Geemarc AMPLICALL10 User manual

This product may be purchased from Connevans Limited
secure online store at www.DeafEquipment.co.uk
DeafEquipment.co.uk
Offering you choice
Helping you choose
Connevans.info
Solutions to improve the quality of life

95dB
AMPLICALL10
Page 1
Page 13
Página 25
Telephone ring amplifier
Amplificateur de sonnerie téléphonique
Amplificador del timbre del teléfono

1
Description
DESCRIPTION
FRONT
Strobe flasher
Volume control
Tone control
Speaker
Alarm mode
switch
Low battery indicator
(Red LED)
Table mounting
Modular
j
ack PTT line
Wall mounting
screw holes
Bed Shake
r
j
ack
Adaptor jack
(option)
Modular jack PTT line o
r
for a second Amplicall10
connection
battery
compartment
(4 X AA)
REAR

2
Installation (See drawing)
1) Insert 4 AA batteries into the battery compartment, for
battery backup feature. Test batteries every year.
2) Connect the Phone cable to the line jack found at the
rear of the Amplicall 10. Connect the other end of the
cable to the on the wall.
3) Connect the telephone line cord from your telephone
into the jack found at the rear of the Amplicall 10.
4) Plug the power cable into the power adapter jack
found at the rear of the Amplicall 10. Plug the adaptor
into the mains supply at the wall (optional)
INSTALLATION
AC adaptor (option)
120V
Phone
line
RJ11
phone jack
Option: Bed
Shaker

3
Alarm Operation
1 - SETTING THE ALARM MODE
Choose which alarm mode you want by moving the alarm
mode switch to one of the following positions:
0 : no alarm
:both strobe flasher and sound alarm activated
: both strobe flasher and shaker (if connected)
activated
: both sound alarm and shaker (if connected)
activated
2 - VOLUME CONTROL SLIDE SWITCH
Set the volume of the alarm sound or power on/off.
3 - TONE CONTROL SWITCH (3 POSITIONS)
Set the tone of the alarm sound.
INSTALLATION

4
Wall Mounting
1. Drill two holes horizontally, 96mm apart, and leave the
screws protruding from the wall by 5mm.
2. Hang the base on to the two screws and pull the base
down to lock it into place.
Table Mounting
If you want to mount the unit on a table, simply place it in
the base cradle, and place the base cradle on the table.
Change The Battery
The unit requires 4×AA batteries
1. Open the battery compartment door.
2. Insert 4 x AA batteries into the battery compartment.
3. Snap the battery compartment door back into place.
Note: when the red LED indicator flashes, it is time to
replace the batteries.
When replacing the batteries, disconnect all telephone
line cords from the modular wall jacks.
Second Amplicall 10
Another Amplicall 10 can be added to the system (call
1-888-864-2446). Add the second piece on one second
PTT socket.
INSTALLATION

5
Trouble shooting
Symptom Solution
No incoming call yet the
Amplicall10 rings
automatically or rings
continuously; the
shaker vibrates
automatically or
continuously; the strobe
LED flashes
automatically.
1) Check the batteries are
inserted correctly.
2) Check the power
adaptor is connected
correctly.
3) Turn off the power
switch for 10 minutes
and then turn it on.
The red low battery
LED flashes
automatically.
1) Replace the batteries.
2) Turn off the power
switch for 10 minutes
and then turn it on.
When there is an
incoming call but no
ringing can be heard.
1) Check it is connected to
the power adaptor
correctly.
2) Check the batteries are
installed correctly.
3) Check if the volume
switch is switched on.
4) Check it is connected to
the line cord correctly.
INSTALLATION

6
When there is an
incoming call but the
shaker doesn’t vibrate.
1) Check it is connected to
the shaker correctly.
2) Check the shaker
socket to see if it has
been damaged.
3) Check the alarm mode
selection switch
position is correct.
INSTALLATION

7
- This equipment complies with Part 68 of the FCC rules
and the requirements adopted by the ACTA. On the
bottom of this equipment is a label that contains, among
other information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must be
provided to the telephone company.
- All applicable certification jacks Universal Service Order
Codes (USOC) for the equipment is provided (i.e. RJ11C)
in the package with each piece of approved terminal
equipment.
- A plug and jack used to connect this equipment to the
premises wiring and telephone network must comply with
the applicable FCC Part 68 rules and requirement
adopted by the ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed
to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
- The REN is useful to determine the quantity of devices
you may connect to your telephone line and still have all
of those devices ring when your telephone number is
called. In most, but not all areas, the sum of the REN’s of
all devices connected to one line should not exceed five
(5.0). To be certain of the number of devices you may
connect to your line, as determined by the REN, you
should contact your local telephone company to
determine the maximum REN for your calling area.
- If this equipment causes harm to the telephone network,
the telephone company will notify you in advance that
temporary discontinuance of service may be required.
REGULATORY COMPLIANCE

8
But if advance notice isn’t practical, the telephone
company will notify the customer as soon as possible.
Also, you will be advised of your rights to file a complaint
with the FCC if you believe it is necessary.
- The telephone company may make changes in its
facilities, equipment, operation or procedures that could
affect the operation of the equipment. If this happens the
telephone company will provide advance notice in order
for you to make necessary modifications to maintain
uninterrupted service.
- This equipment may not be used on coin service
provided by the telephone company. Connection to party
lines is subject to state tariffs. This equipment is hearing
aid compatible.
Warning: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
NOTE : This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. Some
cordless telephones operate at frequencies that may
cause interference to nearby TV’s and VCR’s; to
minimize or prevent such interference, the base of the
cordless telephone should not be placed near or on top
of a TV or VCR; and, if interference is experienced,
moving the cordless telephone farther away from the TV
REGULATORY COMPLIANCE

9
or VCR will often reduce or eliminate the interference.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•Consult the dealer or an experienced radio TV
technician for help.
- If trouble is experienced with this equipment, for repair
or warranty information, please contact our customer
service staff at: 1-888-864-2446
If the equipment is causing harm to the telephone
network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
- Please follow instructions for repairing if any; otherwise
do not alter or repair any part of device except as
specified.
Opening the equipment or any attempt to perform
repairs will void the warranty. For service or repairs,
call 1-888-864-2446.
REGULATORY COMPLIANCE

10
- Connection to party line service is subject to state tariffs.
Contact the state public utility commission, public service
commission or corporation for information.
- If your home has specially wired alarm equipment
connected to the telephone line, ensure the installation of
this telephone equipment does not disable your alarm
equipment. If you have questions about what will disable
alarm equipment, consult your telephone company or a
qualified installer.
- This equipment is hearing aid compatible.
REGULATORY COMPLIANCE

11
Sonic Alert warrants the phone against any defect in
materials or workmanship for the period of one year from
the date of purchase.
Should you experience a problem, contact our customer
service department. Be sure to save your sales receipt as
proof of purchase date should you need warranty
service.
Within a period of one year from purchase date, Sonic
Alert will repair or replace (our discretion) your phone at
no cost, if a defect in materials or workmanship is found.
If we elect to replace your phone, we may replace it with
a new or reconditioned product of the same or similar
design.
Repair or replacement will be warranted for a period of
90 days or the original time on the original warranty,
whichever is longer.
The warranty does not cover accidents, negligence or
breakage to any parts. This includes shipping damage,
failure to follow instructions, misuse, fire, floods, use of
incompatible accessories, Acts of God or failure in your
phone service carrier’s line service. The product must not
be tampered with or taken apart by anyone who is not an
authorized Sonic Alert representative. Tampering with
the phone will void ant written or implied warranties Sonic
Alert shall not be responsible for loss of time,
inconvenience, property damage caused by your phone
or any other accidental or consequential damages.
Warranty service is available only with proof of purchase.
GARANTIE

12
Simply send the Amplicall10(postpaid) and a copy of
your sales slip as proof of purchase to:
Sonic Alert Warranty Center 1081 West Innovation Dr.
Kearney, MO 64060
IMPORTANT : YOUR RECEIPT IS PART OF YOUR
WARRANTY AND MUST BE RETAINED AND
PRODUCED IN THE EVENT OF A WARRANTY CLAIM
Sonic Alert Warranty Center
1081 West Innovation Dr.
Kearney, MO 64060
Sales: 248-577-5400 Fax: [phone]
Customer Service & Warranty: 1-888-864-2446
GARANTIE

13
Descriptif
DESCRIPTIF
Flash lumineux
Réglage du volume
Réglage de
la tonalité
Sonnerie
Configuration
d’alarme
Indicateur de
batterie faible
Socle
AVANT
Ouvertures
pour vis de
fixation murale
Prise coussinet
Vibrant
Prise adaptateur
(option)
Prise ligne PTT Prise ligne PTT ou
pour la connection
d’un second AC10
Compartiment
des piles
(4 X AA)
ARRIERE

14
Installation (voir dessin ci-dessous)
1) Insérez 4 piles non rechargeables type 4 AA dans le
compartiment à piles. Testé les batteries tous les ans.
2) Branchez le cordon de ligne de votre téléphone entre
la prise murale et l’AMPLICALL 10 en IN.
3) Branchez le cordon RJ11/RJ11 entre l’AMPLICALL10
et votre téléphone.
4) Connectez l’adaptateur secteur vendu en option.
Contacter le 1-888-864-2446 pour en commander un.
INSTALLATION
Adaptateur secteur (option)
120V
Prise
téléphonique
Prise murale
téléphonique
Option :
Coussinet
vibrant
(
ref.:
SHAKCL_BLK)

15
1 - Configuration De L’Alarme
Sélectionnez l’alarme par le commutateur 4 positions:
0 : aucune alarme sélectionnée
: flash stroboscopie et sonnerie électronique activés
: flash stroboscopique et coussinet vibrant (si
connecté) activés
: sonnerie électronique et coussinet vibrant (si
connecté) activés
2 - Potentiometre De Volume
Vous pouvez ajuster le volume de l'alarme ; ainsi que
l'allumer ou l'éteindre.
3 - Interrupteur De Tonalite (3 Positions)
Vous pouvez choisir entre 3 tonalités d'alarme
INSTALLATION

16
Montage Mural
Percez 2 trous à l'horizontale distant de 96 mm dans
votre mur. Insérez 2 chevilles avec leurs vis. Laissez
dépasser les vis de 5 mm.
Faites glisser votre base dans les têtes de vis.
Placez ensuite l'AMPLICALL10 sur les vis et tirez la base
vers le bas afin que le boîtier soit bloqué.
Table De Montage
Si vous souhaitez installer l'AMPLICALL10 sur une table,
posez le socle, puis insérez le boitier dedans.
Remplacement Des Piles
Insérez les 4 piles type AA fournies avec l’appareil pour
son fonctionnement.
1. Ouvrez le compartiment des piles.
2. Insérez les 4 piles type AA
3. Refermez le couvercle du compartiment des piles.
Note: Si le voyant du niveau des piles clignote rouge,
vous devez les remplacer.
Lors de tout changement, débranchez le cordon de ligne
de votre base.
Ajouter un second Amplicall 10
Appeler au 1-888-864-2446 pour en commander un
second, l installer sur une deuxième prise téléphonique.
INSTALLATION

17
Aide Aux Problèmes Rencontrés
Symptome Solution
L’Amplicall10, le
coussinet vibrant ou le
flash lumineux
s’enclenche
automatiquement sans
que le téléphone sonne.
1) Vérifiez que les
batteries soient bien
insérées.
2) Vérifiez que l’adapteur
secteur soit bien
connecté.
Eteignez l’Amplicall10
pendant 10 minutes et
rallumez-le.
L’indicateur de batterie
faible clignote rouge
alors que l’Amplicall10
est connecté à
l’adaptateur secteur
1) Vérifiez l’état de la
batterie.
3) Eteignez l’Amplicall10
pendant 10 minutes et
rallumez-le.
L’Amplicall10 ne sonne
pas alors qu’il est
connecté à l’adaptateur
secteur et que les 4
batteries sont insérées.
1) Vérifiez que
l’adaptateur secteur soit
bien connecté.
2) Vérifiez que les
batteries soient bien
insérées.
3) Vérifiez que le volume
soit allumé.
4) Vérifiez que le cordon
de ligne soit bien inséré
dans l’Amplicall10.
INSTALLATION

18
L’Amplicall10 est bien
connecté à l’adaptateur
secteur ou les piles sont
bien insérées. Il sonne
ou flash lorsque le
téléphone sonne mais
le coussinet vibrant ne
fonctionne pas.
1) Vérifiez que le
coussinet vibrant soit
bien connecté.
2) Vérifiez que la prise du
coussinet vibrant ne
soit pas endommagée.
3) Vérifiez que vous avez
choisi la bonne
configuration d’alarme.
INSTALLATION