GE SPACEMAKER WSLS1100D User manual

WSLS1100D – GE Spacemaker®Stationary Washer
Dimensions (in inches)
Washer Note: Washer wall outlet must be located within 36" of service cord
entry. Wall outlet must not be located behind dryer.
Specification Revised 8/03
360438
For answers to your Monogram,®GE Profile™or
GE®appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
GE Appliances
37-1/2
23-5/8
26
SpacemakerDryer
PREWASH
NORMAL
WASH
RINSEONLY
SPINONLY
PREWASH
NORMAL
WASH
RINSEONLY
SPINONLY
COLORS
WHITES
DELICATES
QUICKWASH
LOADRINSING
HOT/COLD
WARM/COLD
COLD/COLD
TIME
REMAINING
MIN
CLOTHESCARECYCLESELECTION
WASH
OPTIONSLOAD
SIZEWASH
CYCLETEMP
WASSH/RINSE
START
PAUSE
POWER
ON/OFF

GE Appliances
WSLS1100D –GE Spacemaker®Stationary Washer
Specification Revised 8/03
360438
WALL BRACKET
REAR VIEW FRONT VIEW
2 x 4
figure 1
figure 2
1/8" MAX
This kit consists of the following:
1 Wall mounting bracket
2 Bottom Brackets
6-1/4 x 3 inch wood screws
7-1/4 x 1-1/2 inch wood screws
12 washers
Dryer Requirements
Carefully read and follow individual dryer installation
instructions for exhausting requirements.
Dryer Mounting Position
These instructions explain two mounting positions for your 24 inch dryer.
Installation Procedure:
1. Obtain two pieces of 2x4 long enough to span at least two wall studs and the width of the dryer.
2. Locate wall stud center lines. Mark wall stud center lines on two pieces of 2x4 in relationship to
position dryer is to be mounted.
3. Referring to dimensional drawing, draw a horizontal reference line (72") from the floor to locate upper 2x4 support.
4. Position, level and secure upper 2x4 with four 1/4 x 3 inch wood screws. The bottom of the 2x4 should be
positioned on reference line.
5. Referring todimensional drawing,drawahorizontal referenceline32" downfromthe bottomofthe upper2x4support.
6. Position, level and secure lower 2x4 with two 1/4 x 3 inch wood screws. The center line of the 2x4 should be
positioned on reference line.
7. Referring to figure 1, mount the metal wall bracket 1/8 inch from the bottom of the upper 2x4 support with five
1-1/2 inch wood screws.
8. Referring to figure 2, remove one screw from each lower rear corner of dryer and, using same screws, secure
lower brackets (supplied) as shown.
9. Dryer is supplied with exhaust at the top, locate and install outside exhaust duct referring to the dimensional
drawing. For other optional exhaust directions as shown in dimensional drawing (rear and sides) refer to dryer
installation instruction sheet.
10. Position the dryer on the wall mounting bracket and check that the dryer is plumbed.
11. If the dryer needs plumbing, use some of the twelve washers supplied with the kit as spacers behind lower
brackets of figure 2 and secure the dryer to the lower 2x4 support using the remaining 1-1/2 inch wood screws.
General Information:
The back of the dryer is not accessible for service or maintenance after dryer
mounting installation is complete. It is recommended that the dryer be checked
and electrical installation completed prior to mounting. For service or maintenance
requiring rear access, the dryer must be removed from the wall.
CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE INSTALLING OR
SERVICING DRYER.
The electrical outlet must be located above the dryer, or beside the dryer if adequate
dryer-to-wall clearance is available. The outlet must be within three feet on a 240
volt dryer or a 120 volt dryer from the service cord entry on the rear of the dryer.
CAUTION
The 120 volt receptacle on the back of the
240 volt dryer must not be used with this
wall mount kit.
Figure 1
Figure 2
20" Max.
Opening
120V 20Aor
208-240V 30A
3-3/4
3
3
Rear
Exhaust
5-1/8
8
74-1/8
78 74-1/8
Service
Cord
Entry at
Bank of
Appliances
R.H
EXH
5-1/8
4" Dia.
Exhaust
3-1/8
Both
Sides
33-1/4
38
79-1/4
32
2 x 4
2 x 4
624-1/2
DSKS433
DSKS333
WSLP1100
WSLS1100
Standpipe
33" Minimum
If Less Than 33"
Use Syphon
Break Kit
WH49X228
26
28
23-7/8
6
120V
15 or 20A
1-1/2
23-5/8
Standpipe
& Faucets
33" Min.
46
WMK-35 Wall Kit Installation

Specification Revised 8/03
360438
WSLS1100D –GE Spacemaker®Stationary Washer
Features and Benefits
•Electronic one-touch controls with LED read-out –Simplify cycle selection and provide
accurate cycle times.
•One-touch loading sensing –Eliminates guesswork and helps reduce water waste.
•Multiple wash cycles –Delivers optimal cleaning results.
•Three wash/rinse temperatures –Offer better wash results and longer fabric life.
•Multiple wash/spin speeds –Matches wash action to fabric type for better cleaning
and clothes care.
•Four water levels –Offers water and energy savings.
•Stainless steel basket –It resists rust and won’t chip, peel or snag clothes.
•Model WSLS1100DWW –White on white
SpacemakerDryer
PREWASH
NORMAL
WASH
RINSEONLY
SPINONLY
PREWASH
NORMAL
WASH
RINSEONLY
SPINONLY
COLORS
WHITES
DELICATES
QUICKWASH
LOADRINSING
HOT/COLD
WARM/COLD
COLD/COLD
TIME
REMAINING
MIN
CLOTHESCARECYCLESELECTION
WASH
OPTIONSLOAD
SIZEWASH
CYCLETEMP
WASSH/RINSE
START
PAUSE
POWER
ON/OFF
GE Appliances