Generac Power Systems MPSG350 User manual

Standby Power Rating Prime Power Rating
350 KW 60 Hz 280 KW 60 Hz
nThe Generac Modular Paralleling system utilizes
multiple small generators in a side by side parallel
arrangement to achieve a larger combined power
output.
nThe proven 13.3 liter Generac generators can be
combined up to 10 units to provide from 300 kW to 1
megawatts of reliable power.
nParalleling System Features. The paralleling function is
controlled by Generac’s field proven Power Manager
Control utilizing contractor switching technology
resulting in cost effective reliable paralleling. The MPS
control system provides automatic synchronization,
adjustable load sharing between generators, reverse
power protection and load shedding contacts.
nThe optional cable interconnect cabinet is furnished with
bus bar and lugs to allow easy cabling between the
multiple gensets. Recommended for 3 or moregensets.
nThe Generac “Power Manger Generator controller”
provides complete engine monitoring and control along
with alarm function and communication ability via a
RS232with a modem link toGenerac’s Genlink
software or Modbus control. A RS485 link is also
available.
nFlexibility. The Modular Power systems flexibility allows
for a wide variety of configurations, including single or
multiple automatic transfer switch arrangements roof
application where better weight distribution is required
and areas with specific height or depth limitations.
Since MPS gensets need not be located together, space
can be utilized wherever it is available. Smaller units
are also easier to transport and place on thejobsite.
nRedundancy. N+1 means greater reliability withMPS.
Backuppower duringscheduled maintenance.
Simplifiedservice which reduces maintenance costs.
nSingle source service response fromGenerac’s dealer
network provides parts and service support for the entire
unit. You are never on your own when you own a
Generac Power System
GEN
DieselGenerator
Circuit
Breaker
Contactor Contactor
Diesel Generator
Circuit
Breaker
GEN
Transfer Sw
W/ Integral
Control
UTILITY
Distribution
Cab
Contactor
DieselGenerator
Contactor
Circuit
Breaker Circuit
Breaker
DieselGenerator
GEN GEN
UTILITY
ATS
UTILITY
ATS
Distribution
Cab
Distribution
Cab
PMSC
Controller
Cabinet
Control Wires
Power Manager Integrated Controller
Layout
Power Manager System Controller Layout
FEATURES
Modular Power
System (MPS)
Powered with Generac’s 13.3 Natural Gas Engine
MPSG350
350 kW
®

Modular Paralleling System
MPSG 350
System Description
The Generac control system consists of the Power Manager™
System Controller (PM-SC) or the Power Manager Integrated
Controller ()PM-IC) along with the Power Manager Generator
Controller (PM-GC). For single transfer switch installations with
the Generac Transfer Switch, the PM-IC is integral with the
transfer switch. For multiple transfer switch installations, the
PM-SC interfaces with the PM-GC to provide start/stop
commands based on utility power, proportional load sharing
and safe paralleling of each individual genset to the main bus or
transfer switch. Each individual genset has a built in heavy duty
switch to complete the paralleling operation. This switch and
it's control system replace the high cost switchgear and motor
operated circuit breakers associated with standard paralleling
systems.
System Components
Power Manager Generator Controller (PM-GC)
This control is installed on the generator set and monitors
all the engine parameters, including oil pressure, coolant
temperature, overspeed, kW and power factor.
It also controls the governor, voltage regulator and
the synchronizing connection to the bus.
Paralleling Switch
Installed in the generator set connection box
Heavy duty 3 pole solenoid actuated, mechanically
held, with emergency trip to off position
Rated at 400 amps and 1000 amps continuous
35,000 and 42,000 amps interrupting capacity
Built in arc suppression
Power Manager System Control (PM-SC)
Up to 3 primary transfer switches with up to 6 individual
steps for load sequencing, application or shedding with
assignable kW values for each step in addition to the
critical loadATS.
Unlimited number of secondary slave switches
The PM-SC is in an enclosure separate from the transfer
switches.
Power Manager Integrated Control (PM-IC)
Integrated Control (IC) is installed in the same enclosure
as the single Generac Transfer Switch
Features:PM-IC & PM-SC
Programmable and viewable via Genlink
Provides up to 3 load shed contacts
Failsafeprotective functions for reverse
power and synchronous paralleling control.
`` Exercisecontroller
Backup battery
RS232 for Modem connection
RS485 Data Highway
Transfer Switch (PM- IC System )
1000 amp,1600 amp, 2600 amp (UL)3200 Amp (non UL)
For smaller switch ratings use the PM-SC control
42,000 AIC – 1000 Amp, 65,000 AIC – 1600 Amp,
85,000 AIC – 2600 - 3200 Amp
NEMA 12/3R enclosure
66"H x 36"W x 30" D – 1000 Amp
78"H x 48"W x 24" D – 1600 Amp
80” H x 48” W x 48” D – 2600 –3200 Amp
Wire access – top, side, bottom
NEMA 3R or 4X Optional
Wt. 1250 lbs. –1000-1600 Amp. 1850 lbs. 2600-3200 Amp
Connection Cabinet ( Optional )
NEMA 12/3R
80” H x 48” W x 48” D
Lug capacity –16 for Generator Controller (GC), 12 for
ATS. Each lug accepts (4) #4 to 750 MCM ( see Dwg. OD4482)
Floor mounting
Aluminum or Copper Wire compatible – 4500 amp bus
Sequence of Operations
1. The PM-IC or a transfer switch in the PM-SC configuration
detects a Utility failure and issues a start command. In the
PM-IC, the command goes direct to each PM-GC and with
multiple transfer switches the command goes to the PM-SC
which then issues a start command to the PM-GC's
2. Each Generator will start on its own.
3. The first generator that attains rated frequency and voltage
is connected to the main bus or transfer switch terminals via
the paralleling switch n the individual genset.
4. The remaining generators will synchronize with the bus and
the respective paralleling switch will close into the bus.
5. When all the gensets are paralleled to the main bus, the
System or Integrated Controller will signal the transfer switch
to transfer to the load. If multiple transfer switches are
installed, the PM-SC will connect these switches in 3
separate programmed steps.
6. If a NFPA requirement for 10 second start exists, the first
unit connects to the bus. This causes the controller in a
separate emergency transfer switch to immediately transfer
to the NFPA load.
7. If a single generator fails, load shed contacts are available to
disconnect selected non critical loads.
8. If load conditions are reduced, (night time operation)
selected generators can be programmed off line.
9. When Utility supply returns, the PM-SC or PM-IC will issue
commands to transfer loads back to the Utility. If then issues
commands to the individual PM-GC’s to disconnect from the
bus. Each PM-GC will operate its generator for the cool-
down period and then issue a shutdown command.
System Configuration
Any KW configuration that equals the required load kW
can be used. The following page details a common
engine configuration and the most economical
configuration utilizing the MG150, MG200. But,
depending on load parameters any number of units up to
10 can be paralleled together.
Additional units and transfer switches can easily be added
at a later date.
APPLICATION
& ENGINEERING DATA MPSG 350
Ratings definitions
: See Generac Power Systems "
Power Rating Guidelines
" for specific definitions and application guidelines of the Standby Power, Prime Power and Continuous Power
Ratings. Prime Power is not available at this time forMPS units.

350 kW 437.5 kVA
15%
20%
25%
30%
35%
% of Rated Load 1,209
2,329
3,429
4,467
Heat Rejection to Coolant( Full Load )
Coolant Capacity (total)
Max air temp to radiator º F (derates apply)
Max ambient temperature º F (derates apply)
Flow at Rated Power ( cfm)
0.5 inches H2O
Combinations
581
711
784
Inst Dip
kVA
958
0.16
0.23
kW Cu Ft / Hr Therms/Hr.
208 Volts 1.0 PF 480 Volts 1.0 PF
90.40% 90.70%
3.50%
34,400 for the 3 units 17,200 for each unit
175
Natural Gas 950 BTU /Cu.Ft
87.5 11.49
262.5
350
22.12
32.58
1,206,000 BTU/Hr. Total for the 2 units 1@ 700,000 btu/hr 1@ 506,000btu/Hr.
42.44
90.50%
15.4 gallons for the 2 units 77 Gallons per unit
0.18
3.1
CBA
0.5%
0.07
0.0078
80% Load
100%
90.70% 91.10%
90.90%
Engine Fuel Consumption @
350 kW
MPSG350
415 637
804
208 Volt Parallel Wye Network 480 Volt Series Wye Network
Rated Amps
1214
459
1098890
120/208
Motor Starting
277/480
600 421
1 - 200 kW, 1 - 150 kW
TOTAL SYSTEM PARAMETERS
50%
Neg Sequence Reactance
Time Constant Seconds
Max Harmonics
Efficiency % @
Output Voltage 60 Hz.
Alternator Parameters
Sub Transient Reactance
526
Transient Reactance
Synchronous Reactance
Alternator Models
75%
25%
60% Load
1128
Exhaust Flow @ FL
120 º F
Exhaust 1174 cfm Total. 618 cfm + 556 cfm
4017 CFM for the 2 units 2257 CFM + 1760 CFM
Engine Cooling
2.0% for every 1000 ft above
Altitude 0.7% for every 100 m above
Exhaust Temperature ( Average)
Exhaust Outlet per engine
Power Adjustments
Temperature 2% for every 10 º C above
1.0% for every 10 º F above
Maximum External Press Drop on Rad
1 @ 4.0" NPT
140 º F
Inlet Cooling Air CFM
Combustion Air Requirements
100% Load
Zero Sequence Reactance
Voltage Balance
Phase Sequence
1-200 kW plus 1 - 150 kW 520 mm PMG Generac Alternators
* Note: Temperatures will require necessary derates be applied. Unless otherwise noted, all data at 480 volt wye - 1.0 PF.
3500 Feet
350 kW Standby
40 º C
104 º F
1066 Meters

INTERCONNECTION DIAGRAM
PMIC Power Manager Integrated Control PMSC Power Manager System Control
DISTRIBUTED BY:
GENERAC POWER SYSTEMS, INC.MPSG350
The PM-SC can control 3 transfer switches and any number of
slave switches. The main connection box would be configured for
the size and number of wires for the specific application.
1 - 200 kW 13.3 Liter
+ 1 - 150 kW 13.3 Liter Gas
Powered Generator
Modules
The PM-IC is part of the
Generac Transfer Switch
A connection box for the power wires is an option.
GENERAC POWER SYSTEMS,INC.
P.O.BOX 8 WAUKESHA, WI. 53187
262-544-4811 FAX [phone]
©
2003 GENERAC POWER SYSTEMS, INC. All rights reserved. All specifications subject to change without notice. Bulletin # 0168230SBY MW 06-28-03
Typical Installations
Area Space Requirements.
Units can be placed end to end, side by side or wherever room is available. The transfer switch or switches are generally placed
close to the main electric service. Consult State, Federal and Local codes for specific installation requirements.
Power Connections are in one area in the left rear quadrant of the genset.
All controls are through a single 2 wire RS485 connection that can be daisy chained between generators.
Generator Generator
ATS ATSATS
Power
Manager
System
Control
(PM-SC)
Control Wiring
Power Wiring
Gen Bus or
Connection
Cabinet (Opt)
Generator Generator
Power Manager
Integrated
Control
Transfer
Switch
control
powerpower
control
Standard Enclosed units shown.
Sound attenuated package adds an
additional 26" to the length.
Units can also be non-enclosed for
indoor installations.
AIR AND
EXHAUST
OUTLET
TOPSIDE
TOP VIEW
13.3 LITER
AIR AND
EXHAUST
OUTLET
TOPSIDE
TOP VIEW
13.3 LITER
Minimum Clearance
between units
Electrical
Connections
this area
Electrical
Connections
this area