GE Appliances GFWN1100 Operating instructions

GEAppliances.com
Safety instructions .............. 2,s
Operating instructions
Control Panels ...................... 4-7
Features ............................ 8-9
Loading and Using the Washer .... 10, 11
Cleaning the Washer .............. 12-14
Installation instructions ...... 15-20
Preparing to Install Your Washer ...... Z5
Rough-In Dimensions ................. 16
Location of Your Washer ............. 16
Unpacking Your Washer .............. 17
Drain Requirements .................. 18
Electrical Requirements .............. 18
Water Supply Requirements .......... 18
Installing the Washer .............. 19, 20
Replacement Parts ................... 20
Troubleshooting Tips ......... 21-24
Consumer Support
Warranty ............................ 25
Service Telephone Numbers .......... 26
GFWNl100
GFWN1200
GFWH1200
GMAN1200
GFWH1500
GFWN1300
GFW H1400
GFWH1405
GFWS1500
GFWS1505
English/Fran_ais/Espafiol
ENERGYSTAR
As an ENERGYSTAR®partner,
GEhas determined that this
product meets the ENERGYSTAR®
guidelines for energy efficiency.
Printed in China
Write the model and serial
numbers here:
Model #
Serial #
Youcan find them on a label on the
side of the washer. 49-90454-1 04-12 GE

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
of fire or explosion, electric shock, or to prevent property damage, personal injury or
loss of life.
The instructions in this manual and all other literature included with this washer are
not meant to cover every possible condition and situation that mabt occur. Good, safe
practices and caution MUSTbe applied when installing, operating and maintaining
anbt appliance.
WATER HEATERSAFETY
Undercertain conditions,hgdrogen gasmag be producedin a water heater that has not been usedfor two weeks
or more. Hgdrogengas can be explosiveunder these circumstances.
Ifthe hotwater hasnot beenusedfor two weeks or more,prevent the possibilityof damage or injuryby
turning on all hot water faucets and allowing them to runfor severalminutes. Dothis before usingany electrical
appliance which isconnected to the hot water system.Thissimple procedurewill allow any built-up hydrogen
gas to escape.Sincethe gas isflammable, do not smokeor usean open flame or applianceduring this process.
PROPERINSTALLATION
Thiswasher must beproperly installedand located in accordancewith the InstallationInstructions beforeit is used.
[] Installor storewhere itwill not be exposed [] Properlyground washerto conform with allgoverning
to temperatures belowfreezingor exposed codesand ordinances.Followdetailsin Installation
to the weather,which couldcause permanent Instructions.
damage and invalidatethe warranty.
YOURLAUNDRYAREA
[] Keepthe area underneath and around your
appliances free of combustible materials such as
lint, paper, ragsand chemicals.
[] Do not leavethe washer door open.An opendoor
could entice children to hang on the door or crawl
insidethe washer.
[] Closesupervisionis necessary if this appliance is
used by or near children. Donot allow children to
play on,with or insidethis or any other appliance.
2

GEAppliances.com
WHEN USINGTHEWASHER
[]
Use this []
appliance
only for its
intended
purpose as
described in []
this Owner's
Manual.
[]
Never reach into washer while it is moving.
Wait until the machine has completely stopped
before opening the door.
Donot mix chlorine bleach with ammonia
or acids such as vinegar and/or rust remover.
Mixing different chemicals can produce a toxic
gas which may cause death.
Donot wash or dry articles that have been
cleaned in, washed in, soaked in or spotted
with combustible or explosive substances (such
as wax, oil, paint, gasoline, degreasers, dry-
cleaning solvents, kerosene, etc.)which may ignite
or explode. Do not add these substances to the
wash water. Do not use or place these substances
around your washer or dryer during operation.
The laundry process can reduce the flame
retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer's
wash and care instructions.
[]
[]
[]
Never attempt to operate this appliance
if it isdamaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
Do not slam the washer door closed. Do not try
to force the door open when locked (LOCKED
indicator ON This could result in damage to
the washer.
The washer isequipped with an electrical
overload protector. The motor will stop
if it becomes overheated. The washer will
automatically restart after a cool-down
period of up to 2 hours, if the washer
has not been manually turned off
during this time.
[] To minimize the possibility of electric shock,
unplug this appliance from the power supply
or disconnect the washer at the building's
distribution panel by removing the fuse or
switching off the circuit breaker before attempting
any maintenance or cleaning. NOTE:Pressing the
power pad does NOT disconnect the appliance
from the power supply.
WHEN NOT IN USE
[] Turn off water faucets to relieve pressure on
hoses and valves and to minimize leakage if
a break or rupture should occur. Check the
condition of the fill hoses; GErecommends
changing the hoses every 5 years.
[] Before discarding a washer, or removing it
from service, remove the washer door to prevent
children from hiding inside.
[] Do not attempt to repair or replace any part of
this appliance unless specifically recommended
in this Owner's Manual, or in published user-repair
instructions that you understand and have the
skillsto carry out.
[] Do not tamper with controls.
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVE THESE INSTRUCTIONS

About the washer control panel.
Find the illustration that closely matches Four mode! and see the descriptions for details.
Colors Whites
Normols
Stain Wash
Sanitize
Bulky
Bedding
_ewash
Spin Low Medium High High
Delicates Top Extra
Cold Cold Warm Hot Hot
Hand Wash _ My Cycle
Speed Wash c....... ]Hold3SecondsToStore
Drain+Spin m
Basket Clean PreWash Extra Rinse Signal._))
Delay Wash
Start
Add a Garment
HaM 3 secon_s TO
Lock/Unlock Controls
£stJmated Tree Remain ng
Soil Light Light Heavy
No
Spin Low Medium High(_1_1_1 _)
Tap Extra
Cold Cold Worm Hot Hot
(_1_1_1_1_)
Extra Rinse Signal-_))
Start
Add a Garment
HaM 3 Seco ds To
Lock/Unlock Controls
4
Whites
Stain Wash _
De_iCwatoeS"L(\_"
speedWosh'\\
Drain+Spin_
Basket Clean
£st_mmed T+me Remo_ ing
/
Extra Rinse Signal .)))
Start
Add nGarment
Uo_d 3seconds TO
L_k/Unl_ck Controls

GEAppliances.com
Powe r
Press to "wake up" the display. Ifthe display is active, press to put the washer into standby mode.
NOTE: Pressing Power does not disconnect the appliance from the power supply.
Wash Cycles
The wash cycles are optimized for specific types of wash loads. The chart below will help you match
the wash setting with the loads. The GentleCleaff" lifters lightly tumble the clothes into the water and
detergent solution to clean the load.
Whites For heavily to lightly soiled white cottons, household linens, work and play clothes.
Colors/Normals For heavy to lightly soiled colorfast cottons, household linens, work and play
clothes.
Stain Wash
Sanitize
(on some models)
For heavy soiled colorfast cottons, household linens, work and play clothes.
When selecting sanitize, the washer increases the water temperature to sanitize
and remove 99.9% of bacteria found in home laundry. For best results, select the
heavy soil setting when using the sanitize cycle.
Commercial, Family-Sized Clothes Washers
_S_ NSF Protocol P172
Sanitization Performance of Residential and
Bulkg Bedding For large coats, bed spreads, mattress covers, sleeping bags and similar large and
(on some models) bulky items. Large items such as blankets, comforters, jackets and small rugs.
Delicates For lingerie and special-care fabrics with light to normal soil. Provides gentle
HandWash tumbling and soak during wash and rinse.
Speed Wash For lightly soiled items that are needed in a hurry. Cycletime is approximately
30 minutes, depending on selected options.
Drain & Spin Drain and spin at any time.
Basket Clean Usefor cleaningthe basketof residueand odor. Recommended useof once per month.
NOTE:Never load laundry while using Basket Clean. The laundry may become
damaged or contaminated. See the Care and Cleaning section.
Soil Level
Changing the Soil level increases or decreases the wash time to remove different amounts of soil.
To change the Soil level, press the Soil level pad until you have reached the desired setting.
Spin Speed
Changing the Spin speed changes the final spin speed of the cycles. Always follow the fabric
manufacturer's care label when changing the spin speed.
To change the spin speed, press the Spin speed pad until you have reached the desired setting. Higher
spin speeds are not available on certain cycles, such as Delicates.
Higher spin speeds remove more water from the clothes and will help reduce dry time, but may also
increase the possibility of setting wrinkles on some fabrics.
Wash Temp
Adjust to select the proper water temperature for the wash cycle. The prewash and rinse water is
always cold to help reduce energy usage and reduce setting of stains and wrinkles.
Follow the fabric manufacturer's care label when selecting the wash temperature.
To change the wash temperature, press the Wash Temp pad until you have reached the desired
setting.
NOTE:The first 10 seconds of the wash fill is always cold. This feature assists in conditioning the fabric
and preventing stains from setting on garments.
Start/Add aGarment
Press to start a wash cycle. Ifthe washer is running, pressing it once will pause the washer and unlock
the door. Press again to restart the wash cycle.
NOTE: Ifthe washer is paused and the cycle is not restarted within 2 hours, the current wash cycle will
be cancelled.
NOTE: The washer performs automatic system checks after pressing the Start pad. Water will flow 5
in 45 seconds or less. You may hear the door lock and unlock before water flows; this is normal.

About the washer control panel.
Signal. )) Cgcle Signal
Usethe Signal pad to change
the volume ofthe end ofcycle signal. Pressthe pad until you reach
the desired volume.
PreWashil Prewash (onsome models)
Prewashisan extra wash before
the main wash. Useit for heavily soiled
clothes or for clothes with a care label
that recommends prewashing before
washing. Besureto add high-efficiency
detergent, or the proper wash additive
to the prewash dispenser.
NOTE:When selecting prewash,
it is recommended to use powder
detergent in the main wash (detergent)
compartment.
Extra Rinse Extra Rinse
Usean extra rinse when additional rinsing
is desiredto remove excessdirt and
detergent from soiledloads.
Delay Wash Delag Wash (on some models)
Youcan delaythe start of a wash cycle
for !0-18 hours,depending on the model.
Pressthe Delay Wash pad to choose the
number of hoursyou want to delay
the start of the cycle,then pressthe Start
pad.Themachine will count down and
start automatically at the correcttime.
NOTE:If you forget to fully closethe door,
a remindersignalwill beepremindingyou
todo so.
NOTE:If you open the door when thedelay
iscounting down, the machine will enter
thepausestate.Youmust closethedoor
and pressStart again in order to restart
thecountdown.
[(Lock6C_)]l
Hold 3 Seconds To
Lock/Unlock Controls
Lock
You can lock the controls to prevent any
selections from being made. Or you can
lock the controls after you have started
a cycle.
Children cannot accidentally start
the washer by touching pads with
this option selected.
To lockthe washer controls, pressand
hold the Lock pad for 3 seconds.
To unlock the washer controls, press
and hold the Lock pad for 3 seconds.
Thecontrol lock icon on the display will
light up when it ison.
NOTE:ThePower pad can still be used
when the machine is locked.
My Cycle
Hold 3 Seconds To Store
Mg Cycle (on some models)
Tosavea favoritecycle,setthe desired
settingsforwash cycle,soillevel,spinspeed
andwash temp settingsand holddown
the My Cyclepadfor 3 seconds.A beepwill
soundto indicatethe cyclehasbeensaved.
To useyour custom cycle, pressthe
My Cyclepad beforewashing a load.
Tochange the saved cycle, setthe desired
settings and hold down the My Cyclepad
for 3 seconds.
NOTE:When using My Cycle,wash
options cannot be modified after the
cycle has been started.
NOTE:If you change wash options with
My Cyclebefore starting the cycle, the
My Cyclelight will turn off and you will
be returned to the base cycle.
6

GEAppliances.com
m
awash aWash (Energy Saving Wash)
Use aWASH to save energy on specified
wash cycles, aWASH cannot be used
with Steam Refresh, Stain Wash or
Basket Clean.
Steam
Available On
Select Cycles
Steam (onsome models)
Steam adds steam into the washer
during Whites, Colors/Normals, Stain
Wash, Sanitize or Bulky Bedding
cycles.
To use:
1. Turn Power on and select a wash
cycle.
o
3.
The Steam option is only available
on Whites, Calars/Normals, Stain
Wash, Sanitize or Bulky Bedding
cycles.
Press Steam pad to activate.
Press the Start pad.
Display
Thedisplayshows the approximate time
remaininguntilthe end ofthe cycle. NOTE:The cycle time isaffected by how long
it takes the washer to fill.This depends on the
water pressure in your home.

About the washer features.
NOTE:Featuresmay not beavailableonall washermodels.
The Dispenser Drawer
Slowlyopenthe dispenserdrawer bypulling
itout untilit stops.
After adding laundryproducts,slowlyclose
the dispenserdrawer.Closingthe drawertoo
quicklycould resultin earlydispensingofthe
bleach,fabric softeneror detergent.
Youmay seewater inthe bleachand fabric
softenercompartmentsat the end ofthe cycle.
Thisisa resultof the flushing/siphoningaction
and ispart ofthe normaloperationof the
washer.
The Prewash Compartment (onsomemodels)
[] Onlyusethe PrewashCompartmentifyou
areselectingthe Prewashcyclefor heavily
soiledclothes.Add measureddetergent or
prewashadditiveto the back left prewash
compartmentof thedispenserdrawer.
[] Detergentor prewashadditive isflushed
from the dispenserinthe prewashcycle
(ifselected).
NOTE:Liquiddetergentwill drain into the
washerdrum asit isadded.
[] Detergentusagemay needto beadjustedfor
water temperature,water hardness,sizeand
soillevelof the load.Avoidusingtoo much
detergent inyour washer asit canleadto
oversudsingand detergent residuebeingleft
on the clothes.
Onsomemodels:
Removeforpowderdetergent
Detergent _ _
Setting
2XHELiquid
DetergentSetting 1
(mostcommon/
setting)J
3XHE/
Liquid _
Detergent
Setting
Appearancemay vary
Onsomemodels.
Removeforpowderdetergent
Detergent _l_f "l_
Setting __,_1_" I
2XHELiquid'/liLT
DetergentSetting/1_1"[/
mm
HE/__ _T
3X
Liquid
Detergent
Setting
Appearancemayvary
The Detergent Compartment
[] High-efficiency detergent isrequired for this
washer.Usethe detergent manufacturer's
recommendedamount.
Thedetergentselectioninsert mustbe placedin
the detergent compartment ina specific position
accordingto what type of detergentyou are
using.
[] Powder Detergent - Removethe detergent
selectioninsert.
[] Liquid Detergent - Youwill needto adjust
the insert accordingto the type of Liquid
Detergentyou are using.Theiconson the side
ofthe detergent compartmentmust lineup on
the center whenthe insert isin position.
NOTE:Not all modelshave the2x and 3x
detergentsettings.Somehaveonlg regular
HEdetergentsettings.Youmust reducethe
amount ofdetergent for 2x or 3x detergent
per bottle instructions.
Movethe insert by pullingit up and replace
it byslidingit down betweeneitherthe rear
or front detergentcompartment moldedrails,as
desired,for liquiddetergent.Removefor powder
detergent.
[] Add measureddetergentto the front left
detergentcompartment ofthe dispenser
drawer.
[]
[]
Detergentisflushedfrom thedispenser
at the beginningofthe wash cycle.Either
powderedor liquiddetergent can beused.
Detergentusagemay needto be adjustedfor
water temperature,water hardness,
sizeand soillevelofthe load.Avoidusingtoo
much detergent inyourwasher asit can lead
to oversudsingand detergent residuebeing
left on the clothes.
[] Usingmoredetergentthan the recommended
quantity cancauseresiduebuildup onyour
washer.
8

Onsomemodels.
Onsomemodels.
GEAppliances.cam
The Liquid Bleach Compartment
IMPORTANT:Thebleachcompartment
position varies by model.Besure to identify
the correct compartment for bleach before
using.
tf desired,measureout the recommended
amount of liquidbleach,notto exceed
1/3cup (80ml),and pour intothe right
compartment labeled"LIQUIDBLEACH".
Donotexceedthemaximumfill line.Overfilling
cancauseearltjdispensingofthebleachwhich
couldresultin damagedclothes.
NOTE:Donotusepowderedbleachin the
dispenser.
Onsomemode/s:
Onsomemode/s:
The Fabric Softener Compartment
IMPORTANT:Thefabric softener compartment
position varies by model. Besureto identify
thecorrect compartment for fabric softener
beforeusing.
tf desired,pour the recommendedamount
of liquidfabric softenerinto thecompartment
labeled"FABRICSOFTENER."
Useonl_lliquidfabricsoftenerin the dispenser.
Dilutewith water tothe maximumfill line.
Donotexceedthemaximumfill line.Overfilling
cancauseearly dispensingofthe fabricsoftener
which couldstain clothes.
NOTE:Donotpour fabricsoftenerdirect/_l
on thewash load.

Loading and using the washer.
Alwabts follow fabric manufacturer's care label when laundering.
Sorting Wash Loads
Sort laundry into loads that can be washed together.
Colors Soil Fabric Lint
Whites Heavy Delicates Lint Producers
Lights Normal Easy Care Lint Collectors
Darks Light Sturdy Cottons
[] Combine large and small items in a load. Load large items first. Large items should not be more than half
the total wash load.
[] Washing single items is not recommended. This mag cause an out-of-balance load. Add one or two
similar items.
[] Pillows and comforters should not be mixed with other items. This mag cause an out-of-balance load.
Preparing Clothes
[] Toavoid snags during washing:
Follow these steps to maximize garment care.
Closegarmentzippers,snaps,buttonsand hooks.
Mendseams,hems,tears.
Emptyall itemsfrompockets.
Removenonwashablegarment accessoriessuchasornamentsand nonwashabletrim materials.
[] Toavoid tangling, tie strings, draw ties and belt-like materials.
[] Brush away surface dirt and lint; treat spots and stains.
[] Promptly wash wet or stained garments to maximize results.
[] Mix garments using recommended maximum load sizes on page !!.
[] Use nylon mesh garment bags to wash small items.
[] Wash multiple garments at one time for best results.
10

GEAppliances.cam
Loading the Washer
Wash drum may be fully loaded with loosely added
items. Do nat wash fabrics containing flammable
materials (waxes, cleaning fluids, etc.J.
To add items after washer has started, press Start
and wait until the door is unlatched. The washer
may take up to 30 seconds to unlock the door
after pressing Start depending on the machine
conditions. Do not try to force open the door when
it is locked. After the door unlocks, open gently. Add
items, close the door and press Start to restart.
Maximum Loading Sizes*
WORKWEAR
/4Jeans
5 Workwear Shirts
5 Workwear Pants
LINENS
2 Bath Sheets
10 Bath Towels/
MIXEDLOAD
/4Pillowcases
2 Hand Towels
DELICATES**
7 Bras
7 Panties
SPEEDWASH
(2-4 GARMENTS)
2 Casual Wear
Work Shirts
12 Washcloths
7 Hand Towels/
2 Terrycloth
Bath Mats
OR
2 Flat Queen-Sized
Sheets
2 Fitted
q)ueen-Sized
Sheets
/4Pillowcases
2 Flat Sheets/
2 Fitted Sheets
2 Bath Towels/
/4Washcloths
OR
6 Shirts (Men's
or Women's)
/4Pair Pants
(Khakis
or Twills)
5 T-Shirts
7 Pairs of Boxers
/4Pairsof Shorts
OR
6 T-Shirts
/4Pairs of
Sweatpants
/4Sweatshirts
2 Hoodies
7 Pairs of Socks
3 Slips
2 Camisoles
/4Nightgowns
! Pair Casual Wear
Work Pants
OR
3 Soccer Uniforms
*Exceeding maximum recommended load sizes may affect cleaning performance and garment care.
**Using a nylon mesh bag for small items is recommended.
11

Cleaning the washer.
Care and Cleaning
Exterior'. Immediately wipe off any spills.Wipe with damp cloth. Do not hit surface with sharp objects.
Moving and Storage: Ask the service technician to remove water from drain pump and hoses.
Do not store the washer where it will be exposed to the weather. When moving the washer,
the tub should be kept stationary by using the shipping bolts removed during installation.
See Installation Instructions in this book. If these parts are not available, they can be ordered
by visiting our Website at GEAppliances.com or by calling 800.GE.CARES.InCanada, call 800.561.3344.
Long Vacations: Be sure the water supply isshut off at the faucets. Drain all water from the hoses if the
weather will be below freezing.
Cleaning the Interior
of the Washer
To clean the interior of the washer, select
the Basket Clean feature on the control
panel. The cycle will use more water,
in addition to bleach, to refresh your
washer.
NOTE:Readthe instructions below
completely before starting the Basket
Clean cycle.
1. Remove any garments or objects from
the washer and ensure the washer
basket isempty.
2. Open the washer door and pour
one cup or 250 ml of liquid bleach
or other washing machine cleaner
into the basket.
3. Close the door and select the Basket
Clean cycle. Pushthe Start pad.
4. When the Basket Clean cycle is
working, you will see CLn on the
display. The cycle will complete in
about 90 minutes. Do not interrupt
the cycle.
5. After the cycle is complete, leave
the door open slightly for better
ventilation.
If for any reason the cycle needs to
be interrupted, the door will not open
immediately. Forcing open the door at
this stage may cause water to flood.
The door will open after the water is
drained to a level where it would not
flood the floor.
Basket Clean may be interrupted
by pressing the Start pad in between
cycles. A power outage in the house might
also interrupt the cycle. When the power
supply is back, the Basket Clean cycle
resumes where it had stopped. When
interrupted, be sure to run a complete
Basket Clean cycle before using the
washer. If the Power pad ispressed during
BasketClean, the cycle will be lost.
IMPORTANT:
[] Run Basket Clean with 1 Cup (250 ml) of
bleach once a month.
[] After the completion of a Basket Clean
cycle, the interior of your washer may
have a bleach smell.
[] It is recommended to run a light color
load after the Basket Clean cycle.
12

GEAppliances.com
Cleaning the Pump Filter
Due to the noture of the front-lood wosher,
it issometimes possible for smoll orticles
to poss to the pump. The wosher hos o
filter to copture lost items so they ore not
dumped to the droin. To retrieve lost items,
cleon out the pump filter.
1. Using o coin or flot screwdriver
in the notch on the door, open
the occess door.
2. Ploce o shollow pon or dish under
the pump occess door ond towels
on the floor in front of the wosher to
protect the floor. It is normol to cotch
obout o cup of woter when the filter
is removed.
3. Pull down the pour spout.
o
5°
6.
Turn the pump filter counterclockwise
ond remove the filter. Open slowly to
allow the water to drain.
Cleon the debris from the filter.
Replace the filter ond turn clockwise.
Tighten securely.
7. Flip up the pour spout.
8. Close the occess door.
Pumpfilter
/
Cleaning the Door Gasket
Open the wosher door. Using both honds,
press down the door gosket. Remove ony
foreign objects if found tropped inside
the gasket, ivloke sure there is nothing
blocking the holes behind the gasket.
While holding down the door gasket,
inspect the interior gasket by pulling it
down with your fingers. Remove ony
foreign objects if found tropped inside
this gasket. IVlokesure there is nothing
blocking the holes behind the gasket.
When you ore finished cleoning
the door gasket, remove your
hands ond the gasket will return
to the operoting position.
13

Cleaning the washer.
TabonbackrightorleftdependingonmodelDispenser Drawer Area: Detergent and fabric softener may build up
in the dispenser drawer. Residue should be removed once or twice a month.
[] Remove the drawer by first pulling it out until it stops. Then reach back into
the left or right rear corner (depending on model) of the drawer cavity and
press down firmly on the lock tab, pulling out the drawer.
Locktabisvisibleonlyafterdrawerhas
beenpulledopen
[] Remove the inserts from the bleach and fabric softener compartments and
the detergent insert. Rinsethe inserts and the drawer with hot water to
remove traces of accumulated laundry products.
[] To clean the drawer opening, use a small brush to clean the recess. Remove
all residue from the upper and lower parts of the recess.
[] Return inserts to the proper compartments. Replace the dispenser drawer.
14

Installation
istructio Wher
If gou have any questions, call 800.GE.CARE5(800.452.2757)orvisitour Websiteat:GEAppliances.com
In Canada, call 800.561.3344 orvisitGEAppliances.ca
BEFORE YOU BEGIN
Read these instructions completely and carefully.
"IMPORTANT -Sovetheseinstructions
for Iocol inspector's use.
" IMPORTANT - Observe oil governing
codes ond ordinances.
. Note to Installer - Be sure to leove these
instructions with the Consumer.
. Note to Consumer - Keepthese instructions
for future reference.
, Skill level - Instolletion of this opplience requires
bosic mechonicel ond electricol skills.
, Completion time - 1-3 hours
, Proper instolletion is the responsibility of the instoller.
, Product foilure due to improper instollotion is not
covered under the Worronty.
FOR YOUR SAFETY:
IkWARNING
. This opplionce must be properly grounded ond
instolled os described in these Instollotion Instructions.
. Do not instoll or store the opplionce in on oreo where
it will be exposed to woter/weother. See the Locotion
of Your Wosher section.
. NOTE: This appliance must be properlg
grounded, and electrical service to the washer
must conform with local codes and ordinances
and the latest edition of the National Electrical
Code, ANSI/NFPA 70.
TOOLS REQUIRED
[] Adjustoble wrench or 1/2" socket with rotchet
[] Adjustoble wrench or 9/16" open-end wrench
[] Chonnel-lock odjustoble pliers
[] Corpenter's level
PARTS REQUIRED {Obtain Iocallg}
[] Water Hoses(2)
PARTS SUPPLIED
[] Cable Tie
©©
[] Inlet Hose Screen
Woshers (2) [] HoseGuide
STACK BRACKET KIT
A stock brocket kit is ovoiloble ot odditionol cost.
It con be ordered in the United stores by visiting
our Web site ot GEAppliances.com or coiling 800.
GE.CARES. In Conodo, coil 800.66!.!6!6 or visit your
Iocol GEApplionces deoler. Order kit # WE25X!00!8 or
GEFLSTACK.
3.5
OPTIONAL PEDESTAL ACCESSORY
A pedestol is ovoiloble ot odditionol cost. It con be
ordered in the United Stotes by visiting our Web site ot
GEAppliances.com or coiling 800.GE.CARES. In Conodo,
visit your Iocol GE Applionces deoler. This product
should be used with the pedestol # SBSD!37HXX
ond SBSD227FXX. Follow the pedestol Instollotion
Instructions.

Installation Instructions
LOCATION OF YOUR WASHER
Do Not Install the Washer:
1.In an area exposed to dripping water or outside
weather conditions. The ambient temperature should
never be below 60°F (1S.6°C)for proper washer
operation.
2. Inan area where it will come in contact with curtains
or drapes.
3.On carpet. The floor MUST be a hard surface with
a maximum slope of 1/2" per foot (1.27cm per
30 cm).To make sure the washer does not vibrate
or move, you may have to reinforce the floor.
NOTE:If floor is in poor condition, use 3/4" impregnated
plywood sheet solidly attached to the existing floor
covering.
IMPORTANT:
Minimum Installation Clearances
, When installed in alcove: Sides, Rear,
Top = 0" (0 cm)
, When installed in closet: Sides, Rear,
Top = 0" (0 cm), Front = 1" (2.54 cm)
. Closet door ventilation openings required:
2 louvers each 60 square in. (387 cm), located 3"
(7.6cm) from top and bottom of door
ROUGH-IN DIMENSIONS
FRONT
27.0"
= (88.8cm)
o
39.8"
(101.09cm)
SIDE
33.6" b-
(85.3cm)
*NOTE:With pedestal,52.6"
Stacked,84"
16

Installation instructions
UNPACKING THE WASHER
WARNING:Recycleordestroythecarton
and plastic bags after the washer is unpacked. Hake
materials inaccessibleto children. Children might use
them for play. Cartonscovered with rugs, bedspreads
or plastic sheetscan become airtight chambers causing
suffocation.
1. Cut and remove the top and bottom packaging straps.
2. While it isin the carton, carefully laythe washer on its
side.DONOTlay the washer on its front or back.
3. Turndown the bottom flaps-remove all base packaging,
including the cardboard, styrofoam base and styrofoam
tub support (insertedin center of base).
NOTE:If gou are installing a pedestal, proceed to
the installation instructions that come with the pedestal.
4. Carefullyreturn the washer to an upright position and
remove the carton.
5. Carefullymove the washer to within/4 feet (122cm)
of the final location.
6. Removethe following from the back sideof the washer:
/4bolts
/4plastic spacers (includingrubber grommets)
/4power cord retainers
j
J
NOTE:Failureto remove the shipping braces can cause
the washer to become severelyunbalanced.
Saveall bolts for future use.
NOTE:If you must transport the washer at a later date,
you must reinstall the shipping support hardware to prevent
shipping damage. Keepthe hardware inthe plastic bag
provided.
In caseyou misplaceyour shipping bolts, replacements
are availableat additional cost.Theg can beordered in the
United States by visiting our website at GEAppliances.com
or calling 800.GE.CARES.In Canada,call 800.661.1616.Order
kit #WH49×10039.
17

Installation Instructions
ELECTRICAL REQUIREMENTS
Read these instructions completelg and carefullg.
A WARNING:
TO REDUCETHE RISKOF FIRE,ELECTRICAL SHOCK AND
PERSONAL INJURY:
. DO NOT USE AN EXTENSION CORD OR AN ADAPTER
PLUG WITH THIS APPLIANCE.
Washer must be electricallg grounded in accordance
with local codes and ordinances, or in the absence
of local codes, in accordance with the NATIONAL
ELECTRICALCODE, ANSI/NFPA NO. 70.
CIRCUIT- Individual,properly polarizedand grounded
15-amp branch circuit fused with 15-amp time-delay fuse
or circuit breaker.
POWERSUPPLY- 2-wire, with ground, 120-volt,
single-phase, 60-Hz,alternating current.
OUTLETRECEPTACLE- Properly
grounded 3-prong receptacle to be
located so the power supply cord
is accessiblewhen the washer is
in an installed position.
GROUNDING REQUIREMENTS
A WARNING:
Improper connection ofthe equipment grounding conductor
can result in a risk of electricalshock.Checkwith a licensed
electrician ifyou are in doubt asto whether the appliance is
properlygrounded.
1. Thewasher MUSTbe grounded. Inthe event of
malfunction or breakdown,grounding will reduce
the riskof electricalshock by providing a path of least
resistancefor electrical current.
2. Sinceyour washer isequipped with a power supply
cord having an equipment-grounding conductor and
a grounding plug,the plug MUSTbe plugged into an
appropriate, copper-wired receptacle that is properly
installedand grounded in accordance with all local
codes and ordinances or in the absence of localcodes,
with the National ElectricalCodes,ANSI/NFPA70 (latest
edition).If in doubt,call a licensedelectrician.DO NOT
cut off or alter the grounding prong on the power
supply cord. Insituations where a two-slot receptacle is
present,it isthe owner's responsibilityto have a licensed
electrician replace itwith a properlg grounded
three-prong grounding-type receptacle.
WATER SUPPLY REQUIREMENTS
Hot and coldwater faucets MUSTbe installed within
42 inches (107 cm) ofyour washer'swater inlet.Thefaucets
MUSTbe 3/4" (1.9cm) garden hose-type so inlet hoses can
be connected. Water pressure MUSTbe between 10 and 120
pounds per square inch.Your water department can advise
you of your water pressure.The hot water temperature
should be setto deliverwater at 120° to 140°F(48°-60°C).
DRAIN REQUIREMENTS
!. Drain capable of eliminating 17 gals(64.3L)
per minute.
2. Astandpipe diameter of 1-1/4" (3.18cm) minimum.
3. Thestandpipe height above the floor should be:
Minimum height: 24" (61 cm)
Maximum height: 96" (244 cm)
BACK
p oii
O
T
96 in.
(244 cm)
Max.
NOTE:The drain hoseattached to the washer can reach
a 58"(147cm) high standpipe. Fora higher standpipe,
contact an authorized parts distributor.
18

Installation instructions
INSTALLING THE WASHER
1. Runsome water from the hot and cold faucets to flush
the water linesand remove particles that might clog up
the inlethoses and water valve screens.
2. Obtain inlet hoseslocally.
3. Ensurethere isa rubber
washer in the hoses.Reinstall
the rubber washer into the
hosefitting if it hasfallen out
during shipment. Carefully
connect an inlet hose to
the outside "H"outlet ofthe
water valve.Tighten by hand,
then tighten another 2/3 turn ,_(b_
with pliers.Carefully connect
the other inlet hoseto the inside"C"outlet of the water
valve.Tighten by hand;then tighten another 2/3 turn
with pliers.Donot crossthreed or over-tighten these
connections.
@
4. Installthe screen washers by inserting them into the free
ends ofthe inlet hoseswith protruded sidefacing the
faucet.
\ 'r%eTy
washers
5. Connectthe inlet hoseends to the HOTand COLDwater
faucets tightly by hand,then tighten another 2/3 turn
with pliers.Turnthe water on and checkfor leaks.
.
.
Carefully move the washer to its final location. Gently
rock the washer into position ensuring inlet hoses do
not become kinked.It is important not to damage the
rubber levelinglegswhen moving your washer to itsfinal
location. Damaged legscan increase washer vibration. It
may be helpful to spray window cleaner on the floor to
help move your washer into its final position.NOTE:To
reducevibration, ensure that all four rubber levelinglegs
are firmly touching the floor. Pushand pull on the back
right and then back left of your washer.
NOTE:Do not usethe dispenserdrawer or door to lift
the washer.
NOTE:If you are installing into a drain pan,you can use
a 24-inch long 2x4 to leverthe washer into place.
With the washer in its
final position, place
a level on top of the
washer (ifthe washer
isinstalled under a
counter, the washer
should not be able to
rock).Adjust the front
leveling legs up or down
/
to ensure the washer is resting solid. Turn the lock
nuts on each leg up towards the base of the washer
and snug with a wrench.
NOTE:Keepthe leg extension at a minimum to prevent
excessivevibration. Thefarther out the legsare extended,
the more the washer will vibrate.
Ifthe floor isnot levelor isdamaged, you may have
to extend the rear levelinglegs.
19

Installation instructions
INSTALLING THE WASHER Icont.)
8. Attach the U-shaped hose guide to the end of
the drain hose. Place the hose in a laundry tub or
standpipe and secure it with the cable tie provided in
the enclosure package.
NOTE:Placingthe drain hosetoo far down the drain pipe
can cause a siphoning action. Nomore than 7 inches of
hoseshould be in the drain pipe.There must be an air
gap around the drain hose.Asnug fit can alsocause a
siphoning action.
CableTiej CableTie_
1
CableTie
.Plug the power cord into a grounded outlet.
NOTE:Check to be sure the power isoff at the circuit
breaker/fuse box before plugging the power cord into
an outlet.
lO. Turn on the power at the circuit breaker/fuse box.
ll. Readthe rest of this Owner's Manual. It contains
valuable and helpful information that will save you
time and money.
12. Before starting the washer, check to make sure:
[] Mainpower isturned on.
[] Thewasher isplugged in.
[] Thewater faucets are turned on.
[] Theunit is leveland all four leveling legsare firmly
on the floor.
[] Theshipping support hardware isremoved
and saved.
[] Thedrain hoseis properly tied up.
[] Thereare no leaks at the faucet, drain line
or washer.
13. Runthe washer through a complete cycle.
Check for water leaks and proper operation.
14. Ifyour washer does not operate, please review
the BeforeYouCoilForServicesection before
calling for service.
15. Placethese instructions in a location near the washer
for future reference.
REPLACEMENT PARTS
If replacement parts are needed for your washer,they
can be ordered in the United States by visiting our Web
site at GEAppliances.com or by calling 800.GE.CARES.In
Canada, call 800.661.!6!6.
2O