GEIGER Ward Bennett User manual

Parts List
Tools Required
o 4' level
o 3/16" Hex Wrench
o Cordless Drill
o Drill bits:
o#2 Robertson
o#3 Phillips
Page 1
Assembled H-Frame Credenza
(Configuration and number of sections varies)
1/4-20 Lock Nut
1B6CBT
Used with Bolt 1B6C9R
(qty varies)
1/4-20 X 2-1/2" Socket head
Cap Screw
1B6C9R
Attaches Horizontal Support
to Center Gable
(qty varies)
1/4-20 x 1-1/4" Socket Head
Cap Screw
1B8B88
Attaches Storage to End Gable
JHGE-1427
(qty varies)
1/4-20 x 1" Socket Head
Cap Screw
1B6C9P
Attaches Horizontal Support
to End Gable
(qty varies)
#8 x 1" Flat Head Wood Screw
50162
Attaches wood shelf or wood
Storage to Horizontal Support
95712
(qty varies)
End Gable (3/8" deep holes)
JHGE-1427
(2 per credenza)
Center Gable (Through Holes)
JHGC-1427
(qty varies)
Horizontal Support
95712
(x 2 per shelf section,
x 1 per storage section)
Wood Shelf (2x per section)
JHST-3014
(qty varies)
Stone Shelf (2x per section)
JHSTS-3014
(qty varies)
Two Door Storage
JHL2-3014
(qty varies)
Six Box Drawer Storage
JHLG-3014
(qty varies)
Three Box Drawer Storage
JHLK-3014
(qty varies)
One File Drawer Storage
JHLH-3014
(qty varies)
Two File Drawer Storage
JHLF-3014
(qty varies)
9" x 5/8" x 1/8" Metal Shim
1B8B89
Acts as washer between screws
and storage unit
(qty = 2 per storage unit)
Geiger Ward Bennett
Right ON SITE
Installation Principles
ROS-WBHF Ward Bennett H Frame Credenza
1B93V3

Page 2
1. Assemble Frames
A. Assemble frames as shown below, but do not fully tighten to allow placement of storage/shelf elements later.
Assemble with gables resting with their backs on a protected surface. Use a 3/16" Hex wrench to drive bolts into
threaded holes in gables. Make sure chamfered side of screw holes on horizontal supports are on the bottom.
Single section credenza
Multi-section credenza
End Gable (Partial holes)
JHGE-1427
Center Gable (Through Holes)
JHGC-1427
End Gable (Partial holes)
JHGE-1427
End Gable (Partial holes)
JHGE-1427
End Gable (Partial holes)
JHGE-1427
(3x) 1/4-20 x 1-1/4"
Socket Head Cap Screw
1B8B88
(3x) 1/4-20 Lock Nut
1B6CBT
(3x) 1/4-20 X 2-1/2"
Socket head Cap Screw
1B6C9R
Chamfered edges of screw holes
face downward
Geiger Ward Bennett
Right ON SITE
Installation Principles
ROS-WBHF Ward Bennett H Frame Credenza
1B93V3

Page 3
2. Assemble Shelves and Storage
A. Carefully flip assembled frame upright and place in final location.
B. Place lower shelves and storage cabinet(s) onto lower horizontal supports, make sure they are aligned in the
front and back with gables.
C. Fully tighten bolts connected in step 1.
D. Remove drawers from storage cabinets to allow access to bolt holes on interior of cabinet.
E. Bolt storage cabinet(s) and upper horizontal supports to gables as shown.
Storage unit shown without
interior drawers
and shelves
(2x) 9" x 5/8" x 1/8" Metal Shim
1B8B89
(3x) 1/4-20 X 2-1/2" Cap Screw
1B6C9R
(3x) 1/4-20 Lock Nut
1B6CBT
1/4-20 x 1-1/4" Cap Screw
1B8B88
(3x)1/4-20 x 1" Cap Screw
1B6C9P
Geiger Ward Bennett
Right ON SITE
Installation Principles
ROS-WBHF Ward Bennett H Frame Credenza
1B93V3

Page 4
3. Fasten Shelves and Storage to Horizontal Supports
A. Fasten shelves and storage unit(s) to horizontal supports using #8 x 1" (50162) wood screws.
B. Replace drawers and shelves in storage unit.
C. Level assembled H-Frame credenza.
(6x per horizontal support)
#8 x 1" Flat Head Wood Screw
50162
Note:
Stone shelves simply rest on
horizontal supports. Attach only wood shelves.
Geiger Ward Bennett
Right ON SITE
Installation Principles
ROS-WBHF Ward Bennett H Frame Credenza
1B93V3