Genie CCTV PIXIM VRD83SPX Manual

1
PIXIM Digital Day/Night Vandal Resistant Dome Camera
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
◆ Do NOT use power sources other than those specified.
This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:

How to Use the Camera 14
■Menu 14
■Settings 15
ㆍPRESETS 16
ㆍEXPOSURE 17
ㆍWDR 19
ㆍWHITE BALANCE 20
ㆍDAY&NIGHT 21
ㆍIMAGE ADJ. 22
ㆍSPECIAL 24
- CAMERA ID
- VIDEO OUT
- DZOOM
- MOTION
- PRIVACY MASK
- SYNC
- RESET
ㆍEXIT MEMU 29
25
26
26
26
27
28
28
Troubleshooting 30
Specifications 32
2
PIXIM Digital Day/Night Vandal Resistant Dome Camera
3
PIXIM Digital Day/Night Vandal Resistant Dome Camera
Features
Warnings and Precautions
Names and Functions of Parts
Installation
Cable Connection
4
6
9
Dimensions 11
12
13
■LENS 10
■OSD 10
■VBS-EXTRA 11
■3 AXIS BRACKET 11
■SMPS 11
Components 8
■Contents

4
PIXIM Digital Day/Night Vandal Resistant Dome Camera
5
PIXIM Digital Day/Night Vandal Resistant Dome Camera
Additional Functions
SYNC (INT/LL), SENS-UP, FREEZE, FLIP
(H/V-REV), D-ZOOM, SHARPNESS and
PRIVACY functions are provided.
Controlled by OSD Menu
The camera can be controlled by selecting
text displayed on the monitor screen.
Motion Detection
Since the camera detects motion without any
additional external sensor, you can monitor
activity more efficient.
Programmable GAMMA Processing
Weatherproof (IP67)
■Features Warning ■
The camera requires periodic inspection.
Contact an authorised technician to carry out the inspection.
Stop using your camera when you find it malfunctioning.
If the camera emits smoke or is unusually hot for a long period,
a fire may be caused.
Do not Install the camera on a surface that can not support it.
If the camera is installed on an inappropriate surface, it may fall
and cause injury.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not dis-assemble the camera.
It may result in an electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in a fire or other hazards.
3 Axis built-in Vandal Resistant
Dome Housing
Wide Dynamic Range (WDR)
The camera delivers clear high quality pictures,
even when backlit, by increasing exposure in
dark areas while decreasing it in bright areas;
a corrected image with clear details results.
ㆍ120dB maximum dynamic range
High Resolution Colour for Crisp,
Clear Video
ㆍProgressive image capture
ㆍ690TVL Effective
Day & Night
The camera identifies whether it is day or night
and automatically switches to the appropriate
mode, depending on its environment. By day,
the camera switches to colour mode in order to
maintain optimal colour. At night, it switches to
B/W mode so as to obtain better picture definition.
High Sensitivity for low-light
images
The built-in high sensitivity PIXIM SEAWOLF
Sensor enables a clear image even at 0.1Lux
DNR (Digital Noise Reduction)
The amount of low illuminance noise has been
significantly reduced, and the signal-to-noise
ratio (S/N ratio) as well as horizontal resolution,
have been improved resulting in a clear and
sharp image image even in low light.

6
PIXIM Digital Day/Night Vandal Resistant Dome Camera
7
PIXIM Digital Day/Night Vandal Resistant Dome Camera
Do not install the camera in
extreme temperature conditions.
Do not install the camera under
unstable lighting conditions.
Do not touch the front lens of the
camera.
Only use the camera under conditions
where temperatures are between
-10˚C and +50˚C. Be especially
careful to provide ventilation when
operating under high temperatures.
It can cause the image quality to be
poor.
Severe lighting change or flicker can
cause the camera to work improperly.
This is one of the most important parts
of the camera. Be careful not to leave
fingerprints on the lens cover.
Do not install or use the camera in an
environment where the humidity is high.
It can cause malfunctions to occur.
Do not drop the camera or protect
it from physical shocks.
ㆍIf the camera is exposed to spotlight or an object reflecting strong light,
smear or blooming may occur.
ㆍPlease check the power supply satisfies the normal specification before
connecting the camera.
If exposed to radioactivity the CMOS
will fail.
Do not expose the camera to
radioactivity.
■Precautions

8
PIXIM Digital Day/Night Vandal Resistant Dome Camera
9
PIXIM Digital Day/Night Vandal Resistant Dome Camera
■Components Names and Functions of Parts ■
4. WIRE FOR VBS-EXTRA
5. INSTRUCTION GUIDE
1. COLOUR DOME CAMERA
2. SCREWS
3. WRENCH
③
④
⑤
②①

10
PIXIM Digital Day/Night Vandal Resistant Dome Camera
11
PIXIM Digital Day/Night Vandal Resistant Dome Camera
■Names and Functions of Parts Names and Functions of Parts ■
②OSD PCB
●SET button : Used for the menu display. This button can be used to
confirm settings after changing the value of the selected function or
current conditions.
●UP & DOWN buttons : Used for selecting items by moving the cursor
up or down on the menu screen.
●LEFT & RIGHT buttons : Used when changing item values, by moving
the cursor to the left or right on the menu screen.
①LENS : Vari-Focal DC Auto Iris Lens
Dimensions ■
③VBS-EXTRA FOR CONNECTING TO LCD
Please use the supplied wire when connecting to an external monitor.
VBS-EXTRA
⑤3 AXIS BRACKET
Please loosen screws and fix tilted and panned position.
④SMPS PCB FOR DUAL POWER - IF APPLICABLE
(unit : mm)
100.0 152.0
46.0
83.5
104.7
DOWNUPSETRIGHTLEFT

■Installation
Dome Base
Decoration Ring
Surface Mount Bracket
Security Screws
with "O" ring
Dome Cover
DC only
AC24V
DC12V AC IN
DC IN AC IN DC IN
VIDEO
POWER
Cable Connections ■
1. Dome Base Mounting
- Open the dome cover by loosening the 3 screws using the special
wrench provided.
- Mount the base of camera to a sturdy surface using the 4 screws (1.5
inch) and the 4 premade holes on the base of the dome.
2. Power Connection & Monitor Impedance
- DC12V/300mA regulated power supply (DC12V only)
AC24V Class 2 power supply (AC24V/DC12V)
- To avoid fire or shock hazard, always use a CE listed power supply.
- Set the monitor impedance switch to 75Ω. Check the impedance
switch if the screen appears blurred.
3. Camera Module Adjustment
- Loosen screws for the 3-axis camera bracket to adjust the cameras
angle of view.
- Make sure to retighten the camera bracket screws.
- Use the OSD buttons to select the different camera functions.
4. Dome Cover Mounting
- Replace the dome cover to the base and tighten the 3 screws.
12
PIXIM Digital Day/Night Vandal Resistant Dome Camera
13
PIXIM Digital Day/Night Vandal Resistant Dome Camera

14
PIXIM Digital Day/Night Vandal Resistant Dome Camera
15
PIXIM Digital Day/Night Vandal Resistant Dome Camera
■How to Use the Camera
■
Menu
Settings can be made using the 5 buttons located in the camera.
1. Press the SET button
ㆍSettings can now be made. The SETUP menu is displayed on the monitor.
2. Select a menu item from the list available by using the UP and DOWN
buttons.
ㆍFuntions are selected using up and down buttons.
ㆍThe selected position is displayed in blue.
■
Settings
SETUP
PRESETS
EXPOSURE..
WDR
WHITE BALANCE
DAY&NIGHT
IMAGE ADJ..
SPECIAL..
EXIT MENU.
NORMAL
MIDDLE
ATW
AUTO..
ㆍNORMAL
SETUP menu
PRESETS
EXPOSURE
WDR
WHITE BALANCE
DAY&NIGHT
IMAGE ADJ.
EXIT MENU
ㆍMIDDLE
ㆍLOW
ㆍRESET
ㆍCAMERA ID
ㆍMOTION
ㆍATW
ㆍAWB
ㆍBACKLIGHT
ㆍFREEZE
ㆍAUTO
SPECIAL
ㆍVERSION
ㆍCANCEL
ㆍCOLOR GAIN
ㆍINDOOR
ㆍMANUAL
ㆍHIGH
ㆍVIDEO OUT
ㆍPRIVACY MASK
ㆍINDOOR
ㆍSAVE&EXIT
ㆍFLIP
ㆍGAMMA
ㆍCOLOR
ㆍLENS SELECT
ㆍDNR
ㆍCOLOR ROLL ㆍSENS-UP
ㆍEXPOSURE MODE
ㆍBLC
ㆍHIGHLIGHT
ㆍAGC
ㆍOUTDOOR
ㆍOUTDOOR
ㆍDEFAULT
ㆍSHARPNESS
ㆍUSER
ㆍDZOOM
ㆍSYNC
ㆍBW
ㆍFOCUS
DOWNUPSETRIGHTLEFT

16
PIXIM Digital Day/Night Vandal Resistant Dome Camera
17
PIXIM Digital Day/Night Vandal Resistant Dome Camera
■How to Use the Camera
SETUP
PRESETS
EXPOSURE..
WDR
WHITE BALANCE
DAY&NIGHT
IMAGE ADJ..
SPECIAL..
EXIT MENU.
NORMAL
MIDDLE
ATW
AUTO..
3. Set up a selected item by using the Left and Right buttons.
4.Tofinishandsavethesettings,select'EXITMENU' and press the SETbutton.
Select the function
using the UP or
DOWN button.
Change the status
using the LEFT or
RIGHT button.
PRESETS
Note
• An item with the .. icon also has sub-menus. To select a sub-menu,
press the SET button.
SETUP
PRESETS
EXPOSURE..
WDR
WHITE BALANCE
DAY&NIGHT
IMAGE ADJ..
SPECIAL..
EXIT MENU.
NORMAL
MIDDLE
ATW
AUTO..
● NORMAL : Normal environment.
● INDOOR : Indoor environment.
● OUTDOOR : Outdoor environment.
● BACKLIGHT : Backlight environment.
LENS MENU
DC GAIN
AI THRESH
PREVIOUS PAGE..
0 120 255
-24
-48 60
EXPOSURE
SETUP
PRESETS
EXPOSURE..
WDR
WHITE BALANCE
DAY&NIGHT
NORMAL
MIDDLE
ATW
AUTO..
When the SETUP menu screen is displayed, select‘EXPOSURE’by
using the Up and Down buttons so that the arrow indicates‘EXPOSURE’.
● LENS SELECT :Using this function, you can control the screen brightness.
ㆍDC / Manual : Select Lens Type.
EXPOSURE
LENS SELECT
BLC
EXPOSURE MODE
AGC
DNR
HIGHLIGHT
COLOR ROLL
SENS-UP
PREVIOUS PAGE..
DC..
OFF
50i
MEDIUM
MIDDLE
ON
OFF
2X

18
PIXIM Digital Day/Night Vandal Resistant Dome Camera
19
PIXIM Digital Day/Night Vandal Resistant Dome Camera
■How to Use the Camera
● EXPOSURE MODE : To select the number of fields and number
of exposure cycles.
- 50i/25p selectable
● AGC (AUTO GAIN CONTROL) : In dark environments, the higher the
gain level, the brighter the screen but the higher the noise.
- OFF / LOW / MEDIUM / HIGH selectable
● DNR (Digital Noise Reduction) : The level of background noise in low
light decreases automatically as the level of gain changes.
- OFF / LOW / MIDDLE / HIGH selectable
● HIGHLIGHT : To optimise the scene when high dynamic range lighting
is detected.
- ON : bright parts of the image are most visible.
- OFF : dark parts of the image are most visible.
● COLOR ROLL : To control a detector that finds colour fluorescent roll.
- OFF / LOW / HIGH selectable
● SENS-UP : When it is night or dark, the camera automatically detects
the light level and maintains a clear picture if this mode is activated.
- 2X, 4X, 8X, 16X, 32X
- OFF : Deactivates the SENS-UP function.
● BLC : To optimize the scene when there is a strong backlight behind
the object.
- ON / OFF selectable
ADVANCED BLC SETUP
PERCENTILE
PREV. SAVE. CANCEL.
10 5035
WDR
● WDR : When the image has simultaneous bright and dark areas, the
Wide Dynamic Range makes both areas distinct.
- LOW / MIDDLE / HIGH / USER selectable
WDR LEVEL
BIAS
LIMIT
PREVIOUS PAGE..
2
36
-30 30
036
SETUP
PRESETS
EXPOSURE..
WDR
WHITE BALANCE
DAY&NIGHT
IMAGE ADJ..
SPECIAL..
EXIT MENU.
NORMAL
MIDDLE
ATW
AUTO..

20
PIXIM Digital Day/Night Vandal Resistant Dome Camera
21
PIXIM Digital Day/Night Vandal Resistant Dome Camera
■How to Use the Camera
MANUAL WHITE BALANCE
RED
BLUE
PREVIOUS PAGE..
-18
13
-20 20
-20 20
WHITE BALANCE
Use the White Balance function to adjust the screen colours.
1. Position the cursor to point to WHITE BAL on the SETUP menu screen,
select using the Up and Down buttons.
2. Select the desired mode using the Left and Right buttons.
SETUP
PRESETS
EXPOSURE..
WDR
WHITE BALANCE
DAY&NIGHT
IMAGE ADJ..
SPECIAL..
NORMAL
MIDDLE
ATW
AUTO..
※Select one of the following 5 modes, as appropriate.
● ATW : The ATW mode continuously monitors.
● INDOOR : Select when the colour temperature is between 4000˚K
and 8500˚K
● OUTDOOR : Select when the colour temperature is between 2000˚K
and 11000˚K
● AWB : To obtain the optimum state under the current luminance
levels, direct the camera to point toward a sheet of white paper and
press the SET button. If the environment changes, including the light
source, the white balance will require re-adjustment.
● MANUAL : Select to "fine-tune" the White Balance manually. Set
White Balance first using the ATW or AWB mode. Afterwards switch
to MANUAL mode, fine-tune the White Balance and then press
the SET button.
DAY&NIGHT
Note
• Under the following conditions White Balance may not work properly.
In such cases, select the AWC mode.
① When the colour temperature of the subject environment has a very
high temperature range (e.g. clear sky, or sunset)
② When the ambient illumination of the subject is low.
③ If the camera is directed toward a fluorescent light, or is installed in
a place where illumination changes dramatically, the White Balance
operation may become unstable.
● AUTO : This camera has a function which automatically changes to
the appropriate mode according to lighting levels. To set up the switching
time for the AUTO mode press the SET button.
SETUP
PRESETS
EXPOSURE..
WDR
WHITE BALANCE
DAY&NIGHT
IMAGE ADJ..
SPECIAL..
EXIT MENU.
NORMAL
MIDDLE
ATW
AUTO..

22
PIXIM Digital Day/Night Vandal Resistant Dome Camera
23
PIXIM Digital Day/Night Vandal Resistant Dome Camera
■How to Use the Camera
● COLOR : The picture is displayed in colour.
● B/W : The picture is always displayed in black and white.
When the SETUP menu screen is displayed, select 'IMAGE ADJ.' using
the Up and Down buttons.
SETUP
PRESETS
EXPOSURE..
WDR
WHITE BALANCE
DAY&NIGHT
IMAGE ADJ..
SPECIAL..
EXIT MENU.
NORMAL
MIDDLE
ATW
AUTO..
IMAGE ADJ.
● FREEZE : View still pictures.
- OFF / ON selectable
●FLIP : OFF / HORIZ / VERT / BOTH selectable
●SHARPNESS : The outline of the video image becomes cleaner and
more distinctive as the level of SHARPNESS increases. If the level gose
up excessively, however, it may affect the video image and generate noise.
- The available range of level is -8 ~ 8
●COLOR GAIN : To control the colour level in the video.
- The available range of level is -8 ~ 8
●GAMMA : Users can change the gamma setting between 25 and100
IMAGE
FREEZE
FLIP
SHARPNESS
COLOR GAIN
GAMMA
FOCUS..
PREVIOUS PAGE..
OFF
OFF
-8 0 8
0
-8 8
2545 100
BOTHVERT
HORIZOFF
DAY&NIGHT SETUP
NIGHT MODE
TIME DELAY
PREVIOUS PAGE..
BW+burst
BW
COLOR
1
0255

24
PIXIM Digital Day/Night Vandal Resistant Dome Camera
25
PIXIM Digital Day/Night Vandal Resistant Dome Camera
■How to Use the Camera
SPECIAL
When the SETUP menu screen is displayed, select 'SPECIAL' by using
the Up and Down buttons so that the arrow indicates 'SPECIAL'.
SETUP
PRESETS
EXPOSURE..
WDR
WHITE BALANCE
DAY&NIGHT
IMAGE ADJ..
SPECIAL..
EXIT MENU.
NORMAL
MIDDLE
ATW
AUTO..
● FOCUS : To adjust the lens focus.
FOCUS DETECTOR
FOCUS METER
SET FOCUS REGION..
PREVIOUS PAGE..
88
SET FOCUS REGION
●CAMERA ID : User can enter a unique name for the respective camera.
The maximum length of the ID is ten characters.
ㆍYou can choose the ON and OFF with the selector. If you select ON,
the entered camera ID is displayed at the selected position in the video
picture (normal operation).
ㆍPlease select the setup button while in On mode.
ㆍSelect the desired position with the selector.
① Move the cursor to the letter required by using the Set-Up button.
② Select an ID from A,B~Y,Z, a,b~y,z, 0,1~8,9 by using the LEFT and
RIGHT buttons.
③ Repeat the above steps until the ID is complete.
CAMERA ID
ID
POSITION
PREVIOUS PAGE..
CAM-001
UP-LEFT
CAMERA ID
ID
POSITION
PREVIOUS PAGE..
CAM-001
UP-LEFT
SPECIAL
CAMERA ID
VIDEO OUT..
DZOOM
MOTION
PRIVACY MASK..
SYNC
RESET
PREVIOUS PAGE..
OFF
OFF
OFF
INT

26
PIXIM Digital Day/Night Vandal Resistant Dome Camera
27
PIXIM Digital Day/Night Vandal Resistant Dome Camera
■How to Use the Camera
●DZOOM : Digital P/T/Z are used to create a zoom lens effect.
Zoom Factor (1X to 4X), Pan (±100%, center of image can be moved
to left and right edges of screen), Tilt (±100%, center of image can
be moved to top and bottom edges of screen)
●MOTION : This product has a feature that allows you to observe
movements of objects in on the screen, hence a single individual can
conduct supervision efficiently.
The camera detects an object's movement by sensing disparity of
outline, and level of brightness and colour.
DZOOM
ZOOM
PAN
TILT
PREVIOUS PAGE..
1
0
0
-100 100
14
-100 100
VIDEO STANDARD
VIDEO SELECT
VIDEO LEVEL
SYNC LVL
BURST LVL
COLOR BAR
PREVIOUS PAGE..
0
0OFF
PAL
80 110 150
-16 15
-16 15
- VIDEO STANDARD : You can control NTSC / PAL, Video level,
Sync level, Burst level.
① Select the position where the ID is to be displayed by using the
LEFT and RIGHT buttons.
●VIDEO OUT : Move the cursor to select the video system
MOTION DETECTION
ACTIVITY THR.
MESSAGE TIME
SETUP MOTION ZONE..
PREVIOUS PAGE..
0 25 255
1 3 10
MOTION ZONE SETUP
●PRIVACY MASK : Hide an area you want to hide on the screen.
ㆍWhite : MOTION ZONE Position movement
Green : MOTION ZONE Size enlargement
Red : MOTION ZONE Size reduction
ㆍFor MOTION ZONE Confirm, long press SET button
PRIVACY MASK SETUP
PRIVACY MASK
MASK COLOR
PREVIOUS PAGE..
OFF
WHITE

28
PIXIM Digital Day/Night Vandal Resistant Dome Camera
29
PIXIM Digital Day/Night Vandal Resistant Dome Camera
■How to Use the Camera
●SYNC : Two synchronisation modes are available, INTERNAL and
EXTERNAL LINELOCK. In LINE-LOCK mode, it synchronises the
video signal between cameras without a synchronous generator.
The line-lock synchronisation is only used in areas of 60Hz (NTSC)
/ 50Hz (PAL).
- INT : Internal synchronisation
- LL : External line-lock synchronisation
ㆍIf 'LL' is selected, it can be adjusted to the desired phase.
Press the SET button.
ㆍAdjust to the desired phase from 0 to 624.
LINE LOCK
V PHASE
PREVIOUS PAGE..
0 299 624
ENABLE MASKS (1 to 6)
MASK 1
MASK 2
MASK 3
MASK 4
MASK 5
MASK 6
PREV. NEXT.
ON
OFF
OFF
OFF
OFF
OFF
ENABLE MASKS (7 to 12)
MASK 7
MASK 8
MASK 9
MASK 10
MASK 11
MASK 12
PREVIOUS PAGE..
OFF
OFF
OFF
OFF
OFF
OFF
ㆍWhite : PRIVACY-ZONE
Position movement
Blue: PRIVACY-ZONE Size
enlargement or reduction
ㆍFor PRIVACY-ZONE Confirm,
long press SET button
●RESET : Resets the camera.
EXIT MENU
VERSION :
SAVE&EXIT
DEFAULT
CANCEL
7.3.2-7.0.281
EXIT MENU.
●VERSION : 7.3.2-7.0.281
●SAVE&EXIT : Saves all the setting menus and then exits.
●DEFAULT : Resets the camera settings to the factory defaults.
●CANCEL : Cancel to the camera settings.

If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an
authorised technician.
Problem
Nothing appears on
the screen.
The image on the
screen is dim.
•Check the power connections.
•Check the VIDEO signal line connection.
• Make sure the lens is clean. Clean the lens with a
soft clean lint free cloth.
•Adjust the monitor contrast & brightness controls.
• Re-position the camera if necessary.
The image on the
screen is dark. •Adjust the contrast control of the monitor.
•
If you have an intermediate device, set the 75Ω/ Hi-z
properly.
The camera is not working
properly, and the surface
of the camera is hot.
•Check that an appropriate power source is
connected to the camera.
The Motion Detection
function does not
work.
•Check that MOTION DET in the SPECIAL SETUP
is not set to 'OFF'.
Solution
30
PIXIM Digital Day/Night Vandal Resistant Dome Camera
31
PIXIM Digital Day/Night Vandal Resistant Dome Camera
■
Troubleshooting
Problem
Colour is not correct. • Check the WHITE BAL settings in the SETUP menu.
The screen flickers
continually.
•Check that the camera is not facing toward the
sun.
Solution

※POWER OPTION - DC12V Only : VRD83SPX/12
32
PIXIM Digital Day/Night Vandal Resistant Dome Camera
ITEM
Image Sensor
Signal processing
Transfer Format
Sync. System
Effective Pixels
Lens
HorizontalAngleof View
Dynamic Range
Horizontal Resolution
Min. Illumination
Day & Night
White Balance
WB Range
Shutter Speed
Sens-up
Privacy Masking
AGC
Image Flip
Camera ID
S/N Ratio
Video Output
OSD
Operating Humidity
Operating Temp.
Weatherproof
Weight
Power Consumption
PIXIM 1/3" High Sensitivity Digital Sensor
17-bit Digital Signal Processing
Progressive with Segmented Frames
Internal / Line Lock
758(H) x 540(V)
Tamron 2.8mm ~10.5mm DC AI VF Lens
93.7˚~ 28.3˚
120dB(Max), 102dB(Typical)
690TVL Effective
0.1Lux
AUTO / COLOR / B/W
ATW / AWB / INDOOR / OUTDOOR / MANUAL
2000˚K~11,000˚K
up to 1/30, 720 sec
AUTO / OFF (Selectable x2 ~ x32)
12 Zones
OFF / LOW / MEDIUM / HIGH
OFF / HORIZ / VERT / BOTH
ON / OFF
More than 50dB
Composite video output 75 ohm terminated
Built-in
30% ~ 90% RH
-10˚C to 50˚
IP67
Appro. 1,100g
160mA (DC12V Only)
170mA (AC24V) / 250mA (DC12V)
SPEC.
■Specifications

Edition. GN-OCTOBER 2011
GENIE CCTV LTD.
CCTV House, City Park, Watchmead, Welwyn Garden City, Hertfordshire, AL7 ILT
Tel : [phone] Fax : [phone]
www.geniecctv.com
PIXIM Digital Day/Night
Vandal Resistant
Dome Camera
Instruction Guide
Model : VRD83SPX
VRD83SPX/12