Gemini XPM-600 User manual

Page1
SERVICE MANUAL
XPM-600
XPM-900
XPM-1200
Power Amplifers
CONTENT’S:
Connections & Operations:.......................................................Page 2-5
Specifications:..............................................................................Page 6
Parts Lists:...............................................................................Page 8-20
PCBs:......................................................................................Page 21-22
Schematics:.................................................................................Page 23
Gemini Sound Products Corp.
120 Clover Place P.O. Box 6928
Edison, NJ 08818-6928
732-738-9003 (Phone) • 732-738-9006 (Fax)

1
7
23 4
6
58910 11
13
12
1
7
2 3 4
6
58
910 11
16
14 15 17 19 20
16
14 15 18

Stereo
Mono Bridge
Parallel Mono

Page4
Clip LED (15): the amplifier has true clip LEDs to help you properly
control the amplifier’s output and achieve undistorted sound. The clip
LEDs for each channel light when your signal level is so strong that
the distortion reaches 1% THD. The clip LED should not remain
constantly on or flash repeatedly during operation. For clean sound
reproduction, the clip should only light occasionally for an instant. If
the LED remains on or flashes repeatedly, you will hear distorted
sound that can be damaging to your speaker systems. If this occurs,
reduce the signal level by lowering the input level control for the
channel that is clipping or reduce the level at the source. If the clip
LED lights when no signal is present, it may indicate a RF signal on
the output which may cause damage to speakers (the RF signal will
not be audible). Please note that when you are using the amplifier in
the Mono Bridge mode, both clip LEDs of the bridged channels will
operate simultaneously.
Protect LED (16): when you first turn on the amplifier, the protect LEDs
light briefly during a turn-on delay which indicates that the outputs are
disconnected internally. There will be an audible click when the
outputs reconnect and the protect LEDs will turn off. Otherwise, the
protect LED indicates that there is a problem either in the amplifier’s
external connections, load or temperature conditions or its internal
functions. If one of these situations occur, the amplifier senses the
problem and automatically switches into protection mode. The LED
will light to warn you of the trouble and the amplifier will stop working.
If this occurs, switch off the amplifier and refer to the Trouble
Shooting Guide. If the protect LED remains lit when resuming
amplifier operation, do not use the amplifier and contact an
authorized service technician.
Level Controls (17, 18): establish the input levels required for each
channel. Only the Channel A Level Control (17) works in Mono
Bridge mode.
Operating Instructions
THE AMPLIFIER’S POWER MUST BE TURNED OFF WHEN
CHANGING MODES OF OPERATION.
Stereo Operation
The unit has two channels for stereo operation. Each channel
provides a separate and discrete signal at the speaker outputs according
to the signal received at the inputs. The following instructions are for
applications with 4 Ohm or 8 Ohm speakers of matched power ratings.
1. With the power off, set the OPERATION MODE SWITCH (3) to the
STEREO position. When the power is on, the Mono and Bridge LEDs
on the front panel will not light. If these LEDs illuminate, you have the
switch in the wrong position. Correct before continuing.
2. With the power off, connect your input cables to the channel A and B
inputs using either the XLR INPUT JACKS (1, 5) or 1/4" INPUT
JACKS (2, 4) of each channel. The other channel A and channel B
inputs can be used to link to an additional amplifier.
3. Connect the loudspeakers to the channel A and channel B SPEAKER
OUTPUTS (9, 11). THE TOTAL SPEAKER LOAD MUST BE AT
LEAST 4 OHMS PER CHANNEL. If you try to operate at a lower
impedance, the amplifier will go into protection mode and stop
operation until you correct the load conditions.
4. With the LEVEL CONTROLS (17, 18) of both channels set to zero
(fully counterclockwise), turn the POWER SWITCH (20) on. Apply a
signal to the input of the amplifier. The level of the input signal should
be as high as you will ever need it to be. This way, it will be as high
above the amplifier’s noise floor as possible, ensuring an excellent
performance and signal to noise ratio. Adjust the LEVEL CONTROLS
for each channel to achieve the desired maximum listening level.
Note, when the clip LEDs light, there is distortion present in the
amplifier’s output section. If a clip LED remains on or flashes
repeatedly, reduce the signal level by lowering the input level control
for the channel that is clipping or reduce the level at the source.
Connections, Controls and Indicators
Rear Panel
Note: 120V and 230V units have different types of output
connectors on the rear panel.
Input Section:
There are two parallel input connectors (one female XLR and one
1/4” jack) per channel. Either can be used as an input or as a link to
chain amplifiers.
XLR Input Jacks (1, 5): electronically balanced inputs accept a standard
XLR male connector. Pin 1 = shield/ground, pin 2 = hot or positive (+)
and pin 3 = cold or negative (-).
1/4" Phone Input Jacks (2, 4): accept a balanced as well as an
unbalanced line level signal. The unbalanced line uses a standard tip-
sleeve connection. The tip is positive and the sleeve is negative/
ground. The balanced line uses a tip-ring-sleeve connection. Tip =
hot or positive (+), ring = cold or negative (-), and sleeve = shield/
ground.
Operation Mode Switch (3): switch is used to set the unit for Stereo
mode, Parallel Mono mode or Mono Bridge mode.
AC Power Section:
Fuse (7): replace fuse with those of proper type and rating.
Ground Lift Switch (8) is used to lift the ground from the chassis. See
the Ground Lift Switch Instructions for more detail.
AC Cord Outlet (6) is used to attach the power cord to the unit.
Output Section:
Disconnect unit from the AC power source before making any
connections. Pay close attention to polarity (shown on the back of the
unit) when connecting your speakers. Connecting your speaker systems
using the wrong polarity will not damage your speakers, but it will impact
the quality of the sound (lack of bass and incorrect stereo image).
Speaker Outputs for 120V Unit (9, 10, 11): the speaker output jacks
are 5-way binding posts that will accept a standard banana plugs,
spade lugs or bare wire. Make sure that all the connections are clean
when using bare wire connections. If any strands of wire from one
connector touch the adjacent connector, the sound will be distorted,
and your amplifier will overheat and go into protection mode.
Speaker Outputs for 230V Unit (9, 10, 11): Neutrik Speakon
connectors are provided to connect speakers to the amplifier quickly
and easily. They are high current rated and provide very stable and
durable contacts. A third Speakon connector in the center is provided
to be used if the amplifier is in the Mono Bridge mode. Every
Speakon connector has pin 1- as negative and pin 1+ as positive.
NOTE: Total speaker impedance must not be lower than 4
Ohm per channel for Stereo and Parallel Mono modes, or 8
Ohm for Mono Bridge mode.
Front Panel
Power Switch (20): turns the unit on and off.
Power LED (19): the power LED lights when the power is on. If the
power LED does not light, refer to the trouble shooting guide.
Mono LED (12): the mono LED will light when you have set the rear
panel Operation Mode Switch (3) for parallel mono operation.
Always make sure that this switch is in the correct position and that
all speaker connections have been made correctly for the mode of
operation you wish to use before powering up the amplifier.
Bridge LED (13): the bridge LED will light when you have set the rear
panel Operation Mode Switch (3) for mono bridge operation. Always
make sure that this switch is in the correct position and that all
speaker connections have been made correctly for the mode of
operation you wish to use before powering up the amplifier.
Signal LED (14): the signal LEDs for each channel show when a signal
is present. In Mono Bridge mode, both the channel A LED and the
channel B LED will light in unison.

Page5
Parallel Mono Operation
Follow these instructions for Parallel Mono Operation using a single
input cable, and you will have the same monophonic signal on both the
channel A and the channel B outputs. Each channel’s output is
controlled independently by that channel’s level control.
1. With the power off, set the OPERATION MODE SWITCH (3) to the
PARALLEL MONO position. When the power is on, the MONO LED
(12) on the front panel will light. If the LED does not illuminate, you
have the switch in the wrong position. Correct before continuing.
2. With the power off, connect your input cables to the channel A input
only using the either the XLR INPUT JACK (5) or 1/4" INPUT JACK
(4) of channel A. The other channel A input can be used to link to an
additional amplifier.
3. Connect the loudspeakers to the channel A and channel B SPEAKER
OUTPUTS (9, 11). THE TOTAL SPEAKER LOAD MUST BE AT
LEAST 4 OHMS PER CHANNEL. If you try to operate at less than 4
Ohms per channel, the amplifier will go into the protection mode and
stop operation until you correct the load conditions.
4. With the LEVEL CONTROLS (17, 18) set to zero (fully
counterclockwise), switch the power on. Apply a signal to the input.
The level of the input signal should be as high as you will ever need it
to be. This way, it will be as high above the amplifier’s noise floor as
possible, ensuring an excellent performance and signal to noise ratio.
Adjust the LEVEL CONTROLS for each channel to achieve the
desired maximum listening level. Note, when the clip LEDs light,
there is distortion present in the amplifier’s output section. If a clip
LED remains on or flashes repeatedly, reduce the signal level by
lowering the input level control for the channel that is clipping or
reduce the level at the source.
Mono Bridge Operation
Follow these instructions to bridge the unit’s outputs. Bridging the
amplifier converts the unit to a monophonic or single channel. The
amplifier can be used with 8 Ohm or higher loads only in Mono Bridge
mode. This mode is used to provide a higher voltage with greater
headroom to your speaker. Before setting your amplifier for Mono Bridge
operation, make sure that your speaker can handle the high power level
provided by the amplifier in Mono Bridge mode. CAUTION: VOLTAGE
OVER 100 VOLTS MAY BE PRODUCED AT THE BRIDGE OUTPUT
TERMINALS IN THIS MODE.
1. With the power off, set the OPERATION MODE SWITCH (3) to the
BRIDGE position. When the power is on, the BRIDGE LED (13) on
the front panel will light. If the LED does not illuminate, you have the
switch in the wrong position. Correct before continuing.
2. With the power off, connect your input cables to channel A input only
using the either the XLR INPUT JACK (5) or 1/4" INPUT JACK (4) of
channel A. The other channel A input can be used to link to an
additional amplifier.
3. Connect the loudspeaker to the BRIDGE SPEAKER OUTPUT (10)
only. With a 230V unit, use the center speakon. With a 120V unit, use
the two innermost red terminals. Be sure the polarity of your
connections is correct. The total speaker load must be at least 8
Ohms or above. If you try to operate at less than 8 Ohms in the Mono
Bridge mode, the amplifier will go into the protection mode and stop
operation until you correct the load conditions.
4. With the CHANNEL A LEVEL CONTROL (17) set to zero (fully
counterclockwise), switch the power on. Apply a signal to the input.
The level of the input signal should be as high as you will ever need it
to be. This way, it will be as high above the amplifier’s noise floor as
possible, ensuring an excellent performance and signal to noise ratio.
Adjust the LEVEL CONTROL (17) for channel A to achieve the
desired maximum listening level. Note, when the clip LEDs light,
there is distortion present in the amplifier’s output section. If a clip
LED remains on or flashes repeatedly, reduce the signal level by
lowering the input level control for channel A or reduce the level at
the source. During Mono Bridge operation, the channel B level is
inactive, however, both channels LEDs will flash simultaneously and
show output conditions.
Using the Ground Lift Switch
Depending on your system configuration, sometimes applying the
ground will create a quieter signal path. Sometimes lifting the ground can
eliminate ground loops and hum to create a quieter signal path.
1. With the power amp on, listen to the system in idle mode (no signal
present) with the ground applied (the GROUND LIFT SWITCH (8) in
the left position).
2. Then turn the power off before moving the GROUND LIFT
SWITCH (8). Lift the ground by moving the GROUND LIFT SWITCH
to the right, turn the power back on and listen to determine which
position will provide a signal devoid of background noise and hum.
Keep the GROUND LIFT SWITCH in the ground position if the noise
level remains the same in either position.
CAUTION: DO NOT TERMINATE THE AC GROUND ON THE POWER
AMPLIFIER IN ANY WAY. TERMINATION OF THE AC GROUND CAN
BE HAZARDOUS.

Page6
UNITDOESNOTPRODUCESOUND.POWER
LEDDOESNOTLIGHT. • POWERSWITCHNOTINONPOSITION.
• POWERCABLENOTCONNECTEDTOAMPLIFIER
ORTOOUTLET.
•ACOUTLETNOTACTIVE.
• MAINAMPLIFIERFUSEDEFECTIVE.
• MOVE POWER SWITCH TO ON POSITION.
• CONNECT POWER CABLE TO AC SUPPLY.
• CHECK CONDITION OF OUTLET.
• REPLACEAMPLIFIERMAINPOWERFUSEONREAR
PANEL WITH CORRECT TYPE AND RATING.
POWER LED LIGHTS, BUT NO SOUND IS
PRODUCEDBYAMPLIFIER. • NOINPUTSOURCESIGNAL.
• INPUTSOURCENOTCONNECTED.
• INPUTCONNECTINGCABLEDEFECTIVE.
• SPEAKER(S)NOTCONNECTED.
• SPEAKERCABLEDEFECTIVE.
• SPEAKERSYSTEM(S)INOPERATIVE.
• AMPLIFIER’S LEVEL CONTROLS ARESET TO
ZERO.
• CHECK FOR PROPER FUNCTION OF INPUT
SOURCE DEVICE.
• CHECK INPUT CABLES AND CONNECTIONS.
REPLACE QUESTIONABLE CABLES WITH KNOWN
GOODCABLES.
• CHECK SPEAKER CABLES AND CONNECTIONS.
REPLACE QUESTIONABLE CABLES WITH KNOWN
GOODCABLES.
• CHECK OPERATING CONDITION AND STATUS OF
SPEAKER SYSTEM(S). BE SURE THE LEVEL
CONTROLS ARE PROPERLY SET.
SOUNDISPRESENT BUT VOLUMEISTOO
LOW EVEN THOUGH SOURCE DEVICE IS
SETTOAHIGHLEVEL.
•AMPLIFIERINPUTLEVELCONTROLSARESET
TOOLOW.
• WRONGPINCONNECTIONSINCABLES.
• ADJUSTLEVEL CONTROLS ASPERINSTRUCTIONS.
• USE CORRECT CABLES (AS SHOWN ON BACK OF
UNIT).
LOUD 50/60 HZ OR 100/120 HZ HUM IS
HEARD AT ALL TIMES THROUGH THE
SPEAKERSYSTEMS.
• IMPROPER OR DEFECTIVE GROUND
CONNECTION AT INPUTS. IMPROPER OR
DEFECTIVE GROUND AT INPUT SOURCE
DEVICE(S).
• IMPROPER OR DEFECTIVE GROUND
CONNECTIONONACOUTLET.
• GROUND LOOP THROUGH AC LINE
CONNECTION/RACKMOUNTING.
• CHECKFOR PROPERACLINEGROUND ON POWER
AMP AND ALL INPUT DEVICES.
• CHECKINPUT CABLES FORALL SOURCE DEVICES
AND SIGNAL PROCESSING AS WELL AS INPUT
CABLES TO POWER AMPLIFIER. CHECK POSITION
OF GROUND LIFT SWITCH AS PER INSTRUCTIONS
FOR LIFTING THE GROUND.
• NEVERLIFTTHEACLINEGROUNDONTHEPOWER
AMPLIFIER.IF YOUARENOTTOTALLY FAMILIARWITH
GROUND LIFTING OR UNIFICATION PROCEDURES,
DONOTATTEMPTTHEMWITHOUTFIRSTCONSULTING
YOUR DEALER OR A QUALIFIED SOUND
TECHNICIAN FOR MORE INFORMATION ON
GROUNDING. IMPROPERLY DONE, SUCH
PROCEDURES CAN POSE A SAFETY AND/OR FIRE
HAZARD.
SOUNDISDISTORTED. • DISTORTIONOCCURRINGINSOURCEDEVICE.
• INPUTLEVELISSETTOOHIGH.
• CHECK CLIP INDICATORS ON INPUT SOURCE
DEVICES AND RESET LEVELS IF NECESSARY TO
ELIMINATE DISTORTION.
• ADJUSTLEVEL CONTROLS ASPERINSTRUCTIONS.
PROTECTLEDREMAINS LITORGOESON
ANDOFFINTERMITTENTLYAFTER USING
AMPLIFIERFORASHORTTIME.
• UNIT IS OPERATING AT EXCESSIVELY HIGH
TEMPERATURE.
• EXTREMELYLOWSPEAKERIMPEDANCE.
• SHORTINSPEAKERCONNECTORS,SPEAKER
CABLEORSPEAKERSYSTEM.
• CHECK THAT AMPLIFIER IS ADEQUATELY
VENTILATED ON THE FRONT AND REAR PANELS
WHERE THE AIR VENTS AND FANS ARE LOCATED.
IF OVERHEATED, LET THE AMPLIFIER COOL DOWN
BEFORE APPLYING AN INPUT SIGNAL.
• CHECK THE POSITION OF OPERATION MODE
SWITCH. BE SURE THAT THE SPEAKER
CONNECTIONS ARE MADE IN ACCORDANCE WITH
THE SWITCH SETTING.
• VERIFYSPEAKERSYSTEMIMPEDANCES.BESURE
THE TOTAL SPEAKER SYSTEM IMPEDANCE IS AT
LEAST 4 OHMS PER CHANNEL WHEN THE
OPERATION MODE SWITCH IS IN THE STEREO
POSITION OR PARALLEL MONO POSITION. IF THE
SWITCH IS IN THE BRIDGE MODE, THE IMPEDANCE
MUST BE AT LEAST 8 OHMS. IF YOU ARE NOT SURE
OF YOUR TOTAL SPEAKER IMPEDANCE LOAD,
CONTACTYOURDEALERFOR MORE INFORMATION.
• CHECK CONDITION OF SPEAKER CABLES.
• IF USING BARE WIRE CONNECTIONS ON THE
OUTPUTS OF THE AMPLIFIER, BE SURE THAT NO
STRANDS FROM ONE CONNECTOR ARE TOUCHING
ANY OTHER CONNECTOR.
FUSEBLOWSINTERMITTENTLY. • SPEAKERLOADIMPEDANCEISTOOLOW.
• TYPE OR RATING OF THE FUSE IS NOT
CORRECT.
• CHECK FOR SHORTS ON THE OUTPUTS.
• CHECK YOUR SPEAKER IMPEDANCE (INFO FROM
DEALER).
• CHECK THAT THE FUSE TYPE AND RATING IS
CORRECT.
PROTECT LED(S) STAY ON WITH NO
SPEAKERS CONNECTED AND WITH THE
AMPLIFIERCOOLEDDOWN.
• FAILEDAMPLIFIER. • CONTACT THE GEMINI SERVICE DEPARTMENT OR
YOUR AUTHORIZED DEALER TO SPEAK TO A
QUALIFIED SERVICE TECHNICIAN. IN THE U.S.A.
CALLTOLLFREE1-800-476-8633
SYMPTOM CAUSE SOLUTION

Page7
Specifications
Output Power EIA: 1kHz @ 1% THD
XPM-600 XPM-900 XPM-1200
Single Channel 8Ω230 310 400
Both Channels Driven 8Ω200 280 360
Single Channel 4Ω300 480 630
Both Channels Driven 4Ω270 400 530
Mono Bridge 8Ω550 800 1060
Dynamic Headroom: XPM-600 XPM-900 XPM-1200
8Ω1.4 1.4 1.3
4Ω2.2 2.2 2.2
Frequency Response............................................................20 Hz - 60 kHz
Total Harmonic Distortion......less than 0.1%, typical 0.03% at 1 kHz
Intermodulation Distortion.......................less than 0.05% (SMPTE)
Signal to Noise Ratio..........................100 dB below rated power, 8Ω
Damping Factor..............................greater than 200 @ 8Ω
Slew Rate.................................................................................25 V/µS
Voltage Gain....................................................................33 dB
Input Sensitivity (for rated power at 8 Ohm):
XPM-600 XPM-900 XPM-1200
0.9 Vrms 1.1 Vrms 1.2 Vrms
Input Impedance Unbalanced....................................................10 kOhms
Input Impedance Balanced.......................................................20 kOhms
Power consumption: XPM-600 XPM-900 XPM-1200
700 VA 900 VA 1100 VA
Note: power consumption is given at rated power at 8Ωper channel, both
channels driven.
AC Power Requirement:
(power connection is factory configured)............................120V/ 60 Hz
230V/ 50 Hz
Indicators.......................................................................1 Power Indicator
1 Signal LED per channel
1 Clip LED per channel
1 Protect LED per channel
1 Mono LED
1 Bridge LED
Cooling....................................2 Speed Dual Fan; Front-to-Rear Forced Air
Protection...........Short Circuit, DC, Thermal Cut-off, Sub/ultrasonic
Frequency Filters, In-rush Current Limiter, Turn-on Delay
Connectors:
Balanced/Unbalanced Inputs....................................1/4" Jack
Balanced Inputs............................................XLR Female Jack
SpeakerOutputs(120V unit)..........................................5-way binding posts
Speaker Outputs (230V unit)...........Speakons (ch.A, ch.B and bridge)
Dimensions...................................19" x 13.75" x 3.5" (483 x 350 x 89 mm)
Weight XPM-600 XPM-900 XPM-1200
25.8 lbs 29 lbs 31.2 lbs
11.7 kg 13.2 kg 14.2 kg
* Specifications and design are subject to change without notice for
purpose of improvement.

Page8
1) 102056543301 SPACER XPM-900 PC 2
2) 102119214701 CARTON XPM-600 PC 1
3) 102260018001 EXT.CARTON XPM-600 PC 1
4) 103012005700 SPACER 1200x570m/m PC 1
5) 105011008501 HOLDER XPM-900 PC 2
6) 105032409601 WALL XPM-900 PC 1
7) 105034608501 SILD PANEL XPM-900 PC 2
8) 105242608601 BACK BOARD XPM-600 PC 1
9) 105343431801 TOP COVER XPM-900 PC 1
10) 105443431701 BOTTOM CABI XPM-900 PC 1
11) 107042002501 AIRFILTER 420x25m/m XPM-900 PC 1
12) 107042004001 PVC COVER XPM-600 PC 1
13) 1070ACS03501 ACS-3.5 PVC RED PC 5
14) 1070KG-010— M0VEABLE BUSHING KG-010 CM 2
15) 1070SCB-10— SPACER SUPPORTS SCB-10 XPM-900 PC 4
16) 1070SS-6—— SELF RETATINING SPALERS SS-6 PC 1
17) 1070YJ-98—- NYLON CLAMPER YJ-98 PC 1 2
18) AL201AL50101 AL201/AL501 SJT W-A 14AWG 6FT PC 1
19) AO016D130—- 3P AC INLET AC-016D130 XPM-900 PC 1
20) 105006400001 6.4m/m PIN PC 6
21) 106203003003 RECTIFER HEAT SINK XPB-1600 PC 1
22) 106201302001 HEAT SINK BLACK 13x20 XPM-900 PC 1
23) 1070LED-3.5- LED SPACER SUPPORT LED-3.5 PC 9
24) 700KBP060002 RECTIFIER KBP06 2A 600V PC 1
25) 700MP3504W02 RECTIFIER MP3504W 35A 400V PC 1
26) CCN0A101250K CERAMIC CAP 100P 250V PC 6
27) CCN0A680500J CERAMIC CAP 68P 500V NPO 5% PC 2
28) COIL16115T6L COIL 1.6x10.1x11.5T-6L XPM-900 PC 2
29) ECL04700080M ELEC CAP 4700u80v PC 4
30) ECS00010050M ELEC CAP 10u50v PC 4
31) ECS00100025M ELEC CAP 100u25v PC 4
32) ECS00100100M ELEC CAP 100u100v PC 4
33) ECS00220016M ELEC CAP 220u16v PC 6
34) ECS01000025M ELEC CAP 1000u25v PC 1
35) ECS02200025M ELEC CAP 2200u25v PC 1
36) ICNJM3404AD- IC NJM3404AD PC 2
37) ICTL072CP—- IC TL072CP PC 1
38) JS1001025003 BASE 3P 2.5m/m PC 2
39) JS1001025012 BASE 12P 2.5m/m PC 1
40) JS1001R25002 BASE 2P JS-1001R-02 PC 2
XPM-600

Page9
41) LDG050210030 LED 5m/m GREEN PC 5
42) LDR050410030 LDE 5m/m RED PC 2
43) LDY050610030 LDE 5m/m YELLOW PC 2
44) MJ0860250900 CONNOC JACK 086-25-90 PC 2
45) MJCPJ-065—- JACK CPJ-065 XPM-900 PC 2
46) MPMEA104250K MEA .1u 250V 10% PC 6
47) MPMEF104250K MEF .1u 250V 10% PC 2
48) NTM3x07x030Y NUT 3m/m W/S (0J0010-030001) PC 1
49) RC0200A47005 RESISTORS 4.7 ohm 2W M PC 2
50) RC0201000005 RESISTORS 10 ohm 2W M PC 2
51) RC0202230005 RESISTORS 22 K 2W M PC 2
52) RC0204720005 RESISTORS 4.7 K 2W M PC 2
53) RC0205620005 RESISTORS 5.6 K 2W M PC 2
54) RL832——12 832-1C-C-12D XPM-900 PC 2
55) SR01MS3x061B MS 3x6 BLACK PC 1
56) SR01TP4x204Y TP4x20 (1JBH6C-042021) PC 1
57) SWL————1 SS004-P2430Em-PC10 XPM-900 PC 1
58) SWS————1 SS004-P022 BY-PF8 PC 1
59) TRMJE340—0 MJE340 PC 2
60) TRMJE350—0 MJE350 PC 2
61) TRMPSA13—0 TR MPSA13 PC 2
62) TRTIP122—0 TIP122 PC 1
63) TRZ0103——0 TRIAC Z0103 MA1A600V RR-15 PC 2
64) W20105135205 1015#14 GREEN XPM-900 PC 1
65) W20105185205 1015#14 GREEN XPM-900 PC 1
66) W20105235208 1015#14 GRAY XPM-900 PC 1
67) W20105375202 1015#14 RED XPM-900 PC 1

Page10
XPM-600E
STEREO MOSFET POWER AMPUFIER
================== ================================= ======= ==============
================== ================================= ======= ==============
68) W20105375202 1015#14 RED XPM-900 PC 1
69) W2120A3000BB 1007#26 MIX XPM-900 PC 1
70) WS204x10x07W SPRING W/S.M4-L(2JS100-040050) PC 1
71) 106202602001 ALUMINUM PLATE 26x20m/m t=3 PC 4
72) 106219207601 HEAT SINK 192x76x60 XPM-900 PC 2
73) PTH9M222—E2 PTH9M04BE222TS2F333 XPM-900 PC 2
74) PTH9M471—H1 PTH9M04BH471TS2F333 XPM-900 PC 2
75) SR01MS3x061B MS 3x6 BLACK PC 4
76) SR01MS3x161W MS 3x16 (1JBHMC-031600) PC 4
77) SR01TP3x103B TP 3x10 BLACK PC 4
78) SR03TP4x084B FMT+W TP 4x8 BLACK PC 8
79) TRBUZ900NDP0 BUZ900NDP MOSFET XPM-600 PC 2
80) TRBUZ905DP-0 BUZ905DP MOSFET XPM-600 PC 2
81) WS132x08x10W 3.2x0.8x10 (2IFA032-081000) PC 4
82) WS203x08x05W SPRING W/S.M3-L(2JS100-030050) PC 1 0
83) 2SA970BL—0 TR 2SA970 BL PC 1 0
84) 2SC2240BL—0 TR 2SC2240 BL PC 4
85) 6003501950 XPM-900 MAIN PC BOARD T=2oz PC 1
86) 700033050001 ZENER 3.3v 500mw PC 6
87) 700075050001 ZENER 7.5V 500mw PC 1
88) 700120050001 ZENER 12V 500mw PC 6
89) 700150050001 ZENER 15V 500mw PC 1
90) 700150100001 ZENER 15V 1W PC 2
91) 7001N4004051 DIODE 1N4004 PC 6
92) 7001N4148051 DIODE 1N4148 PC 1 3
93) MCT0A102100J MYLAR CAP .001u T PC 2
94) MCT0A153100J MYLAR CAP .015u T PC 2
95) MCT0A182100J MYLAR CAP .0018u T PC 2
96) MCT0A473100J MYLAR CAP .047u T PC 1
97) MPMSC104100J MSC .1u 100V 5% T PC 1 5
98) RC0031010005 RESISTORS 100 ohm 1/4W T PC 4
99) RC0031020005 RESISTORS 1 K 1/4W T PC 2 1
100) RC0031030005 RESISTORS 10 K 1/4W T PC 1 6

Page11
101) RC0031040005 RESISTORS 100 K 1/4W T PC 2
102) RC0031050005 RESISTORS 1 M 1/4W T PC 1
103) RC0031520005 RESISTORS 1.5 K 1/4W T PC 2
104) RC0032020005 RESISTORS 2 K 1/4W T PC 3
105) RC0032210005 RESISTORS 220 ohm 1/4W T PC 2
106) RC0032230005 RESISTORS 22 K 1/4W T PC 2
107) RC0033030005 RESISTORS 30 K 1/4W T PC 4
108) RC0033040005 RESISTORS 300 K 1/4W T PC 2
109) RC0033320005 RESISTORS 3.3 K 1/4W T PC 4
110) RC0034700005 RESISTORS 47 ohm 1/4W T PC 4
111) RC0034730005 RESISTORS 47 K 1/4W T PC 4
112) RC0035110005 RESISTORS 510ohm 1/4W T PC 4
113) RC0036830005 RESISTORS 68 K 1/4W T PC 4
114) RC0038210005 RESISTORS 820 ohm 1/4W T PC 2
115) RC0038220005 RESISTORS 8.2 K 1/4W T PC 2
116) RC0050A10005 RESISTORS 1 ohm 1/2W T PC 1
117) RC0053030005 RESISTORS 30 K 1/2W T PC 2
118) RC0054730005 RESISTORS 47 K 1/2W T PC 2
119) RM0030K47501 RESISTORS 475 ohm 1/4W T PC 2
120) RM00310K0001 RESISTORS 10K 1% 1/4W T PC 8
121) 105006400001 6.4m/m PIN PC 2
122) 6000680600 XPM-900 POWER PC BOARD T=oz PC 1
123) MPMPX473275K MPX .047u 275VAC 10% PC 1
124) NTC0120L NTC 20A SCK-0120 XPM-900 PC 1
125) RS0500122005 1.2 K 5W SQP TYPE PC 1
126) W2010G130051 1015#14 BROWN XPM-900E PC 1
127) W2010G180056 1015#14 BLUE XPM-900E PC 1
128) FAD012080001 SP802512H L=350m/m+XH PC 2
129) FH63032I FUSE HOLD HTB-32I VDE TYPE PC 1
130) FS630ULC060F FUSE 6x30 FAST/GLASS U/C 6A PC 1
131) FTSF-006 PLASTIC FOOT SF-006 PC 4
132) IBXPM900—GI MANUAL XPM-900 (GEMINI) PC 1
133) KB1819BL0001 KNOB 18x19 BLACK XPM-900 PC 2
134) NTM8x17x080B NUT 5/16 (0A0220-310005) PC 1
135) PB420215 PLOY BAG 8.5"x16.5"X0.05 PC 1
136) PT130———2 TRANS. 130m/m XPM-600E 230V PC 1
137) SR01MS3x042B MST 3x4 BLACK(1JPH1C-030424) PC 2
138) SR01MS3x061B MS 3x6 BLACK(1JBHMC-030604) PC 1 0
139) SR01MS3x121B MS 3x12 BLACK PC 1

Page12
140) SR01MS3x081W MS 3x8 (1JPHMC-030800) PC 1
141) SR01MS4x061W MS 4x6 (PLATING) PC 1
142) SR01MS4x082B MST 4x8 BLACK (1JBH1C-040824) PC 1 6
143) SR01TP3x063B TP 3x6 BLACK (1JBHCC-030625) PC 6
144) SR01TP3x103B TP 3x10 BLACK (1JBHCC-031024) PC 4
145) SR03TP4x084B FMT+W TP 4x8 (1JBP6C-040825) PC 1 4
146) SR10MS8x751B 5/16x3" (1ATKMO-31C004) PC 1
147) SWP————9 R22-22B-11B XPM-900 PC 1
148) VR16A1031501 16K4x1 L-15 XPM-900 PC 2
149) W2010G445101 1015#14 BROWN XPM-900E PC 1
150) W2010G505106 1015#14 BLUE XPM-900E PC 1
151) W2010I12510A 1015#18 GR+YL PC 1
152) W20110120101 1015#14 BROWN XPM-900E PC 1
153) W5010A370032 2852#26 RED XPM-900 PC 1
154) W5010A460038 2852#26 GRAY XPM-900 PC 1
155) WDGEMINI GEMINI WARRANTY CARD PC 1
156) WS407x03x09Y EXT TOOTH W/S. 3m/m PC 1
465

Page13
1 ) 102056543301 SPACER XPM-900 PC 2
2 ) 102119214702 CARTON XPM-900 PC 1
3 ) 102260018002 EXT.CARTON XPM-900 PC 1
4 ) 103012005700 SPACER 1200x570m/m PC 1
5 ) 105011008501 HOLDER XPM-900 PC 2
6 ) 105032409601 WALL XPM-900 PC 1
7 ) 105034608501 SILD PANEL XPM-900 PC 2
8 ) 105242608603 BACK BOARD XPM-900 PC 1
9 ) 105343431801 TOP COVER XPM-900 PC 1
10) 105443431701 BOTTOM CABI XPM-900 PC 1
11) 107042002501 AIRFILTER 420x25m/m XPM-900 PC 1
12) 107042004002 PVC COVER XPM-900 PC 1
1 3 ) 1070ACS03501 ACS-3.5 PVC RED PC 5
1 4 ) 1070KG-010— M0VEABLE BUSHING KG-010 CM 2
1 5 ) 1070SCB-10— SPACER SUPPORTS SCB-10 XPM-900 PC 4
1 6 ) 1070SS-6—— SELF RETATINING SPALERS SS-6 PC 1
17 ) 1070YJ-98—- NYLON CLAMPER YJ-98 PC 1 2
18) AL201AL50101 AL201/AL501 SJT W-A 14AWG 6FT PC 1
1 9 ) AO016D130—- 3P AC INLET AC-016D130 XPM-900 PC 1
2 0 ) 2SA970BL—0 TR 2SA970 BL PC 1 0
2 1 ) 2SC2240BL—0 TR 2SC2240 BL PC 4
2 2 ) 6003501950— XPM-900 MAIN PC BOARD T=2oz PC 1
23) 700033050001 ZENER 3.3v 500mw PC 6
24) 700075050001 ZENER 7.5V 500mw PC 1
25) 700120050001 ZENER 12V 500mw PC 6
26) 700150050001 ZENER 15V 500mw PC 1
27) 700150100001 ZENER 15V 1W PC 2
28) 7001N4004051 DIODE 1N4004 PC 6
29) 7001N4148051 DIODE 1N4148 PC 1 3
3 0 ) MCT0A102100J MYLAR CAP .001u T PC 2
3 1 ) MCT0A153100J MYLAR CAP .015u T PC 2
3 2 ) MCT0A182100J MYLAR CAP .0018u T PC 2
3 3 ) MCT0A473100J MYLAR CAP .047u T PC 1
3 4 ) MPMSC104100J MSC .1u 100V 5% T PC 1 5
3 5 ) RC0031010005 RESISTORS 100 ohm 1/4W T PC 4
3 6 ) RC0031020005 RESISTORS 1 K 1/4W T PC 2 1
3 7 ) RC0031030005 RESISTORS 10 K 1/4W T PC 1 6
3 8 ) RC0031040005 RESISTORS 100 K 1/4W T PC 2
3 9 ) RC0031050005 RESISTORS 1 M 1/4W T PC 1
4 0 ) RC0031520005 RESISTORS 1.5 K 1/4W T PC 2
XPM-900

Page14
4 1 ) RC0032020005 RESISTORS 2 K 1/4W T PC 3
4 2 ) RC0032210005 RESISTORS 220 ohm 1/4W T PC 2
4 3 ) RC0032230005 RESISTORS 22 K 1/4W T PC 2
4 4 ) RC0033030005 RESISTORS 30 K 1/4W T PC 4
4 5 ) RC0033040005 RESISTORS 300 K 1/4W T PC 2
4 6 ) RC0033320005 RESISTORS 3.3 K 1/4W T PC 4
4 7 ) RC0034700005 RESISTORS 47 ohm 1/4W T PC 4
4 8 ) RC0034730005 RESISTORS 47 K 1/4W T PC 4
4 9 ) RC0035110005 RESISTORS 510ohm 1/4W T PC 4
5 0 ) RC0036830005 RESISTORS 68 K 1/4W T PC 4
5 1 ) RC0038210005 RESISTORS 820 ohm 1/4W T PC 2
5 2 ) RC0038220005 RESISTORS 8.2 K 1/4W T PC 2
5 3 ) RC0050A10005 RESISTORS 1 ohm 1/2W T PC 1
5 4 ) RC0053030005 RESISTORS 30 K 1/2W T PC 2
5 5 ) RC0054730005 RESISTORS 47 K 1/2W T PC 2
5 6 ) RM0030K47501 RESISTORS 475 ohm 1/4W T PC 2
5 7 ) RM00310K0001 RESISTORS 10K 1% 1/4W T PC 8
58) 105006400001 6.4m/m PIN PC 6
59) 106201302001 HEAT SINK BLACK 13x20 XPM-900 PC 1
60) 106203003003 RECTIFER HEAT SINK XPB-1600 PC 1
61) 1070LED-3.5- LED SPACER SUPPORT LED-3.5 PC 9
6 2 ) 700KBP060002 RECTIFIER KBP06 2A 600V PC 1
6 3 ) 700MP3504W02 RECTIFIER MP3504W 35A 400V PC 1
6 4 ) CCN0A101250K CERAMIC CAP 100P 250V PC 6
6 5 ) CCN0A680500J CERAMIC CAP 68P 500V NPO 5% PC 2
66) COIL16115T6L COIL 1.6x10.1x11.5T-6L XPM-900 PC 2
6 7 ) ECL06800100M ELEC CAP 6800u100v PC 4
6 8 ) ECS00010050M ELEC CAP 10u50v PC 4
6 9 ) ECS00100025M ELEC CAP 100u25v PC 4
7 0 ) ECS00100100M ELEC CAP 100u100v PC 4
7 1 ) ECS00220016M ELEC CAP 220u16v PC 6
7 2 ) ECS01000025M ELEC CAP 1000u25v PC 1
7 3 ) ECS02200025M ELEC CAP 2200u25v PC 1
7 4 ) ICNJM3404AD- IC NJM3404AD PC 2
7 5 ) ICTL072CP—- IC TL072CP PC 1
76 ) JS1001025003 BASE 3P 2.5m/m PC 2
77 ) JS1001025012 BASE 12P 2.5m/m PC 1
78) JS1001R25002 BASE 2P JS-1001R-02 PC 2
7 9 ) LDG050210030 LED 5m/m GREEN PC 5
8 0 ) LDR050410030 LDE 5m/m RED PC 2

Page15
8 1 ) LDY050610030 LDE 5m/m YELLOW PC 2
82) MJ0860250900 CONNOC JACK 086-25-90 PC 2
8 3 ) MJCPJ-065—- JACK CPJ-065 XPM-900 PC 2
8 4 ) MPMEA104250K MEA .1u 250V 10% PC 6
8 5 ) MPMEF104250K MEF .1u 250V 10% PC 2
8 6 ) NTM3x07x030Y NUT 3m/m W/S (0J0010-030001) PC 1
8 7 ) RC0200A47005 RESISTORS 4.7 ohm 2W M PC 2
8 8 ) RC0201000005 RESISTORS 10 ohm 2W M PC 2
8 9 ) RC0202230005 RESISTORS 22 K 2W M PC 2
9 0 ) RC0204720005 RESISTORS 4.7 K 2W M PC 2
9 1 ) RC0205620005 RESISTORS 5.6 K 2W M PC 2
9 2 ) RL832——12 832-1C-C-12D XPM-900 PC 2
9 3 ) SR01MS3x061B MS 3x6 BLACK PC 1
9 4 ) SR01TP4x204Y TP4x20 (1JBH6C-042021) PC 1
9 5 ) SWL————1 SS004-P2430Em-PC10 XPM-900 PC 1
9 6 ) SWS————1 SS004-P022 BY-PF8 PC 1
9 7 ) TRMJE340—0 MJE340 PC 2
9 8 ) TRMJE350—0 MJE350 PC 2
9 9 ) TRMPSA13—0 TR MPSA13 PC 2
100) TRTIP122—0 TIP122 PC 1
101) TRZ0103——0 TRIAC Z0103 MA1A600V PC 2
102) W20105135205 1015#14 GREEN XPM-900 PC 1
103) W20105185205 1015#14 GREEN XPM-900 PC 1
104) W20105235208 1015#14 GRAY XPM-900 PC 1
105) W20105375202 1015#14 RED XPM-900 PC 1
106) W2120A3000BB 1007#26 MIX XPM-900 PC 1
107) WS204x10x07W SPRING W/S.M4-L(2JS100-040050) PC 1
108) 106219207601 HEAT SINK 192x76x60 XPM-900 PC 2
109) PTH9M222—E2 PTH9M04BE222TS2F333 XPM-900 PC 2
110) PTH9M471—H1 PTH9M04BH471TS2F333 XPM-900 PC 2
111) SR01MS3x061B MS 3x6 BLACK PC 4
112) SR01MS3x121B MS 3x12 BLACK PC 1 2
113) SR01TP3x103B TP 3x10 BLACK PC 4
114) SR03TP4x084B FMT+W TP 4x8 BLACK PC 4
115) TRBUZ901P—0 BUZ901P MOSFET XPM-900 PC 6
116) TRBUZ906P—0 BUZ906P MOSFET XPM-900 PC 6
117) WS132x08x10W 3.2x0.8x10 (2IFA032-081000) PC 1 2
118) WS203x08x05W SPRING W/S.M3-L(2JS100-030050) PC 1 6
119) 105006400001 6.4m/m PIN PC 2
120) 6000680600— XPM-900 POWER PC BOARD T=oz PC 1

Page16
121) MPMPX473275K MPX .047u 275VAC 10% PC 1
122) NTC0120L NTC 20A SCK-0120 XPM-900 PC 2
123) RS0500122005 1.2 K 5W SQP TYPE PC 1
124) W2010G130050 1015#14 BLACK XPM-900U PC 1
125) W2010G180059 1015#14 WHITE XPM-900U PC 1
126) FAD012080001 SP802512H L=350m/m+XH PC 2
127) FH630207D FUSE HOLD CQ-207D PC 1
128) FS630ULC120F FUSE 6x30 FAST/GLASS U/C 12A PC 1
129) FTSF-006 PLASTIC FOOT SF-006 PC 4
130) IBXPM900—GI MANUAL XPM-900 (GEMINI) PC 1
131) KB1819BL0001 KNOB 18x19 BLACK XPM-900 PC 2
132) NTM8x17x080B NUT 5/16 (0A0220-310005) PC 1
133) PB420215 PLOY BAG 8.5"x16.5"X0.05 PC 1
134) PT160———2 TRANS. 160m/m XPM-900U 120V PC 1
135) SPK1047R2001 WIN-1047R2 R/B XPM-900 PC 1
136) SPK1047R2002 WTN-1047R2 B/R XPM-900 PC 1
137) SPKCOVER—1 WIN-1047R2 COVER BLACK XPM-900 PC 1
138) SPKCOVER—2 WIN-1047R2 COVER RED XPM-900 PC 1
139) SR01MS3x042B MST 3x4 BLACK(1JPH1C-030424) PC 2
140) SR01MS3x061B MS 3x6 BLACK(1JBHMC-030604) PC 1 0
141) SR01MS3x081W MS 3x8 (1JPHMC-030800) PC 1
142) SR01MS4x061W MS 4x6 (PLATING) PC 1
143) SR01MS3x121B MS 3x12 BLACK PC 1
144) SR01MS4x082B MST 4x8 BLACK (1JBH1C-040824) PC 1 6
145) SR01TP3x063B TP 3x6 BLACK (1JBHCC-030625) PC 6
146) SR01TP3x103B TP 3x10 BLACK (1JBHCC-031024) PC 4
147) SR03TP4x084B FMT+W TP 4x8 (1JBP6C-040825) PC 1 4
148) SR10MS8x751B 5/16x3" (1ATKMO-31C004) PC 1
149) SWP————9 R22-22B-11B XPM-900 PC 1
150) VR16A1031501 16K4x1 L-15 XPM-900 PC 2
151) W2010G445100 1015#14 BLACK XPM-900U PC 1
152) W2010G505109 1015#14 WHITE XPM-900U PC 1
153) W2010I12510A 1015#18 GR+YL PC1800 PC 1
154) W20110120100 1015#14 BLACK XPM-900U PC 1
155) W5010A370032 2852#26 RED XPM-900 PC 1
156) W5010A460038 2852#26 GRAY XPM-900 PC 1

Page17
1) 102056543301 SPACER XPM-900 PC2
2) 102119214703 CARTON XPM-1200 PC1
3) 102260018003 EXT.CARTON XPM-1200 PC1
4) 103012005700 SPACER 1200x570m/m PC1
5) 105011008501 HOLDER XPM-900 PC2
6) 105032409601 WALL XPM-900 PC1
7) 105034608501 SILD PANEL XPM-900 PC2
8) 105242608605 BACKBOARD XPM-1200 PC1
9) 105343431801 TOPCOVER XPM-900 PC1
10) 105443431701 BOTTOMCABI XPM-900 PC1
11) 107042002501 AIRFILTER 420x25m/m XPM-900 PC1
12) 107042004003 PVCCOVER XPM-1200 PC1
13) 1070ACS03501 ACS-3.5PVCRED PC5
14) 1070KG-010 M0VEABLEBUSHINGKG-010 CM2
15) 1070SCB-10 SPACERSUPPORTSSCB-10XPM-900 PC4
16) 1070SS-6 SELFRETATININGSPALERSSS-6 PC1
17) 1070YJ-98 NYLONCLAMPERYJ-98 PC12
18) AL201AL50101 AL201/AL501 SJTW-A14AWG 6FT PC1
19)AO016D130 3P AC INLET AC-016D130 XPM-900 PC1
20) 105006400001 6.4m/m PIN PC6
21) 106201302001 HEAT SINK BLACK 13x20 XPM-900 PC1
22) 106203003003 RECTIFERHEATSINK XPB-1600 PC1
23) 1070LED-3.5- LEDSPACERSUPPORTLED-3.5 PC9
24) 700KBP060002 RECTIFIER KBP062A600V PC1
25)700MP3504W02 RECTIFIERMP3504W35A400V PC1
26)CCN0A101250K CERAMICCAP100P250V PC6
27)CCN0A680500J CERAMICCAP68P500VNPO5% PC4
28) COIL16115T6L COIL 1.6x10.1x11.5T-6L XPM-900 PC2
29)ECL06800100M ELEC CAP6800u100v PC4
30)ECS00010050M ELECCAP10u50v PC4
31)ECS00100025M ELECCAP100u25v PC4
32)ECS00100100M ELECCAP100u100v PC4
33)ECS00220016M ELECCAP220u16v PC6
34)ECS01000025M ELECCAP1000u25v PC1
35)ECS02200025M ELECCAP2200u25v PC1
36) ICNJM3404AD- ICNJM3404AD PC2
37) ICTL072CP IC TL072CP PC1
38) JS1001025003 BASE3P2.5m/m PC2
39) JS1001025012 BASE12P2.5m/m PC1
40) JS1001R25002 BASE 2P JS-1001R-02 PC2
XPM-1200

Page18
41) LDG050210030 LED5m/mGREEN PC5
42) LDR050410030 LDE5m/mRED PC2
43) LDY050610030 LDE5m/mYELLOW PC2
44) MJ0860250900 CONNOCJACK086-25-90 PC2
45)MJCPJ-065—- JACK CPJ-065 XPM-900 PC2
46)MPMEA104250K MEA .1u 250V 10% PC6
47)MPMEF104250K MEF .1u 250V 10% PC2
48)NTM3x07x030Y NUT 3m/m W/S (0J0010-030001) PC1
49) RC0200A47005 RESISTORS 4.7 ohm 2W M PC2
50) RC0201000005 RESISTORS10ohm2W M PC2
51) RC0202230005 RESISTORS 22K2W M PC2
52) RC0204720005 RESISTORS 4.7 K 2W M PC2
53) RC0205620005 RESISTORS 5.6 K 2W M PC2
54)RL832——12 832-1C-C-12D XPM-900 PC2
55)SR01MS3x061B MS 3x6 BLACK PC1
56)SR01TP4x204Y TP4x20 (1JBH6C-042021) PC1
57)SWL————1 SS004-P2430Em-PC10 XPM-900 PC1
58)SWS————1 SS004-P022BY-PF8 PC1
59)TRMJE340—0 MJE340 PC2
60)TRMJE350—0 MJE350 PC2
61)TRMPSA13—0 TRMPSA13 PC2
62)TRTIP122—0 TIP122 PC1
63)TRZ0103——0 TRIAC Z0103 MA1A600V RR-15 PC2
64) W20105135205 1015#14GREEN XPM-900 PC1
65) W20105185205 1015#14GREEN XPM-900 PC1
66) W20105235208 1015#14 GRAY XPM-900 PC1
67) W20105375202 1015#14 RED XPM-900 PC1
68)W2120A3000BB 1007#26 MIX XPM-900 PC1
69)WS204x10x07W SPRING W/S.M4-L(2JS100-040050) PC1
70) 106219207601 HEAT SINK 192x76x60 XPM-900 PC2
71)PTH9M222—E2 PTH9M04BE222TS2F333 XPM-900 PC2
72)PTH9M471—H1 PTH9M04BH471TS2F333 XPM-900 PC2
73)SR01MS3x061B MS 3x6 BLACK PC4
74)SR01MS3x121B MS 3x12 BLACK PC8
75)SR01TP3x103B TP 3x10 BLACK PC4
76)SR03TP4x084B FMT+WTP4x8 BLACK PC4
77)TRBUZ901NDP0 BUZ901NDPMOSFET XPM-1200 PC4
78)TRBUZ906DP-0 BUZ906DP MOSFET XPM-1200 PC4
79)WS132x08x10W 3.2x0.8x10 (2IFA032-081000) PC8
80)WS203x08x05W SPRING W/S.M3-L(2JS100-030050) PC12

Page19
81)2SA970BL—0 TR 2SA970 BL PC10
82)2SC2240BL—0 TR 2SC2240BL PC4
83)6003501950— XPM-900MAINPCBOARDT=2oz PC1
84) 700033050001 ZENER3.3v 500mw PC6
85) 700075050001 ZENER7.5V500mw PC1
86) 700120050001 ZENER12V500mw PC6
87) 700150050001 ZENER15V500mw PC1
88) 700150100001 ZENER15V1W PC2
89) 7001N4004051 DIODE1N4004 PC6
90) 7001N4148051 DIODE1N4148 PC13
91)MCT0A102100J MYLAR CAP .001u T PC2
92)MCT0A153100J MYLAR CAP .015u T PC2
93)MCT0A182100J MYLAR CAP .0018u T PC2
94)MCT0A473100J MYLAR CAP .047u T PC1
95)MPMSC104100J MSC .1u 100V 5% T PC15
96) RC0031010005 RESISTORS 100 ohm 1/4W T PC4
97) RC0031020005 RESISTORS 1 K 1/4W T PC21
98) RC0031030005 RESISTORS 10 K 1/4W T PC16
99) RC0031040005 RESISTORS 100 K 1/4W T PC2
100) RC0031050005 RESISTORS 1 M 1/4W T PC1
101) RC0031520005 RESISTORS 1.5 K 1/4W T PC2
102) RC0032020005 RESISTORS 2 K 1/4W T PC3
103) RC0032210005 RESISTORS 220 ohm 1/4W T PC2
104) RC0032230005 RESISTORS 22 K 1/4W T PC2
105) RC0033030005 RESISTORS 30 K 1/4W T PC4
106) RC0033040005 RESISTORS 300 K 1/4W T PC2
107) RC0033320005 RESISTORS 3.3 K 1/4W T PC4
108) RC0034700005 RESISTORS 47 ohm 1/4W T PC4
109) RC0034730005 RESISTORS 47 K 1/4W T PC4
110) RC0035110005 RESISTORS 510ohm 1/4WT PC4
111) RC0036830005 RESISTORS 68 K 1/4W T PC4
112) RC0038210005 RESISTORS 820 ohm 1/4W T PC2
113) RC0038220005 RESISTORS 8.2 K 1/4W T PC2
114)RC0050A10005 RESISTORS 1 ohm 1/2W T PC1
115) RC0053030005 RESISTORS 30 K 1/2W T PC2
116) RC0054730005 RESISTORS 47 K 1/2W T PC2
117)RM0030K47501 RESISTORS 475 ohm 1/4W T PC2
118)RM00310K0001 RESISTORS 10K 1% 1/4W T PC8
119) 105006400001 6.4m/m PIN PC2
120)6000680600— XPM-900POWERPCBOARDT=oz PC1

Page20
121)MPMPX473275K MPX .047u275VAC10% PC1
122)NTC0120L—— NTC 20A SCK-0120 XPM-900 PC2
123) RS0500122005 1.2 K 5W SQP TYPE PC1
124)W2010G130050 1015#14 BLACK XPM-900U PC1
125)W2010G180059 1015#14 WHITE XPM-900U PC1
126) FAD012080001 SP802512HL=350m/m+XH PC2
127)FH630207D—- FUSEHOLDCQ-207D PC1
128)FS630ULC150F FUSE 6x30FAST/CERAMICU/C15A PC1
129)FTSF-006—— PLASTIC FOOTSF-006 PC4
130)IBXPM900—GI MANUAL XPM-900 (GEMINI) PC1
131) KB1819BL0001 KNOB18x19BLACK XPM-900 PC2
132)NTM8x17x080B NUT 5/16 (0A0220-310005) PC1
133)PB420215—— PLOY BAG 8.5"x16.5"X0.05 PC1
134)PT160———4 TRANS.160m/mXPM-1200U120V PC1
135)SPK1047R2001 WIN-1047R2 R/B XPM-900 PC1
136)SPK1047R2002 WTN-1047R2 B/R XPM-900 PC1
137)SPKCOVER—1 WIN-1047R2COVERBLACKXPM-900 PC1
138)SPKCOVER—2 WIN-1047R2COVERRED XPM-900 PC1
139)SR01MS3x042B MST3x4BLACK(1JPH1C-030424) PC2
140)SR01MS3x061B MS3x6 BLACK(1JBHMC-030604) PC10
141)SR01MS3x081W MS 3x8 (1JPHMC-030800) PC1
142)SR01MS3x121B MS 3x12 BLACK PC1
143)SR01MS4x061W MS 4x6 (PLATING) PC1
144)SR01MS4x082B MST 4x8 BLACK (1JBH1C-040824) PC16
145)SR01TP3x063B TP 3x6 BLACK (1JBHCC-030625) PC6
146)SR01TP3x103B TP 3x10 BLACK (1JBHCC-031024) PC4
147)SR03TP4x084B FMT+W TP 4x8 (1JBP6C-040825) PC14
148)SR10MS8x751B 5/16x3" (1ATKMO-31C004)V3000 PC1
149)SWP————9 R22-22B-11B XPM-900 PC1
150) VR16A1031501 16K4x1 L-15 XPM-900 PC2
151)W2010G445100 1015#14 BLACK XPM-900U PC1
152)W2010G505109 1015#14 WHITE XPM-900U PC1
153) W2010I12510A 1015#18GR+YL PC1
154) W20110120100 1015#14 BLACK XPM-900U PC1
155)W5010A370032 2852#26 RED XPM-900 PC1
156)W5010A460038 2852#26 GRAY XPM-900 PC1
157)WDGEMINI—— GEMINIWARRANTYCARD PC1
158)WS407x03x09Y EXTTOOTHW/S.3m/m PC1