Instructions for use
Display icon definition
16 sets of body temperature memory data queries
On the boot state, press the "up" or "down" button, LCD display the first
memory value; each click the "+" or "-" button, display the memory number
plus 1 or minus 1, a total of 16 groups of memory data.
Safety instructions
Human body temperature measurement
After the batteries are installed, press the power on key for 1 second, and the
power on is completed after the full display self check.
• Confirm that the measurement mode above the screen is body temperature
mode (non object temperature mode)
• Align the forehead temperature gun probe with the middle of the forehead
and keep it vertical, with a distance of about 3-5cm. Press the measurement
key to start the measurement. After about 1 second, the screen displays the
measurement value. Press the measurement key for 5 seconds to shut down
when no measurement is made, or shut down automatically after 30
seconds.
When 34o C ≤T ≤37,3 o C, bright green backlight.
When 37,4o C ≤T ≤38o C, bright yellow backlight.
When 38,1o C ≤T ≤42,9o C, bright red backlight.
When T < 34o C,bright green backlight, display "LO"."
When T > 42,9o C, bright red backlight, display "HI"."
Warm Tips:
1. Before and after use, please keep the sensor and probe cavity clean.
2. Please place the forehead temperature gun in a temperature stable
environment for use. When ambient temperature changes greatly (e.g. from
indoor to outdoor).
3. Do not begin to measure body temperature immediately after measuring
the temperature of an object at very high or very low temperature. Please
place it for ten minutes.
4. When the measurement object comes from a place that is quite different
Setting up guidance
This product provides three function settings: measurement mode, tone
switch, temperature unit, etc.The comparison table of setting menu is as
follows:
• Shortcut switch mode: in the boot state,
short press "SET" key can realize the quick
switch of human temperature and object
temperature.
• In the power on state, press and hold "set"
for 2 seconds, and F1 will be displayed on the
screen, then press the "+" or "-" button to
switch between "body temperature
measurement" / "object temperature
measurement".
Function Key Description
Icon
definition
Electricity
indication
Tone
Temperature
measurement
mode
Display Unit
Display value
Memory
symbol
Icon State description
Display
Display and
flashing
No display
Display
No display
Body temperature measuring mold.
Object Surface temperature measuring mold.
Celsius temperature.
Fahrenheit temperature.
It will show the measured temperatur
information.
Display value is memory value and group
number.
The battery power is low
and can only work for a
short time. Please replace
the battery.
The battery is too low to
work properly. Please
replace the battery
immediately
Full charged
Buzzer sound on, with
prompt sound
Buzzer sound off, no prompt
sound
Function key
SET
+
-
Function description
Enter / Exit the menu and switch the setup items
Select the confirmation item to look up the measured value
Select the confirmation item to look down the measured value
Menu
F1
F2
F3
Function
Te s t
mode
Test mode
Temperature
unit
“SET”Key
Press once
Press again
Press again
“+” Key
Object
Temperature
Model
Tips
oC
“-” Key
Human
Temperature
Model
No hint
oF
With prompt
sound
Human
Temperature
Model
Tips
oC
oC
oF
M
oC
M
oC
M M
oC
M
oC
M
oC
M
oF
M
oC
LCD Dispaly Function
setting key
Body temperature setting / Object temperature
• In the power on state, press and hold "set"
for 2 seconds, and the screen displays
F1,Press the "set" key 1 time it will show
F2.then press the "+" or "-" key to switch
between prompt tone on and prompt tone
off.
Temperature unit conversion settings
• In the power on state, press and hold "set"
for 2 seconds, and the screen displays
F1,Press "set" key 2 times, it will show F3,
then press the "+" or "-" key to switch
between °C and °F
Setting of tone switch from the measured ambient temperature, it should stay in the test environ-
ment for at least five minutes.
5. Try not to measure in the forehead blowing, drenching water, sweating,
coating, smear cosmetics, etc. Do not take body temperature within 30
minutes after exercise, bath, meal.
When the forehead temperature gun is out of working temperature, the
screen will prompt: after the boot complete self-test, the screen will show
the ambient temperature. When the working environment temperature is
lower than 0oCthe screen will display “Err 1”, backlight red, when the ambient
temperature is higher than 42oC, the screen will display “Err 2”, backlight red.
Object temperature measurement
• Select object temperature mode.
• Aim the thermometer probe at the measuring target and keep it vertical,
the distance is about 3-5 cm press the measuring key, display the temperatu-
re after about 1 second, when not measuring often press the measuring key
for 5 seconds to shut down, or turn off automatically after 30 seconds.
Warm Tips:
1. The range of measurement of the temperature measurement mode of the
object 0oC - 100oC
2. This function measures the object surface temperature and does not
represent the object core temperature.
3. The emissivity of different materials may be different (refer to the
emissivity of materials), and the measured temperature will deviate slightly
from the actual temperature.
4. When the measured value is less than 0oC, bright red backlight, display
"LO".. 5.When the measurement is higher than 100oC, bright red backlight,
display "HI".
Product maintenance and maintenance methods
Because the product is a reusable device, please pay attention to the
cleaning process after use.
Please keep the inner cavity of sensor and probe clean, otherwise it will
affect the measurement accuracy. Surface cleaning: wipe dirt with clean soft
cloth or cotton stick with a little medical spray.
Clean the inner cavity of the sensor and probe: gently wipe the inner cavity
of the head or the top of the sensor with a clean soft cloth or cotton stick
with a little medical sprinkler. When the alcohol is completely volatile.
Storage conditions, methods
Products must be kept clean and kept in a dry place. Don't put the electronic
forehead temperature gun in a place with electric shock. do not store the
electronic forehead temperature gun in an extreme temperature environment
above 55oCor below -10oCand humidity above 85%.
C
M
Y
CM
MY
CY
CMY
K
Dors manual 1081 (angles).pdf 1 18/6/20 12:12
