Geemarc LOOPHEAR 10 User manual

Amplified hearing assistant
Amplificateur portatif
Tragbarer Höverstäker
Amplificator portatil
Deutsch S30
Français P16
English P1
Español P44

1

2
Please refer to our website:
www.geemarc.com for an up to date user
guide, as there may be important updates and
changes you need to be aware of.
CONTENTS .............................................................. 2
INTRODUCTION ...................................................... 3
Unpacking the LoopHEARTM10 ................................. 4
DESCRIPTION ......................................................... 5
General Description .................................................. 5
INSTALLATION ........................................................ 8
Setting Up ................................................................. 8
USING THE LoopHEARTM10 ................................... 9
Turning the LoopHEARTM10 On and Off ................... 9
Tone and Balance Setting ........................................10
TROUBLESHOOTING ............................................11
SAFETY INFORMATION ........................................12
GUARANTEE ..........................................................13
FCC STATEMENT ...................................................14
RECYCLING DIRECTIVES .....................................15
CONTENTS

3
Congratulations on purchasing your Geemarc
LoopHEARTM10. The LoopHEARTM10 is a
rechargeable assistive listening device. It amplifies
speech together with sounds from a variety of sources
like TV, radio and telephone.
The LoopHEARTM10 can be used as an alternative to
Hearing Aids when using headphones.
It is important that you read the instructions below in
order to use your Geemarc LoopHEARTM10 to their full
potential. Keep this user guide in a safe place for future
reference.
INTRODUCTION
Note: users of digital hearing aids must make
sure their aids have been programmed for use
with the ‘T’ setting.

4
Unpacking the LoopHEARTM10
When unpacking the LoopHEARTM10, you should find
the following in the box:
•LoopHEARTM10 Conversation Piece
•Headset with rubber ear cushions
•3.7V Li-po Rechargeable Battery
•Micro usb / usb cable for recharging
•Lanyard (option)
•A microphone with "holder" and 3m lead (option)
•A belt clip
•1 User Guide
For product support and help visit our website at
www.geemarc.com
telephone [phone]
or fax [phone]
INTRODUCTION

5
General Description
DESCRIPTION
On/Off
Volume
control wheel.
Charge and
On LED
Charging
Port
Micro USB
(5.0 V DC)
Microphone
Port
Mode Switch
(MIC or T)
LH10
Conversation
Piece
Headset port
Internal
Microphone

6
DESCRIPTION
Battery
Compartment
Cover
Belt Clip

7
DESCRIPTION
Space for
Battery-pack
or batteries
Tone &
Balance
Setting
Plug for the
battery
pack

8
Setting Up
Open the battery compartment. Connect the supplied
rechargeable battery (3.7V) into the battery
compartment located on the rear of the LH10
Conversation Piece.
Or insert 2 single batteries (1.5V AAA non
rechargeable) instead of the set battery supplied.
With AAA battery mode, if the 'On' LED turns red
when in use, the LH10 needs to have new batteries
( No Red LED indication when using the rechargeable
battery).
To charge the battery, connect the supplied USB cable
to the micro USB socket on the left hand side of the
unit and then into the USB to PC or standard power
supply 5V DC. The power supply LED turns red..
Headset
Insert the headset lead into the headset port found on
the base of the Communication Piece.
INSTALLATION

9
Turning the LoopHEARTM10 On and Off
Switch the headset on. Ensure the mode switch is set
to (MIC). Roll the On/Off Volume control wheel
upwards. The On LED will display Green. Adjust the
Volume to a comfortable level by rolling the On/Off
Volume control wheel.
To turn the LH10 off or on, roll the On/Off Volume
control wheel downwards. The Green LED will switch
off and OFF will be showing on the On/Off Volume
control wheel
The LH10 can be used in rooms especially equipped
with a magnetic loop (conference …etc) due to its "built
in T coil". Simply by setting the mode switch to T, the
LH10 will receive the emitted magnetic waves then
amplify them to your headset. You will receive all the
benefits of the "built in T coil".
USING THE LH10