12” to 7” round
transition
7” round to
3¼” x 12”
transition 90° elbow
3¼” x 12” to7” round
transition 90° elbow
Round
wall cap
with damper
3¼” x 12”
wall cap with
damper
7” round
roof cap
Round
roof vent
Total Duct Run