Geemarc Wake and Shake User manual

1 2 3
USER GUIDE
!!! Please refer to our website: www.geemarc.com for an up to date user
guide, as there may be important updates and changes you need to be
aware of !!!
What’s in the box
●Wake & Shake Light ●Power supply unit ●This instructions guide ●1 Shaker
Signs and symbols
The following symbols appear in the instructions for use and on the battery door.
WARNING : Warning instruction indicating a risk of injury or damage to
health.
IMPORTANT : Safety note indicating possible damage to the device/
accessory.
NOTE : Note on important information.
1. Safety notes
WARNING
Only operate the device with the power supply unit provided and the mains voltage
specified on the power supply unit.
Do not operate the device if it is visibly damaged.
In the event of defects or operational faults, switch the device off immediately and
disconnect it from the mains socket.
Do not pull on the mains cable or on the device to disconnect the power supply unit
from the socket.
Never plug in or unplug the power supply unit when you have wet hands.
Never hold or carry the device by the mains cable.
Keep packaging material away from children (risk of suffocation).
Arrange the mains cable so that no-one will trip over it.
Never use the device in proximity to moisture.
2. Intended use
The Wake-up Light wakes you from sleep in a gentle and natural manner. The LED
light gradually becomes brighter like a rising sun, allowing your eyes to slowly become
accustomed to the light conditions and your body to gently prepare itself for waking up.
The light intensity can be set to your personal preferences. Along with the simulated
sunrise, you can set an acoustic alarm to help you wake up. Choose between the
radio, a beep or five natural sounds or you can select shaker vibration. The Wake-up
Light provides a rested and pleasant start to your day.
3. Device functions:
Clock display
Wake-up function with simulated
sunrises and alarm
Two alarms selection
Radio
Goodnight function
5 natural sounds
Shaker vibrations
LED light can be used as a lamp
Mood light function.
USB Smart Phone charger.
MP3 Input.
WARNING
The device is only intended for the purpose described in these instructions for use.
The manufacturer is not liable for damage resulting from improper or careless use.
4. Initial use
Remove the packaging material.
Check that all parts listed are present.
Check the device, mains plug and cable for damage. Place the device on a firm,
even surface.
Remove the battery compartment cover (A11) on the rear of the device and insert
the 4 x AA batteries with corrected polarity battery symbol on compartment. The
battery supplies power to the device in the event of a power failure and is not
intended to be used as a permanent power supply.
Plug the power supply connector into the power supply socket on the underside of
the device.
Insert the mains plug into a suitable socket. The time will display and you can set
the hour format.
NOTE: All settings will go back to normal time mode after 6 seconds, press the
TONE button to exit if you want to exit the settings.
5. Cleaning and maintenance
Clean the device with a dry cloth.
Do not use any abrasive cleaning products.
Protect the device from knocks, damp, dust, chemicals, drastic changes in
temperature, and nearby sources of heat (ovens, heaters).
6. Technical Data
Dimensions:120 x 170 x 120mm
Weight: approx. 508g
Voltage supply: 100-240V; 50/60Hz; 0.7A
Protection class II
For indoor use only
Radiofrequency range: 87.5-108.0 MHz FM
Illuminance: 300lux
7. GUARANTEE
From the moment your Geemarc product is purchased, Geemarc guarantees it for the
period of two years. During this time, all repairs or replacements (at our discretion) are
free of charge. Should you experience a problem then contact our help line or visit our
website at www.geemarc.com.
The guarantee does not cover accidents, negligence or breakages to any parts. The
product must not be tampered with or taken apart by anyone who is not an authorised
Geemarc representative.
The Geemarc guarantee in no way limits your legal rights.
IMPORTANT: YOUR RECEIPT IS PART OF YOUR GUARANTEE AND MUST BE
RETAINED AND PRODUCED IN THE EVENT OF AWARRANTY CLAIM.
Please note: The guarantee applies to the United Kingdom only.
8. DECLARATIONS:
CE Directives
Geemarc Telecom SA hereby declares that this product is in compliance with the
essential requirements and other relevant provisions of the RED 2014/53/UE.
The CE declaration of conformity may be consulted at www.geemarc.com
Recycling Directives
The WEEE (Waste Electrical and Electronic Equipment) has been put in place for the
products at the end of their useful life to be recycled in the best way.
When this product is finished with, please do not put it in your domestic waste bin.
Please use one of the following disposal options:
- Remove the batteries and deposit them in an appropriate WEEE skip.
Deposit the product in an appropriate WEEE skip.
- Or, hand the old product to the retailer. If you purchase a new one, they should
accept it.
Thus if you respect these instructions you ensure human health and environmental
protection.
For product support and help visit our website at www.geemarc.com
United Kingdom: 5B Swallow Court, Swallowfields, Welwyn Garden City,
Hertfordshire, AL7 1SB, UK
telephone [phone] or fax [phone]
QUGWake&ShakeLight_En_A3_V1.9

456
9. Unit description
FRONT RIGHT
A1. LED light
A2. SET/MEM button (for adjusting time and radio station storage)
A3. ALARM button (for adjusting the alarm time n alarm type)
A4. RADIO button (for activating the radio function)
A5. SNOOZE button (for activating snooze function, goodnight function or Wake up light function)
LEFT REAR
A6. TONE button (for adjusting the volume and selecting alarm tone)
A7. LIGHT button (for switching on/off the light and adjusting the back light and colour mood light
selecting)
A8. UP/Down button (For adjusting time, alarm and volume)
A9. Aux Input Jack (For connecting the MP3 input)
A10. USB port (for charging a smart phone)
A11. Battery compartment with cover
A12. Shaker Jack (for connecting the shaker)
A13. Reset-Hole (Resetting the device to factory settings)
A14. Switching power adapter (Select UK adaptor)
10. Display description
B1. Time / alarm time or radio frequency
B2. Light symbol
B3. Auto turn off (Good night)
B4. Shaker
B5. Beep Alarm sound
B6.Radio
B7. Seagull sound
B8. Wind sound
B9. Rain forest sound
B10. Frog sound
B11. Bird sound
B12. FM radio frequency
B13. Alarm 1
B14. Alarm 2
B15. Sleep
B16. Radio station memory
11. Operation
NOTE: - All settings will go back to normal time mode after 6 seconds.
You must complete each section completely without stopping
for more than 6 seconds otherwise it will return to the beginning
of the section.
11.1 Setting the time
Shortly press the SET MEM (A2) button, the hour will flash.
12:00
Press the Up ▲(A8) button to set the hour.
12
Press the DOWN ▼(A8) button to set the minute then
00
Press the SET MEM (A2) button, Choose between 12 and 24 hour
format with the UP▲/ DOWN▼(A8) buttons.
12 hr
Press the SET MEM (A2) button, Choose Snooze time 5 to 30 minutes
at 5 minutes steps (Default is 5 minutes) with the UP▲/ DOWN▼(A8)
buttons.
ZZ 05
Press the SET MEM (A2) button to exit (Time is set).
12:00
11.2 Setting and turning on/off the alarm
Short press the ALARM (A3) button once, to set Alarm 1 .
Then press and hold the ALARM (A3) button until the alarm tone
sounds. Set the alarm time by pressing UP▲to set the Hour or DOWN▼
to set the minutes (A8) button.
Then to change the alarm sound ( the alarm must be on), short press SET
MEM (A2) button until you reach your desired alarm sound. The
alarm sound will be displayed on the screen.
The bird, frog, rain forest, wind, seagull, radio or beep
It will display a sound.
and then short press ALARM
(A3) twice.
- If you want the shaker to vibrate when the alarm is activated then plug it in
at the back of the clock in (A12)-
NOTE: If you want to stop the alarm when it is ringing, short press the
ALARM (A3) button
If you do not want the alarm to ring (turn it off completely) then short press
the ALARM (A3) button and then press and hold the ALARM
(A3) until the alarm off is displayed on the screen.
OFF
If you want to activate Alarm 2 then repeat the above procedure but short press
ALARM (A3) twice.
11.3 Setting the light to wake you up
Press and hold SNOOZE (A5) button until the is shown in the
display.
Press the UP▲or DOWN▼(A8) button to set the wake up light to OFF,15
or 30 or minutes.
The wake up light will gradually brighten before the alarm goes off.
OFF
11.4 Alarm Tone
Press the TONE (A6) button when the clock is in normal time mode.
Press the UP▲or DOWN▼(A8) button to set the tone to one of the 10
possible tone levels.
F05
11.5 Alarm Volume
Press the UP▲or DOWN▼(A8) button at normal Time mode for setting the
volume of alarm.
Default volume is U08 and maximum level is U20.
U08
11.6 Connecting Shaker Vibrator
Connect shaker vibrator at rear jack (A12).
11.7 Light Function
Shortly press the LIGHT (A7) button in normal Time mode.
The lamp will light up.
Press the UP▲or DOWN▼(A8) button adjusting the light brightness.
The default intensity L07 shown and the max brightness is L15.
L07
Press the LIGHT (A7) button again.
To switch OFF the light.
11.8 Radio Function
Press the RADIO (A4) button in normal Time mode.
The radio frequency currentlyset will appear on the display.
Press the UP▲or DOWN▼(A8) button toset the desired radio
frequency.
Tip: to start the automatic scan, press and hold the UP▲or
DOWN▼(A8) button until the scan start and then release it
again.
Press the TONE (A6) button to set the default Volume:
U06 will show on the display.
Press the UP▲or DOWN▼(A8) button to adjust the volume.
The max volume is U12.
U06
11.9 Preset Radio Station / Listening Preset Radio Station
While listening, press and hold the SET MEM (A2) button until S01 shows.
The current radio station is stored in S01.
Select a new radio station and then press and hold the SET MEM (A2)
button until S02 shows.
The new desired radio station is stored in S02.
Amaximum of 10 radio stations can be stored. Repeat process to store other
preset stations.
S01
S02
To use a register memory, in mode radio, press the button SET MEM (A2),
S01 is shown or press again to show S02 and TONE (A6) button to valid
S01
S02
11.10 Goodnight function
Have either the light or the radio on and then press and hold the
SNOOZE (A5) button and SLEEP OFFF will be shown on the display.
Press the UP▲or DOWN▼(A8) button to select desired “switch off”time
from 5 minutes to 90 minutes.
You will see the SLEEP icon flashing on the display
SLEEP
OFF
SLEEP
If you want to see how much time remains before the light/radio goes off then
short Press and hold the SNOOZE (A5) button.
11.11 Display Illumination
Press and hold the LIGHT (A7) button until U03 shown at normal time
mode.
Adjusting the display brightness by press the Light button each times.
The brightness changes U03>U04>U01>U02, Max brightness is U04.
U03
11.12 MP3 Playback Function
Press the RADIO (A4) button.
Connect the MP3 to the rear jack (A9) by cable.
AU shown on display.
AU
Press the TONE (A6) button. The default Volume U06 will show on the
display.
Press the UP▲or DOWN▼(A8) button for adjusting the volume, and the
max volume is U12.
U06
NOTE: when the audio cable is connected to rear jack (A9), the radio mode is not
available.
11.13 Smart Phone Charger Function
Connect your Smart Phone with USB cable to rear USB socket (A10) to
charge