GEM BTS-200 User manual

BTS-100 BTS-115-ANSI,115-S BTS-400ANSI,300BTS-85UK BTS-486
12~24VDC 12~24VDC 12~24VDC 12~24VDC 12~24VDC
30~60mA/12VDC
40~80mA/24VDC 30~50mA/12VDC 40~60mA/24VDC 20~40mA/12VDC 20~50mA/24VDC 60~100mA/12VDC 80~120mA/24VDC 30~60mA/12VDC 40~80mA/24VDC
Com,N/C,N/O Com,N/C,N/O Com,N/C,N/O Com,N/C,N/O Com,N/C,N/O
3A/30VDC 3A/24VDC 3A/24VDC 3A/24VDC 3A/24VDC
1~30 seconds 1~30 seconds 1~30 seconds 1~30 seconds 1~30 seconds
Green(Relay) Green(Relay) Green(Relay) 2x6 levels of LED
-20~+70ºC -20~+70ºC -20~+70ºC -20~+70ºC -20~+70ºC
N/O,N/C output setting
BTS Touch Exit Button
The BTS touch sensitive exit button has
N.O. and N.C. contact output and can be
connected directly to a electromagnetic lock
or a proximity reader in series (or in parallel).
Fig.A
Copyright © GIANNI Industries,Inc.All rights reserved.
P-MU-BTS Ver.D Published 2011.03.18
130 sec.
130 sec.
Installation Instruction
Specifications
Wiring Diagram
Mode
Operating Voltage
Current Draw
Relay contact
output
Relay rating
Relay strike time
LED status
Temperature
Other
indication indicator 2x6 levels of LED
indicator
In Fig.A, BTS controls the fail-safe locking
device directly by series connection. BTS
relay time is door-opening time. Power
Supply
Power
Supply
Control Device (Outdoor)
Relay output
control
Relay Timer
Relay Timer
BTS Touch Sensitive Switch (Indoor)
BTS Touch Sensitive Switch (Indoor)
Fig.B
Locking Device
(fail-safe)
Locking Device
(fail-secure)
Control Device (Outdoor)
Relay output
control
In Fig.B, BTS controls the fail-secure locking
device directly by parallel connection. BTS
relay time is door-opening time.
Note:
1. Make sure that the power input and relay rating output (3Amp/24VDC) are correct.
2. Make sure that the “+” and “-” wires are connected correctly.
3. The door strike or relay must have a varistor or a diode across the door strike terminals to suppress the
back EMF of the strike. Failure to do so will damage the relay contacts and electronic omponents, or
even burn the controller.

Copyright © GIANNI Industries,Inc.All rights reserved.
P-MU-BTS Ver.D Published 2011.03.18
LED
(Red)
BTS-400-ANSI,300,486
Illustration
JP setting
Warranty
BTS Touch Exit Button
Base
Slot hole
Vandal resistant screw
Stopper
Touch panel The relay will send the signals from N.C.
into N.O. contact after your finger or a
metal object touches the touch panel.
Time delay can be adjusted from 1 to 30
seconds.
Relay output
Relay output
(Touch)
(Touch)
Relay output
Relay output
(Light stay on)
(Light flash)
(Green) (Touch)
(Touch)
(Touch)
(Touch)
(Touch)
(Touch)
(Green)
(Off)
(Red)
(Off)
(Red)
(Green)
(Off)
(Green)
(Off)
(Red)
Relay contact output
(dry contact)
12~24 VDC power input
JP settingRelay Timer
(Sec.)
The product is warranted against defects in material and workmanship while used in normal service for
a period of 1 year from the date of sale to the original customer. The GEM policy is one of continual
development and improvement; therefore GEM reserves the right to change specifications without notice.