Gemini GEM-RP8 User manual

ARMED
COMPUTERIZED SECURITY SYSTEM
STATUS
I
H 1 2 3 4 5 6 7 8
A 1 2 3
B 4 5 6
C 7 8 9 0
E
F
G
J
OPERATING GUIDE for your
GEM-RP8 KEYPAD
© NAPCO 2003 DESIGN PATS. PENDING
OI219E 7/03

Congratulations on your purchase of an advanced GEMINI-RP8 keypad. Meticulously developed by a leading
manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind &
incorporates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide
all those operating it with very easy, intuitive use. Please carefully review the information contained in this manual, so that you
and all potential users of the system familiarize yourselves with its operation, and can therefore take full advantage of GEMINI’s
many convenient features and amenities.
Your system consists of a control panel (a computer housed within a white metal panel enclosure), one or more GEMINI
Decorator Keypads for controlling the system, and various security detection devices. These detection devices are divided
among separate areas known as “zones”, set up throughout your premises. Each zone number corresponds to a Zone light on
your Keypad’s display area.
When a zone’s number is ON (or lit), it indicates that one or more detection device(s) assigned to that area are active or open.
For example, if Zone 1 is the front door, and it is open, the 1on the keypad display will be lit. If zone 2 is a motion detector, and
there is movement in that area, 2will light. Depending upon the actual layout your security professional has chosen to properly
protect your premises, each zone may function a little differently: The zone protecting your front door may be programmed as
an Exit/Entry zone to allow you time to enter the premises and disarm the system, without inadvertently sounding the alarm.
Alternatively, a zone protecting a window could be designated as an “instant” zone, so that if it is entered or opened while the
system is on/armed, there will be an immediate alarm.
Your easy GEMINI Keypad puts super-simple system control at your fingertips. Most keypad commands involve
entering your four digit User Code. This includes Arming (or activating) and Disarming (or deactivating) the system. Simply put,
ARMED means the system is ON; DISARMED means the system is OFF. If the system is OFF and you want to turn it ON, just
enter your Code. To turn the system back OFF, enter your code again. It’s easy, just always remember, in the event of an
alarm, entering your User Code will silence all Sirens. Your keypad is your command and status center, it keeps you
informed visibly—using its zone and status lights, and audibly—using its built-in keypad sounder. For more information, please
see Keypad Controls and Indicators on page 4.
2
INTRODUCTION

3
Important - Test Your System Weekly!
1Bell / Battery Test
Test your bell or siren by pressing Afollowed by 1.
This will cause the bell, or siren to sound for 2 seconds and also
initiate a test of the battery.
2Zone Test
Walk throughout the premises, opening each protected door or
window, and activating each motion sensor. Check the keypad to
see that each respective zone number displays in the window.
3Central Station Communication Test
This test should only be performed on weekends or at a time
designated by your alarm company.
1. Notify Central Station of the impending test.
2. Secure all zones to light the Status Light on your keypad.
3. Enter your User Code followed by Dto Arm the system.
4. Violate your alarm by opening a window / door etc.
5. The siren or bell should sound and the system will send the alarm
signals to the Central Station.
6. Enter your User Code followed by Dto silence the alarm.
7. Call Central Station to insure that the alarm signals were received
properly.
System Information
Central Station Phone Number:___________________
Central Station Account Number: _________________
For Service Call: ______________________________
Entry Delay: __________________________________
Exit Delay: ___________________________________
Alarm Time-out:_______________________________
TABLE OF CONTENTS
TABLE OF CONTENTS
KEYPAD CONTROLS & INDICATORS ..................................................4
ARMING: SETTING THE ALARM WHEN LEAVING.............................5
ARMING: PROTECTING YOURSELF AT HOME .................................6
EMERGENCY CONDITIONS..................................................................7
TURNING OFF THE ALARM (DISARMING) WHEN RETURNING .......8
FIRE PROTECTION ................................................................................9
FUNCTION MENU...................................................................................11
SYSTEM TROUBLES..............................................................................12
PROGRAMMING (OPTIONAL)...............................................................14
GLOSSARY .............................................................................................15
LIMITED WARRANTY .............................................................................16

ARMED
COMPUTERIZED SECURITY SYSTEM
STATUS
I
H
GEMINI
1 2 3 4 5 6 7 8
A 1 2 3
B 4 5 6
C 7 8 9 0
E
F
G
J
4
Status Light will light when all zones are secure
and system is ready to be Armed.
AC Light will light to indicate
that AC Power is present.
Trouble Light Hwill light and the Keypad
sounder will pulse to indicate that a system
trouble is present. (See System troubles, Page 12)
Zone Lights (1 through 8) will light to indicate
that the corresponding Zone is open, and will
flash to indicate a zone in alarm.
Armed Light will light when system is Armed,
and will flash when system is in Alarm
Press Cto reset Fire Zone, clear miss-
entered codes, reset Alarm Memory, etc.
Fire Alarm Light Iwill flash and the Keypad
sounder will beep when system is in a Fire Alarm
Condition (See Silencing a fire Alarm, Page 8)
Emergency Keys Press simultaneously
to signal an emergency condition.
Press 7+Gfor Fire Emergency,
8+Gfor Auxiliary Emergency or
9+Gfor Police Emergency.
(Programmable)
To Bypass a zone, press Band the zone
number to be bypassed, and then Arm system.
Press Afollowed by the corresponding
Function number to enable special functions and
options. (See Special Functions, Page 11)
Numerical
Keys 1-9, 0.
Used to
enter User
Codes, Zone
numbers,
etc.
Press E
to bypass all
interior
protective
devices such
as motion
sensors, etc.
Press
Fto
remove entry
delay from
the Exit/
Entry door.
Press D
after entering
User Code
when Arming
or Disarming
System.
KEYPAD CONTROLS & INDICATORS

Arming Your System When Leaving
1 Before arming your system, make sure the green Status light is ON. This indicates that all of your protective zones are
secure. If any zones are open, the corresponding Zone number will be lit. Secure these zones before proceeding. If any
zones cannot be secured, see Bypassing zones below.
2 Enter your user code and press D.The green Status light will go out, the red Armed light will light.
•If you make a mistake entering your code, press C, re-enter the code and press D.
•If FIRE Iis lit, the Fire zone has not been properly reset. Press C, enter your user code and press D.
(See Silencing a Fire Alarm, page 8)
3 Leave the premises through the Exit/Entry door. If the keypad gives a steady tone you have taken too long. Enter your code
again to disarm system and then re-enter code and leave.
Easy Arm
The optional Easy Arm feature allows the system to be armed by simply pressing D.This will allow the easy arming of the
system by someone who is not a regular system user.
Bypassing Zones
If an open zone cannot be immediately fixed it can be left unprotected, or bypassed ,while the rest of the system is Armed.
To bypass a zone:
1 Press Bfollowed by the number of the zone to be bypassed. The bypassed zone’s number will flash slowly.
2 Enter your user code and press D.The green Status light will go out and the red Armed light will light.
3 Leave the premises through the Exit/Entry door.
When the system is subsequently disarmed, all bypassed zones will be reset, ready to be armed again. If it is necessary to
bypass any inoperative zone(s), it is important to have the zone(s) repaired as soon as possible.
5
ARMING: SETTING THE ALARM WHEN LEAVING

Protecting Yourself While at Home
1 Before arming your system, make sure the green Status light is ON. This indicates that all of your protective zones are
secure. If any zones are open, the corresponding zone number will be lit. Secure those zones before proceeding.
2 Enter your User Code and press D.The green Status light will go out, and the red Armed light will light.
3 Before your exit delay expires, press Bto bypass any interior zones, deactivating devices such as motion sensors, and
allowing free movement throughout the premises. The Zone light of any bypassed zones will flash slowly.
Your system may have been programmed for Automatic Interior Bypass, in which case it will recognize that you have not left
the premises and will automatically bypass any interior zones.
Instant Mode
Pressing Fwill cancel the Entry delay, activating the “Instant” mode. This is typically done in the evening when all family
members are home for the night. Instant Mode can be activated at any time after the system has been armed. The red
Armed light will flash rapidly while in the Instant Mode.
Easy Exit (optional)
Your System may have been programmed to allow Easy Exit, which allows a user to exit the premises with the system
armed. By pressing Afollowed by 0, the protection is removed from the Exit/ Entry zone for 3 minutes.
This will allow, for example, an early morning commuter to exit the house in the morning, without having to disarm and rearm
the system, waking the family.
Arming with a System Trouble Present (TROUBLE His lit)
If the GEM-P800 has a system trouble present, TROUBLE Hwill be lit and the keypad sounder pulsing. If you cannot
immediately clear the trouble, the system can still be armed. Simply press Afollowed by 4to view the trouble.
Press Eto view any other troubles, and exit the TROUBLE mode when done. Enter your User Code and press Dto
arm the system. For more information, refer to page 12. Note: System troubles should be repaired as soon as possible.
6
ARMING: PROTECTING YOURSELF AT HOME

Emergency Buttons 789G
The three sets of emergency buttons, if programmed, are always active whether the system is armed
or disarmed. Discuss these Buttons with your installer. The emergency signal will only be activated
when the two respective buttons are pressed at the same time.
Fire Alarm: Simultaneously press7+Gto sound a fire alarm, and to alert the central
station of a fire emergency, if so programmed.
Auxiliary Alarm: Simultaneously press8+Gto alert the central station of an auxiliary
emergency, if so programmed. (The nature of this emergency alarm is to be determined by the
installer)
Police Emergency: Simultaneously press9+Gto sound a police emergency alarm,
and to alert the central station of a Police emergency, if so programmed.
7+G
Fire Emergency
Enabled?
Yes !No !
8+G
Auxiliary Emergency
Enabled?
Yes !No !
Ambush Alarm
In the event that you are forced by an intruder to disarm your system, the ambush alarm can be
activated. Disarming the system with the Ambush Code will cause the system to disarm and
simultaneously send a silent ambush alarm signal to Central Station. If your system has the Ambush
feature enabled, the code assigned as the User 8 code will function as your Ambush Code.
9+G
Police Emergency
Enabled?
Yes !No !
Ambush Alarm
Enabled?
Yes !No !
EMERGENCY CONDITIONS

Disarming Your System when Returning
1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry
Delay time expires.
2 Enter your User Code and press D. The red Armed light will go out, indicating that the system has been disarmed.
Note: If you make a mistake entering your code, press Cand re-enter the code, followed by D.
Alarm Indication
If the Red Armed light is flashing rapidly, an alarm occurred while you were away. Proceed with caution!
For your own protection, leave immediately and call authorities from a neighbors phone .
Silencing an Alarm
In the event the system goes into alarm due to a violated burglary zone, the siren and the keypad sounder will activate and the number of the
zone in alarm will flash in the display. To silence the system, enter your User code followed by D.
The keypad sounder and siren will silence, but the zone in alarm will continue to flash. Press Cto reset this alarm memory.
Silencing a Fire Alarm
In the event that the Fire alarm activates due to a violated smoke or fire detector, the bell or siren will sound a distinct pulsating tone. FIREI
on the keypad will be flashing, and the keypad sounder will emit a pulsing tone. If a Fire Alarm does occur:
1 If a fire is in progress, evacuate the premises immediately! Call the Fire Department from an outside phone.
2 If there is no evidence of a fire, enter your User Code followed by D. The bell or siren will silence, and FIREIwill stop flashing, but will still
be lit.
3 Determine which device went into alarm. If you are protected by smoke detectors, the light on the active detector will be lit. Once it is
determined which smoke detector is in alarm, press Cto reset the fire zone.
4 If the Fire zone has reset properly, FIREIshould go out in approx. 30 seconds. If it does not go out, press Cagain in a few minutes. If
it still does not go out, call for service.
Abort Delay
Ask your installer which of your zones have Abort Delay, a delay that enables you to reset the system before it communicates to the central
station. Your system has a SIA CP-01 required Abort Delay of 30 seconds. It may be removed or increased up to 45 seconds (at your op-
tion) by consulting with your installer.
8
TURNING OFF THE ALARM (DISARMING) WHEN RETURNING

Preparing a Fire Escape Plan
Even with the most advanced fire alarm system, adequate protection requires an escape plan.
To prepare your plan, draw floor plans of your building (space is provided on the next page). Show two exits-a front or
back door and a window from each room. (Make sure each window works. You may need a special fire-escape ladder if
the window is high up). Write down your outside meeting place.
Family Rehearsal
Rehearse each of the following activities:
1 Everyone in his room with the doors closed.
2 One person sounds the alarm.
3 Each person tests his door.
4 Pretend that the door is hot and use the alternate escape exit.
5 Everyone meets outdoors at the assigned spot.
Important! - Read Carefully
Discuss each of these escape procedures with all those who use
the building.
1 In a residence, sleep with the bedroom door closed.
2 When the fire alarm signals, escape quickly. Do not stop to pack.
3 Test the door. If it is hot, use your alternate route through the window.
If the door is cool, brace your shoulder against it and open it cautiously. Be ready to slam the door if smoke or heat
rushes in. Crawl through the smoke, holding your breath. Close the doors again on leaving to help prevent the fire from
spreading.
4 Go to your specific outdoor meeting place so you can see that everyone is safe.
5 Call the Fire Department from a neighbor’s telephone.
Would You Like More Safety Information?
For more information on home fire detection,
burn safety, and home fire safety, write to:
National Fire Protection Association
Public Affairs Dept. 05A
Batterymarch Plaza
Quincy, MA 02269
9
FIRE PROTECTION

10
Floorplan
Draw a plan of your premises below.
FIRE PROTECTION

By pressing Afollowed by the the appropriate key, (do not press simultaneously) these special functions and
features can be enabled:
Easy Arm (when system is disarmed)
The Easy Arm feature allows the system to be armed by
pressing Afollowed by 0. This will allow the easy
arming of the system by someone who is not a regular
system user.
Easy Exit (when system is armed)
This function (if programmed) allows an occupant to leave
the premises without disarming the system. Pressing
Afollowed by 0while the system is armed will
start a 3-minute period, during which you can leave through
the Exit/ Entry door.
Bell / Battery Test
Pressing Afollowed by 1will cause the bell, or
siren to sound for 2 seconds. This will also initiate a test of
your battery to make sure it is adequately charged. The
P800 also performs an automatic battery test every 24
hours.
Access Output
If programmed, pressing Afollowed by 3will
activate the Access Output which may be configured to
open a door strike, turn on lighting, or activate some other
special feature your installer has provided.
Display System Trouble
Pressing Afollowed by4when TROUBLE His lit
will cause the system to display any current system troubles.
Pressing Ewill exit the Display System Trouble Mode.
Chime Mode On / Off
Pressing Afollowed by 5will activate / deactivate
the door chime. Activating this feature will cause any door to
beep the keypad sounder when it is opened.
Program Mode
Pressing Afollowed by8will enable the “Program
Mode”, which will allow you to program and erase user
codes. (see Programming user codes, page 14).
Keypad Sounder On / Off
Pressing Afollowed by 9will deactivate / activate
the keypad sounder, depending on its present state. By
deactivating the sounder on a keypad installed in a bedroom,
for example, you will only turn off that keypad’s sounder. All
other keypads on the system will still sound normally.
11
FUNCTION MENU

12
The Control Panel is constantly monitoring its own components, as well as all critical services, such as AC power and the
telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does
occur, it will caution you by lighting the TROUBLE Hlight and beeping the keypad buzzer.
If you cannot immediately clear the system trouble, the system can still be used. Simply press Afollowed by 4to view
the trouble as described below, and then arm the system.
To determine the nature of the trouble, press Afollowed by 4, count the number of keypad beeps and observe the
number of the illuminated zone. Refer to the following table to determine the cause of the trouble. If there is more than one
trouble to view, pressing Ewill scroll to the next trouble, and then exit the TROUBLE Hmode if there are no more troubles
to view.
Keypad Beeps or
HFlashes
Zone light
ON
System Trouble
Condition
Action
1 Beep 1 AC Power Failure This trouble will occur if AC power is not present. Make sure system transformer is
plugged into AC receptacle and check the circuit breaker, otherwise call installing
company for service.
1 Beep 2 Low Battery If there has been a recent power failure, the battery may be partially depleted and must
be recharged by the control panel. If the trouble does not go away in 24 hours, call
installing company for service.
1Beep 3 Communication
Failure
The system was not able to report to central station. If this is due to a temporary
interruption in the telephone service, the trouble can be cleared when the service is
restored by pressing Afollowed by4again to view the trouble, and then
pressing Eto exit. Otherwise, call installing company for service.
1 Beep 4 Telephone Line Cut The telephone line has failed. If telephone service has been temporarily interrupted,
the trouble will clear it is when restored. Otherwise, call installing company for service.
2 Beeps 1 Bell/Siren Trouble There is a problem with the Bell or Siren. Call installing company for service.
HSYSTEM TROUBLES

13
Keypad Beeps or
HFlashes
Zone light
ON
System Trouble
Condition
Action
2 Beeps 2 Fire Trouble A problem has been detected in the Fire Circuit.
Call installing company for service.
2Beeps 3 Wireless Receiver
Trouble
A problem has been detected with the wireless receiver.
Call installing company for service.
2 Beeps 4 Wireless Receiver Jam A problem has been detected with a wireless receiver.
Call installing company for service.
3 Beeps 1-8 Wireless Transmitter
Low Battery
The battery in a wireless transmitter is low and should be replaced. This transmitter is
on the zone corresponding to the number of the lit zone light. The replacement battery
for the GEM-Trans2 door/window transmitter, GEM-PIR motion detector and GEM-GB
glass break detector is the Duracell DL123A 3 volt lithium. (2 required for the GEM-PIR
and GEM-GB). The GEM-DT Dual Technology Sensor requires 4 C cell alkaline
batteries. Warning: Replace batteries only with the same type as specified above. Use
of another battery may present a risk of fire or explosion. Do not recharge or
disassemble battery, or dispose of in fire.
4Beeps 1-8 Wireless Transmitter
Supervisory Failure
A problem has been detected with a wireless transmitter.
Call installing company for service
5 Beeps 1-4 Wireless Smoke
Detector Low Battery
The battery in a wireless smoke detector is low and should be replaced. This wireless
smoke detector should be marked with a number corresponding to the number of the lit
zone light. The replacement battery is the Duracell MN1604 9 Volt Alkaline(2 required).
Warning: Replace batteries only with the same type as specified above. Use of another
battery may present a risk of fire or explosion. Do not recharge or disassemble battery,
or dispose of in fire.
6 Beeps 1-4 Wireless Smoke
Detector Supervisory
Failure
A problem has been detected with a wireless smoke detector.
Call installing company for service.
7 Beeps 1-6 Zone Trouble Call installing company for service.
HSYSTEM TROUBLES

Your Installer has assigned a User 1 Code which can be used to not only Arm and Disarm the system, but also to enter the User
Program Mode, where you can program other user codes. The following explains how you will use this code to program or erase
additional user codes.
Entering the User Program Mode
Press Afollowed by 8and enter the User 1 code folowed by D.The Armed, Status and Hlights will flash, and the
keypad will beep 4 times. You are now in the User Program mode. Zones 1 through 8 will light to indicate any User Codes
presently programmed.
Programming / Reprogramming User Codes
1 Press the User number to be programmed. (For example, press 2 to program the User 2 code).
The keypad will beep 2 times and the corresponding Zone will flash to indicate the user number you are about to program.
2 Press in the 4 digits of the new User 2 code, the keypad will beep 4 times.
3 If there are more user codes to be programmed, return to step 1 above, otherwise, go to Exiting the User Program Mode below.
Erasing a User Code
1 Press the User number to be erased. The keypad will beep 2 times and the corresponding Zone light will flash to indicate the
user number you are about to erase.
2 Press F. The zone light will go out to indicate that the user code has been erased.
3 If there are more user codes to be erased, return to step 1 above, otherwise, go to Exiting the User Program Mode below.
Exiting the User Program Mode
When you are finished programming or erasing User codes, press Cto Exit the User Program Mode.
14
PROGRAMMING (OPTIONAL)

Ambush Code - In the event that you
are forced by an intruder to disarm your
system, this special code can be used
to disarm the system, and
simultaneously send a silent alarm to
Central Station. If your system has the
Ambush feature enabled, the code
assigned as the User 8 code will
function as your Ambush Code.
Arming / Disarming - Turning the
system on or off by entering your user
code at the keypad, followed byD.
Auto Interior Bypass - A feature which
allows the system to recognize when
you have not left the premises and
automatically bypass any interior zones,
deactivating devices such as motion
sensors, allowing free movement
throughout the premises.
Battery - A backup source of power to
provide protection for a limited time in
the event of a power failure.
Bypass - the manual or automatic
removal of one or more protection zones
from the system. PressBand then
the zone number to bypass a zone.
Central Station - Monitors alarm,
emergency and trouble reports from the
alarm system and notifies proper
authorities.
Chime - a keypad beep which indicates
that a door has been opened while the
system is disarmed.
Easy Exit - Allows an occupant to leave
the premises without disarming the
system. Pressing Aand then
0while the system is armed will
permit exit by removing the protection
on the Exit/Entry door for 3 minutes.
Exit/Entry Delay - The amount of time
you are allowed to enter and leave the
premises when the system is armed.
Exit/Entry Zone - A zone which will
allow you to enter and leave the
premises when the system is armed.
Instant Protection - Arming without
Entry Delay while remaining on the
premises. (Press Fwhile armed).
Keypad Sounder - A local warning
device at the keypad to alert that Entry
delay has started.
System Trouble - A problem has been
detected in the system which may
prevent it from working properly.
TROUBLEHwill be lit to indicate a
system trouble.
User Code - A four digit code which is
used to arm and disarm the system from
the keypad.
User 1 Code - A four digit code which
can be used to program, re-program
and erase user codes, as well as arm
and disarm the system from the keypad.
Zone - An area which is protected by a
security device. Your front door may be
designated as Zone 1, while the living
room motion detector may be Zone 2.
Refer to the Zone Label on your keypad
for the Zone Identification of your
system.
15
GLOSSARY

NAPCO LIMITED WARRANTY
THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC.
This equipment generates and uses radio-frequency energy and, if not installed and used properly, that
is, in strict accordance with the manufacturer's instructions, may cause interference to radio and
television
reception. It has been type tested and found to comply with the limits for a Class-B computing device in
accordance with the specifications in Subpart J of Part 15 of FCC Rules, which are designed to provide
reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: reorient the receiving antenna; relocate the computer with respect to the receiver;
move the computer away from the receiver; plug the computer into a different outlet so that computer and
receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions. The user may find the following booklet prepared by the Federal Communications
Commission helpful: “How to Identify and Resolve Radio-TV Interference Problems”. This booklet is
available from the U.S. Government Printing Office, Washington, DC 20402; Stock No. 004-000-00345-4.
NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects
in materials and workmanship for thirty-six months following the date of manufacture. NAPCO will, within
said period, at its option, repair or replace any product failing to operate correctly without charge to the
original purchaser or user.
This warranty shall not apply to any equipment, or any part thereof, which has been repaired by others,
improperly installed, improperly used, abused, altered, damaged, subjected to acts of God, or on which any
serial numbers have been altered, defaced or removed. Seller will not be responsible for any dismantling or
reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY
OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS
IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF NAPCO.
Any action for breach of warranty, including but not limited to any implied warranty of merchantability, must
be brought within the six months following the end of the warranty period.
IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF
THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.
In case of defect, contact the security professional who installed and maintains your security system. In
order to exercise the warranty, the product must be returned by the security professional, shipping costs
prepaid and insured to NAPCO. After repair or replacement, NAPCO assumes the cost of returning products
under warranty. NAPCO shall have no obligation under this warranty, or otherwise, if the product has been
repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to accident,
nuisance, flood, fire or acts of God, or on which any serial numbers have been altered, defaced or removed.
NAPCO will not be responsible for any dismantling, reassembly or reinstallation charges.
This warranty contains the entire warranty. It is the sole warranty and any prior agreements or
representations, whether oral or written, are either merged herein or are expressly cancelled. NAPCO
neither assumes, nor authorizes any other person purporting to act on its behalf to modify, to change, or to
assume for it, any other warranty or liability concerning its products.
In no event shall NAPCO be liable for an amount in excess of NAPCO's original selling price of the product,
for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any
failure of the product. Seller's warranty, as hereinabove set forth, shall not be enlarged, diminished or
affected by and no obligation or liability shall arise or grow out of Seller's rendering of technical advice or
service in connection with Buyer's order of the goods furnished hereunder.
NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to, any or all of the following; criminal
tampering, electrical or communications disruption, it is possible for the system to fail to perform as
expected. NAPCO does not represent that the product/system may not be compromised or circumvented; or
that the product or system will prevent any personal injury or property loss by burglary, robbery, fire or
otherwise; nor that the product or system will in all cases provide adequate warning or protection. A properly
installed and maintained alarm may only reduce risk of burglary, robbery, fire or otherwise but it is not
insurance or a guarantee that these events will not occur. CONSEQUENTLY, SELLER SHALL HAVE NO
LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS BASED ON A
CLAIM THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer should in turn advise the
consumer to take any and all precautions for his or her safety including, but not limited to, fleeing the
premises and calling police or fire department, in order to mitigate the possibilities of harm and/or damage.
NAPCO is not an insurer of either the property or safety of the user's family or employees, and limits its
liability for any loss or damage including incidental or consequential damages to NAPCO's original selling
price of the product regardless of the cause of such loss or damage.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or
limitation of incidental or consequential damages, or differentiate in their treatment of limitations of liability for
ordinary or gross negligence, so the above limitations or exclusions may not apply to you. This Warranty
gives you specific legal rights and you may also have other rights which vary from state to state.
NAPCO Security Systems, 333 Bayview Avenue, Amityville, NY 11701 © NAPCO 2003