Geeetech acrylic Prusa I3 Operation instructions

Assemble manual of Geeetech acrylic Prusa I3
All manuals and user guides at all-guides.com
all-guides.com

Prologue
Note: This manual only applies to the 5-mm acrylic Prusa I3. We have
another one that is 8-mm.
As picture is much more helpful than words in assembly manual, so I use plenty of
pictures and less word. If you have any questions, please contact me on
www.geeetech.com and find me on Skype.
Unfold the package and take all the parts out to check the condition of
the items.
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

1. Assemble Y axis (the bottom part of the chassis)
1.1 Assemble the rods of a Y axis
Part ID
Required parts
NO.5
M10 450mm threaded rod
NO.A 12
Acrylic Fender
NO.17
M8 spring washer
NO.7
M10 washer
NO.12
M10 nut
Step1. Assemble the threaded rod
Thread the nuts and washers on the two M10 threaded rods separately. The order should be:
M10 washer > M8 spring washer M10 screw > M10 screw > M10 washer > >A 12> M10 washer >
M8 spring washer > M10 screw > M10 screw > M8 spring washer > M10 washer
All manuals and user guides at all-guides.com

Step2. Assemble the Y axis smooth rod
Slide 2 bearings on each smooth rod. Before you slide the bearings please make sure they are
clean. (Ignore the black one in between)
Part ID
Required parts
NO.3
M8 410mm smooth rod
NO.32
LM8UU Linear Bearings
All manuals and user guides at all-guides.com

1.2. Attach the front and rear Acrylic support plates of the rods.
Front Rear
Part ID
Required parts
No. A7, A 8, A 9, A 10)
Acrylic plate
N0.10
M 3 nut
No. A11
Acrylic Fender
All manuals and user guides at all-guides.com
all-guides.com

All manuals and user guides at all-guides.com

1.3 Assemble the Y idler
Part ID
Required parts
NO.31
624ZZ Ball bearing
NO. P8
Printed Y idler
NO.28
M4 X25 screw
NO.11
M4 nut
A18
Y bearing limit block
P9
Retaining ring
Step1. Put the screw through the printed Y idler piece, with the 624ZZ bearings in between.
Lock the other end of a M3 nut.
Step2. Mount the assembled idler onto the front support plates.
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

1.4 Mount the Y motor.
Part ID
Required parts
NO. A13, A14
Y-axis motor block
60
Stepper motor
35
pulley
20,24
M3 screw
10
M3 nut
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com
all-guides.com

All manuals and user guides at all-guides.com

1.5 build the printing platform
Part ID
Required parts
No.A17
Acrylic plate
No.A17
Acrylic fender (No.A17)
No.P4,P5
Printed belt mount
34
Belt
45
Zip tie
24
M3 screw
13
M3 nut
Step1. Mount the belt mount on the bottom side of the plate.
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com
all-guides.com

Step2. Get the build platform plate zip-tied to the 4 linear bearings.
All manuals and user guides at all-guides.com

Step4. Attach he heated bed.
Part ID
Required parts
56
Heat bed
42
Heating wire
Attached on the bed
thermistor
41
Thermometry wire
15
Wing nut
30
Spring
24
M3 screw
The circled part need soldering.
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

2. Assemble Y - Z axis
The main frame is held upright after the acrylic fender washers on the Y axis
threaded rods. The front of the plate should be sticking out a lot further than the
back.
3.Assemble the right and left side panel
Part ID
Required parts
(No.A2)
Acrylic left panel
(No.A3)
Acrylic right panel
((No.15)
Acrylic rear block
45
Zip tie
22
M3 screw
10
M3 nut
All manuals and user guides at all-guides.com