Generac Power Systems PWRcelP XVT076A03 Installation instructions

SAVE THIS MANUAL FOR FUTURE REFERENCE
Register your Generac product at:
WWW.GENERAC.COM
1-888-GENERAC
(1-888-436-3722)
Register your Generac product at:
https://pwrfleet.generac.com
1-888-GENERAC
(888-436-3722)
Para español, visita: http://www.generac.com/service-support/product-support-lookup
Pour le français, visiter: http://www.generac.com/service-support/product-support-lookup
Installation and Owner’s Manual
Generac PWRcell® Inverters
XVT076A03
009954
(000209b)
WARNING
Loss of life. This product is not intended to
be used in a critical life support application.
Failure to adhere to this warning could result
in death or serious injury.

ii Installation and Owner’s Manual for Generac PWRcell Inverter
Use this page to record important information about your Generac Product
Record the information found on your unit data label on this page. See .
When contacting an Independent Authorized Service Dealer (IASD) or Generac Customer Service, always supply the complete
model number and serial number of the unit.
Table 1: PWRcell Inverter Important Information
Unit Model Number
Unit Serial Number
Date Purchased
Commissioning Date
(000393a)
WARNING
CANCER AND REPRODUCTIVE HARM
www.P65Warnings.ca.gov.

Installation Manual for Generac PWRmanager 12 Relay Load Controller iii
Table of Contents
Section 1: Safety Rules & General Informa-
tion
Introduction ..........................................................1
Read This Manual Thoroughly ....................................1
Safety Rules .........................................................1
How to Obtain Service .................................................1
General Hazards ..................................................2
PVRSE Warning ..........................................................2
PVHCE/PVHCS Warning ............................................3
Electrical Hazards ................................................3
Section 2: General Information
Specifications ......................................................5
Serial Number Location ......................................6
Unit Dimensions ..................................................6
Component Locations .........................................6
About PWRcell Inverters .....................................6
Inverter Control Panel .........................................7
REbus Status LED ......................................................7
Inverter Status LED .....................................................7
Internet Status LED .....................................................7
Shutdown Mode ...................................................8
Section 3: Location and Standards
Location ................................................................9
Standards .............................................................9
Immunity ......................................................................9
Photovoltaic Rapid Shutdown ..........................10
PVRSS Initiation ........................................................10
PVRSS Self-Test .......................................................11
Photovoltaic Hazard Control ......................................11
Voltage and Frequency Trip Settings ..............12
Voltage Trip ...............................................................12
Frequency Trip ..........................................................12
Section 4: Installing PWRcell Inverter
Mounting Clearances ........................................13
Mounting Bracket Dimensions .........................13
Mounting the Inverter ........................................14
Section 5: Electrical Connections
Accessing Wiring Compartment ...................... 15
PWRcell Inverter Wiring Compartment ........... 15
Wiring Guidelines .............................................. 17
Grounding Bar Wiring ....................................... 17
DC Wiring ........................................................... 18
STOP Terminal Wiring ...................................... 18
For PV only installations without a PWRcell Battery: 18
For Installations with a PWRcell Battery: ..................18
AC Wiring ........................................................... 19
Partial Home Backup ........................................ 20
Managed Whole Home Backup ........................ 22
AC Generator Integration ................................. 24
PWRcell ATS Controller Upgrade Kit ........................25
Connecting Ethernet ......................................... 25
Configuring Static IP Settings ....................................25
Verifying Connectivity ................................................26
Current Transformers (CTs) ............................. 27
Locating Current Transformers .................................27
Connecting CTs to the Inverter .................................28
Connecting Multiple Sets of CTs ...............................28
Connecting CTs to Multiple PWRcell Systems /
Inverters ....................................................................28
CT Calibration ...........................................................29
Other Equipment ............................................... 31
PWRcell ATS .............................................................31
Load Management Options .......................................31
Section 6: Commissioning
Before You Start: ............................................... 33
Commissioning Overview ................................ 33
Commissioning Steps ....................................... 33
Turn on AC Power to Inverter ....................................33
Check AC Voltages ...................................................33
Verify Internet Connection .........................................34
Register System ........................................................34
Select Inverter System Mode ....................................34
Configure Inverter Settings and Enable Inverter .......35
Configure Rebus Devices and Enable REbus
Devices .....................................................................39
Test Island Mode .......................................................39

iv Installation Manual for Generac PWRmanager 12 Relay Load Controller
Advanced Commissioning Steps .....................39
Configure Time of Use .............................................. 39
Access Installer Configuration Tool .......................... 43
Set Inverter Grid Compliance .................................... 44
Set Import / Export Compliance ................................ 45
Commissioning Multiple Inverter Systems .....47
Multiple Inverter System Pre-Commissioning
Checklist ................................................................... 47
Multiple Inverter System Commissioning Procedure 47
How to identify PLM Crosstalk .................................. 48
PLM Crosstalk Recovery Procedure ......................... 48
Section 7: System Operation
General Information ...........................................49
Operation and User Interface ...........................49
Home Screen ......................................................49
Home Screen Icons ...........................................49
Activating the System Post Permission to Oper-
ate (PTO) .............................................................50
Activating Post PTO: System Operating ................... 50
Activating Post PTO: System Disabled ..................... 50
Confirm Inverter Settings .......................................... 52
PV Only System ........................................................ 52
PV + Battery w / a Protected Loads Subpanel for Partial
Home Backup ........................................................... 52
PV + Battery w / a PWRcell ATS and Load Management
for Managed Whole Home Backup ........................... 53
System Modes Overview ...................................54
Grid Tie ..................................................................... 54
Self Supply ................................................................ 54
Clean Backup ............................................................ 55
Priority Backup .......................................................... 55
Remote Arbitrage ...................................................... 56
Sell ............................................................................ 56
Island Mode ........................................................56
AC Generator Control Modes ...........................57
AC Generator Manual Override ........................57
To perform an AC Generator Manual Override ......... 57
Automatic Generator Override Conditions ................ 58
Section 8: Maintenance
Service ................................................................ 59
Accessing Wiring Compartment ...................... 59
Replacing Fuses ................................................ 59
Annual Maintenance ......................................... 60
Inspecting Vents ....................................................... 60
Cleaning Intake Filter ................................................ 60
Section 9: Troubleshooting
General Troubleshooting .................................. 61
Overload Behavior ............................................ 62
Section 10: Appendix A
Grid Support Functions: Parameter Values and
Range of Adjustability ...................................... 67

Safety Rules & General Information
Installation and Owner’s Manual for Generac PWRCell Inverter 1
Section 1: Safety Rules & General Information
Introduction
Thank you for purchasing a Generac PWRcell® product.
The Generac PWRcell Inverter is a storage-ready
inverter that connects to the PV Link™ optimizers and
PWRcell Batteries to form the Generac PWRcell system.
This manual provides instructions for installing the
PWRcell Inverter, including mounting, wiring, and battery
integration information.
The information in this manual is accurate based on
products produced at the time of publication. The
manufacturer reserves the right to make technical
updates, corrections, and product revisions at any time
without notice.
Read This Manual Thoroughly
If any section of this manual is not understood, contact
the nearest Independent Authorized Service Dealer
(IASD) or Generac Customer Service at 1-888-436-3722
(1-888-GENERAC), or visit www.generac.com for assis-
tance. The owner is responsible for correct maintenance
and safe use of the unit.
This manual must be used in conjunction with all other
supporting product documentation supplied with the
product.
SAVE THESE INSTRUCTIONS for future reference. This
manual contains important instructions that must be fol-
lowed during placement, operation, and maintenance of
the unit and its components. Always supply this manual
to any individual that will use this unit, and instruct them
on how to correctly start, operate, and stop the unit in
case of emergency.
Installation and commissioning of a PWRcell system
should be performed after obtaining the necessary
approvals and permitting from local authorities and utility.
Safety Rules
The manufacturer cannot anticipate every possible
circumstance that might involve a hazard. The alerts in
this manual, and on tags and decals affixed to the unit,
are not all inclusive. If using a procedure, work method,
or operating technique that the manufacturer does not
specifically recommend, verify that it is safe for others
and does not render the equipment unsafe.
Throughout this publication, and on tags and decals
affixed to the unit, DANGER, WARNING, CAUTION, and
NOTE blocks are used to alert personnel to special
instructions about a particular operation that may be
hazardous if performed incorrectly or carelessly. Observe
them carefully. Alert definitions are as follows:
NOTE: Notes contain additional information important to
a procedure and will be found within the regular text of
this manual.
These safety alerts cannot eliminate the hazards that
they indicate. Common sense and strict compliance with
the special instructions while performing the action or
service are essential to preventing accidents.
How to Obtain Service
For assistance, contact the nearest Independent Autho-
rized Service Dealer (IASD) or Generac Customer Ser-
vice at 1-888-436-3722 (1-888-GENERAC), or visit
www.generac.com.
When contacting an IASD or Generac Customer Service,
always supply the complete model and serial number of
the unit as given on its data decal located on the unit.
Record the model and serial numbers in the spaces pro-
vided on the front cover of this manual.
(000100a)
Consult Manual. Read and understand manual
completely before using product. Failure to
completely understand manual and product
could result in death or serious injury.
WARNING
(000001)
DANGER
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
(000002)
WARNING
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
(000003)
CAUTION
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.

Safety Rules & General Information
2 Installation and Owner’s Manual for Generac PWRCell Inverter
General Hazards
•PWRcell system is required to be connected to a
120/240 VAC 1-Phase (Wye) utility grid. Connect-
ing the PWRcell Inverter to the electric utility grid
must only be done after receiving prior approval
from the utility company.
•Generac does not currently support autonomous,
off grid installations with PWRcell equipment. If this
installation is in Canada, the installation shall be in
accordance with the Canadian Electrical Code,
Part I.
•Only competent, qualified personnel should install,
operate, and service this equipment. Strictly com-
ply to local, state, and national electrical and build-
ing codes. When using this equipment, comply with
regulations established by the National Electrical
Code (NEC), CSA Standard, and the Occupational
Safety and Health Administration (OSHA), or the
local agency for workplace health and safety.
•Protection against lightning surges in accordance
with local electric codes is the responsibility of the
installer.
NOTE: Lightning damage is not covered by warranty.
•Never work on this equipment while physically or
mentally fatigued.
•Any voltage measurements should be performed
with a meter that meets UL3111 safety standards,
and meets or exceeds overvoltage class CAT III.
PVRSE Warning
This photovoltaic rapid shutdown equipment (PVRSE)
does not perform all of the functions of a complete photo-
voltaic rapid shutdown system (PVRSS). This PVRSE
must be installed with other equipment to form a com-
plete PVRSS that meets the requirements of NEC (NFPA
70) section 690.12 for controlled conductors outside the
array. Other equipment installed in or on this photovoltaic
(PV) system may adversely affect the operation of the
PVRSS. It is the responsibility of the installer to ensure
that the completed PV system meets the rapid shutdown
functional requirements. This equipment must be
installed according to the manufacturer’s installation
instructions.
Follow all instructions included in this manual and use
appropriate practices for all product wiring and
installation.
(000188)
DANGER
Electrocution. Do not wear jewelry while
working on this equipment. Doing so will
result in death or serious injury.
(000191)
DANGER
Automatic start-up. Disconnect utility power and
render unit inoperable before working on unit.
Failure to do so will result in death or serious injury.
(000187)
WARNING
Electrocution. Potentially lethal voltages are generated
by this equipment. Render the equipment safe before
attempting repairs or maintenance. Failure to do so
could result in death or serious injury.
Risk of injury. Do not operate or service this machine
if not fully alert. Fatigue can impair the ability to
operate or service this equipment and could result in
death or serious injury.
(000215a)
WARNING
(000209b)
WARNING
Loss of life. This product is not intended to
be used in a critical life support application.
Failure to adhere to this warning could result
in death or serious injury.
(000640)
WARNING
Equipment damage. Connecting inverter to electric utility
grid must only be done after receiving prior approval
from utility company. Failure to do so could result in
equipment or property damage.
(000155a)
WARNING
Electric shock. Only a trained and licensed electrician
should perform wiring and connections to unit. Failure to
follow proper installation requirements could result in death,
serious injury, and equipment or property damage.
(000182a)
WARNING
Equipment damage. Only qualified service personnel may
install, operate, and maintain this equipment. Failure to
follow proper installation requirements could result in death,
serious injury, and equipment or property damage.
Equipment damage. Connect only to REbus-compatible
devices to the DC bus. Never connect to any other DC
power source. Connecting to other DC power sources
could result in equipment damage. (000598a)
CAUTION

Safety Rules & General Information
Installation and Owner’s Manual for Generac PWRCell Inverter 3
PVHCE/PVHCS Warning
The XVT076A03 inverter may be installed as part of a
PVHCS to meet the requirements of NEC 690.12.
Replacing any equipment connected to this system may
compromise the PVHCS. Only PVHCE certified PV Links
may be used to replace PV Links installed in a PVHCS.
Only PVHCE certified PWRceIl Inverters may replace
inverters installed in a PVHCS. The replacement of any
other system component noted in the PWRcell PVHCS
Instructions must carry the same or better ratings and
certifications.
Electrical Hazards
(000104)
DANGER
Electrocution. Water contact with a power
source, if not avoided, will result in death
or serious injury.
(000604)
Electrocution. PWRcell Battery front cover should
be removed by a qualified technician only.
Removing the front cover could result in death,
serious injury, equipment or property damage.
DANGER
(000145)
DANGER
Electrocution. In the event of electrical accident,
immediately shut power OFF. Use non-conductive
implements to free victim from live conductor. Apply
first aid and get medical help. Failure to do so will
result in death or serious injury.
(000599)
Electrocution. Turn battery disconnect OFF and
de-energize REbus before touching terminals.
Failure to do so will result in death, serious injury,
equipment and property damage.
DANGER
(000152)
DANGER
Electrocution. Verify electrical system is
properly grounded before applying power.
Failure to do so will result in death or serious
injury.

Safety Rules & General Information
4 Installation and Owner’s Manual for Generac PWRCell Inverter
This page intentionally left blank.

Installation and Owner’s Manual for Generac PWRcell Inverter 5
General Information
Section 2: General Information
Specifications
Description Units XVT076A03
Max. cont. grid-tied AC power @ 122°F (50ºC) kW 7.6
Max. cont. AC power in island mode w/ external transfer switch and
single 6 module battery cabinet2kW 9.0
Max. cont. AC power in island mode w/ external transfer switch and 2 battery cabinets (8 mod-
ules minimum)1kW 11.0
Peak motor starting current (2 sec) A rms 50
Normal output frequency AC Hz 60
Grid Voltage Line to Neutral (L-N) VAC 120
Grid Voltage Line to Line (L-L) VAC 240
Peak efficiency % 97.3
Optimal split phase imbalance for max. system performance % ≤ 30
CEC weighted efficiency % 96.5
AC terminals wire size AWG 8 to 6
DC terminals wire size AWG 10 to 6
STOP terminals wire size AWG 20 to 14
Normal Operating Performance Category - Category B
Abnormal Operating Performance Category - Category III
Weight lb (kg) 70.9 (32.1)
Thermal management – forced convection
Weatherization rating – NEMA Type 3R
Enclosure Material – powder-coated steel
Description Units Min Nominal Max
REbus voltage V dc 360 380 420
REbus current A dc 30†
REbus input short circuit current2A dc 30
Max input circuit backfeed current (fault condition) A dc 0
Output power factor rating AC (25%, 50%, 100% of rated power) - 0.96 0.98 0.99
Operating voltage range AC, XVT076A03 / (L-N) V rms 106 120 132
Operating voltage range AC, XVT076A03 / (L-L) V rms 2124240 264
Continuous output current AC grid-tied A rms 32
Output controlled current AC grid-tied A rms 0 32
Continuous output current AC islanded A rms 45
Synchronization Inrush Current A rms/p-p 32.1 / 94.83
Output fault current duration A / ms 50 / 2,000
Protected Loads output overcurrent protection A 50
Full Power operating ambient temperature range3 °F (°C) -4 (-20) +122 (+50)
Trip voltage and frequency limits See Voltage and Frequency Trip Settings
Measurement and Calculation Accuracy See Table 2-1.
1 Peak performance, values provided for 104º F (40º C)
2 Rating for one DC input. Four total.
3 Includes ambient temperature rising from inverter operation.
4 Minimum voltage before disconnection is subject to UL 1741-SB low voltage ride-through and regional configurations requirements. Per require-
ments, the inverter shall perform required low voltage ride-through operation for one second. If required as specified by an Electric Utility, the
inverter may continue in operation past one second so long as the line-to-line voltage is greater than 40 Vrms
†Inverter limits its REbus current to adhere to its AC power rating. Total REbus current capability from multiple REbus sources may safely
exceed this value as the inverter safely limits the amount utilized.

6 Installation and Owner’s Manual for Generac PWRcell Inverter
General Information
Serial Number Location
Refer to Figure 2-2 to locate unit serial number (D).
Record the information from the product nameplate in
Table 1: PWRcell Inverter Important Information on
the inside front cover of this manual.
Unit Dimensions
Figure 2-1. Unit Dimension
Component Locations
Figure 2-2. Component Locations
About PWRcell Inverters
The PWRcell Inverter connects PV Link™ optimizers and PWRcell Batteries to form the PWRcell system for grid-inter-
active solar-plus-storage. Upon the loss of utility grid power, the PWRcell Inverter disconnects from the grid and pro-
vides AC power to support protected loads when configured to do so with PWRcell ATS. This capability is referred to as
Island Mode. For more information, see Island Mode in Section 7:System Operation.
PWRcell Inverter uses the REbus™ 380 VDC nanogrid to connect DC-coupled PWRcell devices. The REbus nanogrid
automates and regulates the flow of power to enable plug-and-play setup and operation of PWRcell equipment. For
more information about REbus, visit www.generac.com. In Figure 2-3, the PWRcell Inverter (E) is directly connected
to PV Link optimizers (B) and PWRcell Battery (C) on DC (REbus) lines (D). To the right of the inverter are AC lines for
the Grid (F), home loads (G), PWRcell ATS (H), and backup loads (J).
Table 2-1. Measurement and Calculation Accuracya
Steady-state measurements Transient measurements
Parameter Measurement
Accuracy
Measurement
Window Range Measurement Accuracy
Measurement
Window Range
Voltage, RMS ± 1.2 V (1%) 10 cycles 60 V - 144 V ± 2.4 V (2%) 5 cycles 60 V - 144 V
Frequencyb10 mHz 60 cycles 50 Hz - 66 Hz 100 mHz 5 cycles 50 Hz - 66 Hz
Active Power ± 380 W (5%) 10 cycles 1,520 W - 7,600 W Not required N/A N/A
Reactive Power ± 285 var (5%) 10 cycles 1,140 - 5,700 var Not required N/A N/A
Time 1% of measured
duration N/A 5 s to 600 s 2 cycles N/A 100 ms < 5 s
aFor voltage THD < 2.5% and individual voltage harmonics < 1.5%
bFor when the fundamental voltage is greater than 30% of the nominal voltage
A24-3/4 in (628 mm)
B19-3/8 in (491 mm)
C8-3/8 in (214 mm)
B
A
C
009955
AControl Panel
BIntake Filter
CExhaust Vent
DNameplate
009654
A
B
C
D

Installation and Owner’s Manual for Generac PWRcell Inverter 7
General Information
.
Figure 2-3. Generac PWRcell System Example
Inverter Control Panel
Figure 2-4. Inverter Control Panel
See Figure 2-4. The PWRcell system is controlled
through the PWRcell Inverter control panel. The inverter
control panel is used for adjusting system settings and for
interacting with devices.
REbus Status LED
REbus Status LED (C) communicates REbus nanogrid
status through LED color.
Inverter Status LED
Inverter LED (D) communicates the status of the utility
grid and / or inverter through LED color and state.
Internet Status LED
Internet LED (G) is illuminated when the inverter has a
connection to the Generac server. Internet LED (G) will
slowly strobe when REbus Beacon is updating its
firmware.
ASolar Panels DREbus GATS
BPV Link EPWRcell Inverter HLoads
CPWRcell Battery FGrid JBackup Loads
015164
A
C
D
EFG
H
B
B
B
DJ
ALCD Display EShutdown Button
BNavigation Keys FShutdown LED
CREbus Status LED GInternet LED
DInverter LED HSelect
LED Color REbus Status
Green All devices are enabled and functioning
normally on REbus.
Yellow One or more devices are disabled, or no
devices are detected.
Red A serious fault has been detected on a
device or the REbus wiring.
REbus Inverter
Internet
Shutdown
(hold)
A
D
C
B
G
E
F
H
009894
LED Color Inverter Status
Green Utility is connected and within normal
operational voltage and frequency.
Green Blinking
Inverter is in Island Mode due to a utility
service interruption. Utility is not within
normal operational voltage and frequency.
Yellow Inverter is disabled or powering up.
Yellow Blinking
Inverter is waiting to connect to the grid, in
the process of connecting to REbus, or
waiting to connect to REbus.
Red
Inverter is overloaded, or a serious fault
has been detected on the inverter. Manual
intervention is likely required before the
equipment will resume operation.
No Light Inverter is powered down.
LED Color Internet Status
Blue Internet connected
Blue Strobing
Internet connected and Beacon firmware
auto-update is in progress.
Note: Do not power off the inverter or
unplug REbus Beacon while update is in
progress.
No Light Not internet connected.

8 Installation and Owner’s Manual for Generac PWRcell Inverter
General Information
Shutdown Mode
NOTE: A loss of grid power will not de-energize REbus
in a PWRcell system configured to enter Island Mode
with enabled energy storage.
Shutdown button (E) activates a transition to shutdown
mode.
Disabled PWRcell equipment limits output voltages to a
safe level for servicing.
After pressing the Shutdown button and entering
Shutdown Mode, the AC section of the inverter will still be
powered, unless there is an active utility service
interruption, or the AC solar backfeed breaker, AC solar
disconnect, building AC disconnect, or main service
breaker is shut off.
To enter shutdown, press and hold shutdown button (E).
In shutdown mode:
•The PWRcell Inverter will stop sourcing power to
REbus, and immediately disable all communicating
power sources on REbus by sending a system-
wide system mode change signal.
NOTE: Successful signal transmission relies upon
proper configuration of PLM channels across REbus
devices (PV Links and Batteries).
•Shutdown LED (F) will illuminate.
•Inverter screen (A) will display REbus DC bus volt-
age and text indicting Shutdown mode has been
initiated.
To exit shutdown, follow the prompts provided on the
LCD screen.
(000600)
DANGER
Electrocution. Initiate a system-wide shutdown and turn the
PWRcell DC Disconnect Switch OFF on all connected
batteries before performing service. Failure to do so will
result in death, serious injury, or equipment and property
damage.

Location and Standards
Installation and Owner’s Manual for Generac PWRcell Inverter 9
Section 3: Location and Standards
Location
When installing the PWRcell Inverter, consider the follow-
ing:
•The inverter installation location must meet the
working space requirements in NEC Article 110.26.
•The unit can be installed in indoor or outdoor loca-
tions.
•If installing indoors, an external switch must be
installed to be the PV rapid shutdown initiator, or
additional DC disconnects must be sourced and
installed on the PV circuits. See Photovoltaic
Rapid Shutdown for more information.
•If installing outdoors, mount the unit near the utility
service entrance to allow the inverter DC discon-
nects to be the compliant PV rapid shutdown initia-
tors. See Photovoltaic Rapid Shutdown for
more information.
•If using the inverter DC disconnects as the compli-
ant PV rapid shutdown initiator(s), verify the height
of the DC disconnects in the inverter do not exceed
6' 7" (2 m) to comply with NEC Article 404.8(A).
•Ensure proper labeling of PV equipment and add
placards where necessary to indicate location of
PV disconnects.
•If possible, avoid mounting locations where the
inverter may be subject to direct sunlight or where
liquids may be prone to drip/collect.
Standards
The PWRcell Inverter is designed and evaluated to the
following standards:
* UL 1741:2021 Ed.3
* UL 1741:2021 Ed.3 (Supplement SB)
- IEEE 1547:2018
- IEEE 1547.1:2020
* CSA C22.2#107.1:2016 Ed.4
NOTE: Refer to the latest version of this manual for the
most current product listings.
Immunity
Immunity testing was conducted in accordance with:
IEEE C62.41.2:2002, IEEE C62.45:2002, and IEEE
C37.90.2:2004 per IEEE 1547.1:2018, and IEEE
1547.1:2020.
Surge withstand capability, as per IEEE C62.41.2:2002
COR 2012 and IEEE C62.45:2002, was shown to meet
the following levels when applied to the AC Mains and
Ethernet terminals:
* 1.2x50µsec Combination: ±6kV
* 200A 100kHz Ringwave: ±6kV
* EFT: ±3kV
Note on DC Wiring and the NEC
Some electricians or installers may be unfamiliar with DC
wiring in a residential setting. Note the following:
•NEC 690.31 for DC PV circuits in buildings
•NEC 215.12(C)(2) for correct DC wiring identifica-
tion
Always adhere to applicable codes when marking and
installing DC conductors. See Table 3-1: REbus DC Wir-
ing Coloring Convention. Mark or flag all conductors for
their polarity as appropriate.
•It is recommended that REbus (+) conductors NOT
be green, white, gray, blue, or black.
•It is recommended REbus (-) conductors NOT be
green, white, gray, or red.
(000190)
DANGER
Loss of life. Property damage. Installation must
always comply with applicable codes, standards, laws
and regulations. Failure to do so will result in death
or serious injury.
WARNING
Electrocution. Refer to local codes and standards for
safety equipment required when working with a live
electrical system. Failure to use required safety
equipment could result in death or serious injury.
(000257)
(000182a)
WARNING
Equipment damage. Only qualified service personnel may
install, operate, and maintain this equipment. Failure to
follow proper installation requirements could result in death,
serious injury, and equipment or property damage.
Table 3-1. REbus DC Wiring Coloring Convention
Wire Color
REbus + (RE+) Red
REbus - (RE-) Black
Ground (GND) Green

Location and Standards
10 Installation and Owner’s Manual for Generac PWRcell Inverter
Photovoltaic Rapid Shutdown
The PV Link, SnapRS, and PWRcell Inverter are certified as Photovoltaic Rapid Shutdown Equipment (PVRSE).
Review Table 3-2: PVRSS Requirements and PWRcell PVRSE to determine what PWRcell equipment is required to
constitute an effective Photovoltaic Rapid Shutdown System (PVRSS). Refer to Generac PV Link & SnapRS Installa-
tion manual for more information on proper installation of those devices including commissioning instructions.
Following PV rapid shutdown initiation, controlled conductors will be brought within the limits defined in NEC 690.12 as
described in Table 3-2 above. The controlled conductors include:
•REbus conductors connecting PV Link(s) to the PWRcell Inverter (conductors leaving the array).
•PV conductors between modules in PV Link PV substring (conductors inside the array boundary).
NOTE: AC conductors exiting and entering the inverter are not considered controlled conductors for this application.
NOTE: Depending on the installation conditions (panel type, ambient temperature, etc.), leakage current methods
detailed in UL 1703, Section 21 may be used to indicate compliance with the stated limits as permitted by UL 1741,
Section 93.1.2.
PVRSS Initiation
There are three approved methods for initiating PV rapid shutdown with PWRcell equipment. Each method effectively
disconnects the PV input circuits from the inverter's internal DC bus. This disconnection is detected by the PV Links,
which in turn interrupt the PV source circuits. Interruption of the PV source circuits opens SnapRS devices, isolating PV
modules within the array. All three methods are considered suitable for installations where the inverter is located
outside of a one-family or two-family dwelling. In most situations, only Method 2 (external switch) or Method 3 (installer-
sourced DC disconnect) will be appropriate for installations where the Inverter is located inside of a one-family or two-
family dwelling (where the external device is located outside of the dwelling near the utility service entrance).
Appropriate signage and/or markings in compliance with NEC 690 must be provided by the installer.
Method 1 - PVRSS initiation via PWRcell Inverter DC disconnect(s) (outdoor installations)
1. Open the inverter lid.
2. Locate the PWRcell DC disconnects located to the left of the Generac Power Core.
3. Turn DC disconnects connected to PV sources to the OFF position.
Method 2 - PVRSS initiation via external switch connected to inverter STOP terminals (indoor and outdoor
installations)
NOTE: If installation includes a PWRcell Battery, the battery must be equipped with external STOP terminals. Battery
STOP terminals must be wired in series or parallel to the inverter STOP terminals. See PWRcell Battery Installation
& Owner's Manual for more details.
1. A UL listed, 12 VDC, 5 mA, lockable, weatherproof switch must be connected to the STOP terminals to use this
method.
Table 3-2. PVRSS Requirements and PWRcell PVRSE
NEC Adoption PVRSS Requirements (NEC 690.12) Required PWRcell PVRSE*
2011 or older No PVRSS requirements. N/A
2014
Controlled conductors leaving array limited to not
more than 30 volts within 10 seconds of rapid
shutdown initiation.
Generac PV Link(s)
2017, 2020 and follows
Controlled conductors leaving array limited to not
more than 30 volts within 30 seconds of rapid
shutdown initiation.
Controlled conductors located inside the array
boundary (or not more than 1 m (3ft) from the
point of penetration of the surface of the building)
shall be limited to not more than 80 volts within 30
seconds of rapid shutdown initiation.
Generac PV Link(s),
Generac SnapRS
(one per PV module)
*Depending on approved method used, the PVRSS may include the Generac PWRcell Inverter but the inverter is not required for an effective
PVRSS.

Location and Standards
Installation and Owner’s Manual for Generac PWRcell Inverter 11
a. The switch must indicate ON and OFF positions, where the OFF position opens the STOP terminal circuit.
STOP circuit terminals are normally closed.
2. Turn switch to the OFF position.
3. Upon initiation, the inverter display will read “Shutdown Initiated”.
See Section 5: Electrical Connections STOP Terminal Wiring for installation instructions.
Method 3 - PVRSS initiation via installer-sourced DC disconnect(s) (indoor and outdoor installations)
1. A UL listed, lockable, weatherproof DC disconnect rated for at least 420 VDC and 30 A must be installed
between the PV conductors leaving the junction box and the inverter DC inputs.
a. The switch must indicate ON and OFF positions, where the OFF position opens the PV circuit.
2. Turn DC disconnects to the OFF position.
NOTE: This equipment shall be installed and operated in an environment within the ratings and limitations of the equip-
ment as published in these installation instructions.
PVRSS Self-Test
After commissioning, a PVRSS self-test can be performed to validate the functionality of the PVRSS using one of the
methods described above. Alternatively, functionality of the PVRSS can be validated for a substring using the following
instructions.
1. On the PWRcell Inverter control panel, press the right arrow key until the first PV Link device page appears.
NOTE: The device page display should read Disabled. If it does not read Disabled, press the center button and disable
the PV Link.
2. Press the center button and select “Test PVRSS” to enter the ‘Testing PVRSS’ state. The display indicates ‘Test-
ing PVRSS’ during the test process, which can take up to three minutes. Upon successful completion, the display
will read ‘Test Success’.
Photovoltaic Hazard Control
2020 and 2023 NEC
The 2020 and 2023 NEC have multiple available methods for meeting rapid shutdown requirements within the array
boundary in section 690.12. One option is to deploy a listed PV hazard control system (PVHCS). The S2502HC PV
Link and the PWRcell Inverter are both UL 3741 listed PVHCE.
When installed in accordance with the guidelines provided in this section, the PWRcell Inverter and S2502HC PV Link,
in combination with properly rated solar panels (see requirements below), and optionally, a properly rated external
STOP switch (see requirements below) form a comprehensive PVHCS, compliant with the requirements of NEC
690.12(B)(2). PVRSS functionality is retained for conductors leaving the array boundary in accordance with NEC
690.12(B)(1).
When a rapid shutdown is initiated (see Photovoltaic Rapid Shutdown ), the properly installed PVHCS will ensure
hazards within the array are sufficiently reduced in accordance with UL 3741.The rapid shutdown initiator performs the
PVHCE initiation, and must be installed in accordance with requirements for rapid shutdown initiators per the NEC and
per the additional requirements in Table 3-3: Required PVHCE Equipment and Component Ratings.
Refer to the S2502HC installation manual for instructions on how to design the array in accordance with PVHCS
requirements.
Required PVHCE Equipment and Component Ratings
The equipment listed in the following table must be installed in accordance with the manufacturers installation instruc-
tions in order to establish a UL 3741 listed PVHCS. Entries that contain the text “(optional)” are not required to establish
a listed PVHCS, but must meet the listed rating requirements if they are used as part of the PVHCS.
WARNING
(000786)
Read Instructions. To reduce the risk
of injury, read all instructions. Failure
to do so could result in death or seri-
ous injury.

Location and Standards
12 Installation and Owner’s Manual for Generac PWRcell Inverter
Voltage and Frequency Trip Settings
The PWRcell Inverter ships from the factory in compli-
ance with UL 1741. The inverter nameplate (Figure 2-2)
specifies compliance with applicable UL 1741 Supple-
ments (e.g. UL 1741-SA, UL 1741-SB). A PWRcell
Inverter compliant with UL 1741-SA is shipped with
default settings per IEEE 1547-2003. A PWRcell Inverter
compliant with UL 1741-SB is shipped with default set-
tings per IEEE 1547-2018. A list of the default values and
range of adjustability for UL 1741 SB tested functions is
found in Table 10-1. Where local Electric Utility require-
ments for smart inverters specify non-default inverter set-
tings (per the locally adopted IEEE 1547 grid standard),
follow the steps in the Set Inverter Grid Compliance sec-
tion of this manual.
NOTE: Use of Grid Profiles in compliance with local
Electric Utility smart inverter requirements may exceed
the tested range of adjustment for UL 1741-SB listed
inverters.
Voltage Trip
See Table 3-4 and Table 3-5 for the default fixed voltage
trip settings. All over voltage and under voltage trip condi-
tions result in a 300-second restart delay time after the
trip setting has been exceeded for the listed clearing
time.
The inverter is disconnected from the grid during this
300-second delay.
Frequency Trip
See Table 3-4 and Table 3-5 for the default fixed fre-
quency trip settings. All over frequency and under fre-
quency trip conditions result in a 300-second restart
delay time after the trip setting has been exceeded for
the listed clearing time.
The inverter is disconnected from the grid during this
300-second delay.
*This unit or system is provided with fixed trip limits and shall not be aggregated above 30 kW on a single point of common coupling.
Table 3-3. Required PVHCE Equipment and Component Ratings
Required
Device Manufacturer Model Required Ratings/Listings
PV Link Generac Power Systems Inc. S2502HC
Max input voltage < 165 VDC, Type 4X rated, Operating
Temperature Range -20°C to 70°C, Rapid Shutdown
Device Compatible.
Inverter Generac Power Systems Inc. XVT076A03 Max Power: 7600 W. Type 3R rated, Operating Tempera-
ture Range -20°C to 50°C. Not for roof mount.
PV Modules Various Various
Series connected panels with NEC temperature corrected
maximum Voc < 165 VDC, listed to UL 1703 and/or UL
61730-1 and UL 61730-2 (excluding Class 0 and Class 1)
External STOP
Switch (optional) Various Various Type 3R rated. Operating Temperature Range Range 40°C to 60°C, 12 VDC, 5 mA. Not for roof mount.
Table 3-4. Voltage and Frequency Trip Default Settings (UL 1741-SA)*
Voltage Trip Frequency Trip
Trip Function Voltage
(% of nominal) Clearing Time (s) Trip Function Frequency (Hz) Clearing Time (s)
OV2 120 0.16
OV1 110 1 OF1 60.5 0.16
UV1 88 2 UF1 59.3 0.16
UV2 50 0.16
Table 3-5. Voltage Trip and Frequency Trip Default Settings (UL 1741-SB)
Voltage Trip Frequency Trip
Trip Function Voltage
(% of nominal) Clearing Time (s) Trip Function Frequency (Hz) Clearing Time (s)
OV2 120 0.16 OF2 62 0.16
OV1 110 13 OF1 61.2 300
UV1 88 21 UF1 58.5 300
UV2 50 2 UF2 56.5 0.16

Installing PWRcell Inverter
Installation and Owner’s Manual for Generac PWRcell Inverter 13
Section 4: Installing PWRcell Inverter
Mounting Clearances
Figure 4-1. PWRcell Inverter Dimensions and Mounting Clearances
Mounting Bracket Dimensions
Figure 4-2. Mounting Bracket Dimensions
4 in
(10.16 cm)
28 in
(71.15 cm)
8 in
(20.32 cm)
28-1/2 in
(72.4 cm)
36 in
(91.44 cm)
8 in
(20.32 cm)
19-1/4 in
(48.9 cm)
8-1/2 in
(21.6 cm)
20 in
(50.8 cm)
8 in
(20.32 cm )
24-1/2 in
(62.23 cm)
010508
16 in
(40.64 cm)
1-1/2 in
(3.81 cm)
2-3/8 in
(6.03 cm)
009990

Installing PWRcell Inverter
14 Installation and Owner’s Manual for Generac PWRcell Inverter
Mounting the Inverter
1. Verify mounting location adheres to the following
requirements:
•Location must meet all PWRcell Inverter
requirements listed in Section 3 of this manual.
See Location and Standards for more
information.
•Inverter must be mounted upright on a vertical wall.
•Never obstruct intake or exhaust vents.
•Never allow water to enter intake or exhaust vents.
•Observe all mounting clearances. See Mounting
Clearances.
2. Secure mounting bracket mounting surface
through mounting holes.
•Fasteners must adequately secure the 62.7 lbs
(28.4 kg) inverter weight to the wall.
•Fasteners must be suitable for the mounting
surface.
•Fasteners must engage at least two studs or other
structural members.
•Mounting bracket has clearance holes for 1/4 in
fasteners with slots to accommodate different stud
spacings.
3. See Figure 4-3. Insert mounting bracket tabs (A)
into inverter body slot (B).
NOTE: Figure 4-3 is for illustration purposes only.
Figure 4-3. Mounting Inverter onto Bracket
4. See Figure 4-4. Secure the bottom of the inverter
to wall with two fasteners through mounting holes
(C). Holes are spaced at 11 1/4 in. from each other.
Use anchors or blocking as needed.
Figure 4-4. Mounting Holes
(000641a)
CAUTION
Equipment damage. Mount inverter to a strong, stable surface.
Never mount to drywall, plaster, or other non-structural wall
treatments. Failure to mount inverter to a strong, stable surface
could result in equipment or property damage.
A
B
009991
C
009992

Electrical Connections
Installation and Owner’s Manual for Generac PWRCell Inverter 15
Section 5: Electrical Connections
Accessing Wiring Compartment
IMPORTANT: The inverter interior is not weather-proof.
Do not open the inverter front cover when wet or during
rain/snowfall.
See Figure 5-1 . To access the wiring compartment:
1. Open inverter front cover by lifting the bottom to
just beyond horizontal (B) and pushing inward (C).
2. Locate wiring compartment cover (D).
3. Remove five M4X10 screws (E) and wiring
compartment cover.
4. Verify all PWRcell DC and AC terminals are below
10 V, using a multi-meter.
Figure 5-1. Wiring Compartment
PWRcell Inverter Wiring Compartment
Figure 5-2. PWRcell Inverter Wiring Compartment
(000600)
DANGER
Electrocution. Initiate a system-wide shutdown and turn the
PWRcell DC Disconnect Switch OFF on all connected
batteries before performing service. Failure to do so will
result in death, serious injury, or equipment and property
damage.
(000642)
DANGER
Electrocution. Verify all system voltages are safe before
wiring. Disconnect all AC and DC sources of power before
touching terminals. Failure to ensure no dangerous
voltages are present on conductors and terminals before
wiring will result in death or serious injury.
C
010238
B
ED
A
APWRcell DC Disconnects ISTOP Terminals
BREbus Bi-directional DC Terminals JProtected Loads Disconnect
CInternet Connection KAC Grid Connection Terminals
DDC Main Fuses LProtected Loads Terminals
ECurrent Transformers (CTs) Accessory Ports MGrounding Bar
FAutomatic Transfer Switch (ATS) Accessory Port NRGM PWR / Gen Inhibit
GREbus Beacon Port OFast Blow Mini Fuses 1 A 250 V
HAuthorized Generac Personnel Only
BC
D
M
L
K
J
I
H
G
F
E
A
011235
N
O

Electrical Connections
16 Installation and Owner’s Manual for Generac PWRCell Inverter
Knockout Dimensions and Locations
NOTE: All knockouts are combination knockouts, except
for the 1/4 in trade knockout at the top of the left side
which is intended only for mounting an optional LTE
modem antenna.
See Figure 5-3 for knockout locations and Table 5-1 for
available knockout sizes and quantities.
When using knockouts:
•Install reducing washers to accommodate smaller
conduit sizes.
•Install rain-tight or wet locations hubs in
compliance with UL514B.
Figure 5-3. Knockout Locations
Table 5-1. Combination Knockout Size and Quantity
Combination Knockout Size Quantity
3/4 in X 1 in 6
1/2 in X 3/4 in 7
0.575 in use only for LTE Modem Antenna 1
42 mm
1-21/32 in
50 mm
1-31/32 in
137 mm
5-13/32 in
97 mm
3-13/16 in
140 mm
5-17/32 in 2-13/16 in
72 mm
56 mm
2-7/32 in
40 mm
1-19/32 in
552 mm
21-23/32 in
50 mm
1-31/32 in
45 mm
1-3/4 in
55 mm
2-5/32 in
55 mm
2-5/32 in
26 mm
1 in
58 mm
2-9/32 in
62 mm
2-7/16 in
50 mm
1-31/32 in
48 mm
1-7/8 in
55 mm
2-5/32 in
55 mm
2-5/32 in
35 mm
1-3/8 in
10 mm
13/32 in
28 mm
1-3/32 in
011234