Genie CCTV ASD276 Manual

Model : ASD276
ASD376
Instruction Guide
Vandal Resistant
PTZ Day/Night Camera

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN THE COVERS.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONAL
This lightning flash with arrowhead symbol is intended to alert the user to
the presence of un-insulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
This exclamation point symbol is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
This Device compiles with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interface, and
(2) This device must accept any interference received, including
interference that may cause undesired operations.
Speed Dome Camera Instruction Manual 2/50

Speed Dome Camera Instruction Manual 3/50
Important Safety Guide
1. Read, heed and follow all the Instructions
Read all the safety and operating instructions before using the product.
2. Keep this manual
Keep this manual for future reference.
3. Attachments / Accessories
Use only the attachments or accessories specified by the manufacturer.
4. Installation
Do not install near any heat sources such as radiators, boilers, stoves, or any other
appratus,including amplifiers,that produceheat. Improperly installed product may fall
causing serious injuries and damage to the product.
Do not block any ventilation holes or openings. Install in accordance with the
manufacturer’s instructions.
Use only with suitable mounting options, devices, or bracketry specified by the
manufacturer.
Installation should only be carried out by qualified personnel and conform to all
the instructions issued by the manufacturer.
Refer all servicing to qualified service personnel.
This product is specifically marked as IP66 and tested to this protection level by the
manufacturer, it is designed for indoor and outdoor use and can be exposed to rain
and moisture.
Do not place unnecessary loadson the product.
Use stainless steel hardware to fasten the mount.
To prevent damage from water ingress, when installing the product outdoors, apply
sealant properly around cable entry holes.
These servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock, do not perform any servicing other that contained in the
operating instructions unless you are qualified to do so.
Use only replacement parts specified by the manufacturer.
5. Power source
This product should only be operated from the type of the power source indicated on the
product label.
NOTICE

Speed Dome Camera Instruction Manual 4/50
Caution
Operating
Before using, make sure the power supply and mains are properly installed.
While operating, if any abnormal condition or malfunction is observed, stop using the
product immediately and contact your distributor.
Handling
Do not disassemble or tamper with the parts inside the product.
Do not drop or subject the product to shock and vibration,as this can damage the
product.
Care must be taken when cleaning the clear dome cover. Scratches and dust
will ruin the quality of the images. Only use a clean lint free cloth.
Installation and Storage
Do not install the product in areas of extreme temperature which exceed the stated
range.
Avoid installing in humid or dusty places.
Avoid installing in places where radiation is present.
Avoid installing in places where there are strong magnetic fields and electric signals.
Avoid installing in places where the product would be subject to strong vibrations.
NOTICE

Speed Dome Camera Instruction Manual 5/50
①Introduction
Features 6
Package Components 9
Main Part Description 10
②Installation
DIP Switch Setup 11
Installation with Ceiling Mount Bracket 14
Installation with Wall Mount Bracket 15
Wiring and Cabling 16
③Operation
Check Point before Operation 19
Check Points for Preset and Pattern Function before Operation 19
OSD Menu 20
Reserved Preset (Hot Keys) 20
Preset 21
Swing 21
Pattern 22
Group 23
Other Functions 23
OSD Display 25
④OSD Menu
Quick Programming Guide 26
Main Menu 26
Display Setup 27
Privacy Zone Mask Setup 28
Camera Setup 30
Motion Setup 35
Preset Setup 38
Swing Setup 40
Pattern Setup 41
Group Setup 42
System Initialize 45
⑤Specifications 46
Dimension 50
TABLE OF CONTENTS

Powerful Zoom Camera & Setup Options
Image Sensor : 1/4" Interline Transfer CCD (ASD276, ASD376)
Zoom : x27 Optical Zoom, x16 Digital Zoom (ASD276)
x37 Optical Zoom, x16 Digital Zoom (ASD376)
Day & Night, Privacy Mask and HLC
SNR (Super Noise Reduction) Function
Various Focus Modes : Auto-Focus, Manual Focus, Semi-Auto Focus
Various Setup Options via OSD Menu.
Powerful Pan/Tilt Functions
MAX. 360˚/sec High Speed Pan/Tilt Motion
With the Vector Drive Technology, Pan/Tilt motions are accomplished along the
shortest path. As a result, the time to the target view is remarkably short and the video
on the monitor is very natural in monitoring mode.
With our Micro-Stepping Control Technology, the video looks very natural at high
zoom magnification, during a jog operation on a controller, as the camera can be
controlled at 0.05˚/sec. Hence it is very easy to make the camera focus on desired
target views at high zoom magnification. Additionally it is easy to make the camera
focus at the desired positions with zoom-proportional pan and tilt movements.
Preset, Pattern, Swing, Group, Privacy Masking and More…
MAX. 127 Presets are programmable and each preset can have its own parameter
values independently from the other presets.
For an example, refer to the below table.
PresetNo. WhiteBalance AutoExposure ••• Label Remarks
Preset 1 CaseA Case3 “ENTRANCE”
Preset 2 CaseC Case5 “WAREHOUSE”
Preset 3 CaseV Case 2 “OFFICE”
•••
Preset95 ReservedforOSD Menu
•••
Preset 128 CaseK Case9 “TERRACE”
ㅡ ㅡ ㅡ ㅡ
Speed Dome Camera Instruction Manual 6/50
Features
INTRODUCTION 1

Speed Dome Camera Instruction Manual 7/50
MAX. 8 sets of Swing are programmable. This function means the camera moves
repetitively between two preset positions at programmed speeds.
MAX. 4 Patterns are programmable. With this function the camera memorises the
path (mostly curve path) created by the joystick of a controller and then mimics
the joystick movements as closely as possible.
MAX. 8 sets of Group are programmable. This function means the camera memorises
acombination of Presets, Pattern and/or Swings sequentially and runs the Presets,
Patterns and/or Swings repetitively. A Group can contain up to 20 functions,any of
which are Preset/Pattern/Swing.
MAX. 8 Privacy Masks are programmable, to protect other’s privacy.
PTZ(Pan/Tilt/Zoom) Control
With the RS-485 communication connection, a MAX. 255 units of camera can
be connected to a single controller.
Pelco-D or Pelco-P protocol can be selected as the control protocol in the current
firmware version.
OSD(On Screen Display) Menu
OSD menu is provided to display the status of camera and to configure the functions
interactively.
Information,such as,Camera ID, Pan/Tilt Angle, Direction, Alarm Input and Preset
are displayed on screen.
Alarm In/Out Function (only for models which have I/O function)
3 alarm sensor inputs and 1 alarm sensor outputs are available.
Alarm sensor input is decoupled with photo-couplers to avoid external electrical
noise and shock.
Both N.O. (Normally Open) and N.C. (Normally Closed) sensors can be used,and
the signal range of the sensor input is from DC5V to 12V for various applications.
The camera can be set to move to a Preset position or to run functions such as Pattern,
Swing and Group when there are external sensor activations. Also,a Post Alarm
functionsis possible, which is designed to activate after a user-defined time period
and sequentially in succession to the action by an external sensor activation.
Reserved Presets (Hot Keys)
Most camera setup options are easily set up using the reserved presets (Hot Keys),
without entering into the OSD menu. For more information, refer to the
"Reserved Presets (Hot Keys)"in this manual.
INTRODUCTION 1

Speed Dome Camera Instruction Manual 8/50
Network Function (only for IP addressable models)
Network functions including remote monitoring, bi-directional audio and others
are available through IP based networkssuch as LAN, ADSL/VDSL, and Wireless.
For more information, refer to the separate manual for IP Addressable models.
Outdoor Environmental Compatibility and Easy Installation
Fans and heaters are built-in to the camera for cold and hot temperature
environments. The mechanical design protects the camera from water ingress
and dust (to IP66 when installed properly using the correct manufacturers bracket).
Only for outdoor models.
It is easy to install this camera.
INTRODUCTION 1

Speed Dome Camera Instruction Manual 9/50
Package Components
Product & Accessories
Main Body & Surface MountBracket Default Accessories
[Main Cable,Wrench]
Accessories for models with Alarm In/Out
Function[I/OCable]
Accessoriesfor IP Addressable models
[CrossoverLAN Cable,Audio Cable,CD]
Brackets (Optional)
Wall Mount Bracket
[Screws:Machine M5×15,HexLag #14×50]
CeilingMountBracket
[Screws:Machine M5×15,AnchorBolt 3/8"×70]
INTRODUCTION 1

Speed Dome Camera Instruction Manual 10/50
Main Part Description
DIP Switch
Dome Cover
Sensor I/O Port (I/O Model)
Main Connector
Audio Port (IP Model)
LAN Port (IP Model)
Reset Switch (IP Model)
Mounting Hook Mounting Screw Holes
Dome Cover Do not detach the protective vinyl from the dome cover before
completing the installation process.This protectsthe dome cover
from scratches and dust.
DIP Switch Used to set up camera ID and protocol.
MountingHook Used to assemble the main body with a wall or ceiling mount
bracket. Insert the mounting hooks into the holes on the surface
of the main body and turn the main body.
MountingScrew Hole Used to assemble the main body to a bracket.
Main Connector Used for power wiring, the video cable and the RS-485
communication cable connections.
SensorI/O Port Used for the sensor In/Out connections ( sensor I/O function
models only)
LAN Port Used for the Ethernet connection (IP addressable models only)
Audio Port Used for the Audio In/Out connection (IP addressable models only)
Reset Switch Used to reset all the network configurations to the factory
defaults(IP addressable models only).Press the button for more
than 5 seconds to reset the network system.
INTRODUCTION 1

Speed Dome Camera Instruction Manual 11/50
DIP Switch Setup
Before installing the camera, set up the DIP switch to configure the camera ID and the
communication protocol.
Camera ID Setup
ON
ON
1 2 3 4 5 6 7 8
ID numbers of cameras are set up with binary numbers.
See the examples shown below.
Pin 1 2 3 4 5 6 7 8
BinaryValue 1 2 4 8 16 32 64 128
example ID=5 on off on off off off off off
example ID=10 off on off on off off off off
The camera ID range is “1~255”. Camera ID must not be
“0”!
The factory default of the camera ID is “1”.
Match the camera ID with the Cam ID setting of the DVR
or Keyboard Controller to control the camera.
If you are connecting a single camera to a controller,
terminate the camera. When connecting more than one
camera to a single controller, terminate the last camera on
the communication line. The last camera means the camera
farthest in cable length from the controller.
Note that the total length of the communication cable
between a controller and the camera(s) on the same
communication line must be less than 1.2Km.
INSTALLATION 2

Speed Dome Camera Instruction Manual 12/50
Communication Protocol Setup
1 2 3 4
ON
ON
Select an appropriate Protocol with the DIP switch combination.
Switch Mode
P0
(Pin 1) P1 (Pin 2) P2 (Pin 3)
Protocol
OFF OFF OFF PELCO-D, 2400 bps
ON OFF OFF PELCO-D, 9600 bps
OFF ON OFF PELCO-P, 4800 bps
ON ON OFF PELCO-P, 9600 bps
devreseRsrehtO
Match the camera protocol with the camera protocol setting of
your DVR or keyboard controller to control the camera.
Turn the camera OFF to adjust the DIP switch. If you camera protocol
is changed while the power is still applied the change is only effective
after rebooting the camera.
The factory default protocol is “Pelco-D, 2400 bps”.
INSTALLATION 2

Speed Dome Camera Instruction Manual 13/50
Terminal Resistor Set-up
1 2 3 4
ON
ON
The terminal resistor is used in the following cases.
Case 1 : In cases where the control cable between a camera and
a controller is very long (1:1 connection)
If the communication cable length is very long, the electrical signal can
bounce at the termination point. This reflected signal causes distortion
of the original signal and the camera can go out of control. In this
case, the terminal resistor on both sides i.e. camera and controller
should be set to ‘ON’.
Case 2 : In caseswhere multiple cameras are connected to
a controller.
For similar reasons to the above, the terminal resister of the
controller and last camera should be set to ‘ON. The last camera means
the camera farthest in cable length from the controller. Do not turn
on the terminal resistor of all the cameras on the same
communication cable.
Controller
n#2#1#
Terminal Resistor ON
RS-485
Terminal Resistor
OFF
Terminal Resistor
OFF
Terminal Resistor
ON
INSTALLATION 2

Speed Dome Camera Instruction Manual 14/50
Installation with Ceiling Mount Bracket
①Remove the ceiling tile from the ceiling
and cut a hole whose diameter is
30~40mm in the ceiling tile to pass the
wire(s) and cable(s) through to the upside
of the ceiling (in case of the wiring and
cabling through the mounting surface
only).Then prepare the ceiling mount
bracket. Pull the wire(s) for the system as
below (Anchor Bolt 3/8"×70).
②Pull the wire(s) and cable(s) for the
system as below. Wire the cable(s) to the
ports. Insert the mounting hooks into the
holes on the surface of the main body and
turn the main body. Assemble the main
body with the camera mount adaptor and
the 3 screws. (Machine M5×15)
③Screw the dome cover to the main body
and remove the protective vinyl from the
dome cover.
Important Notice
Beforestarting the installation,makesurethattheCamera ID and Protocol are set up properly.
To adjust the installation height from the mounting surface,apole and coupler could be needed
between the surface mount part of the ceiling mount bracket and the camera mount part of the ceiling
mount bracket. Note that these are not suppliedby the manufacturer.
INSTALLATION 2

Speed Dome Camera Instruction Manual 15/50
Installation with Wall Mount Bracket
①Make a hole whose diameter is 30~40mm
on the mounting surface to pass the
wire(s) and cable(s) through the mounting
surface (in case of the wiring and cabling
through the mounting surface only).Then
prepare the wall mount bracket. Pull the
wire(s) and cable(s) for the system as
below. Attach the wall mount bracket to
the mounting surface. (Hex Lag #14×50)
②Pull the wire(s) and cable(s) for the
system as below. Wire the cable(s) to the
ports. Insert the mounting hooks into the
holes on the surface of the main body and
turn the main body. Assemble the main
body with the camera mount adaptor and
the 3 screws. (Machine M5×15)
③Screw the dome cover to the main body
and remove the protective vinyl from the
dome cover.
Important Notice
Beforestarting the installation,makesurethattheCamera ID and Protocol are set up properly.
INSTALLATION 2

Speed Dome Camera Instruction Manual 16/50
Wiring and Cabling
RS-485
BNC
SENSOR I/O
LAN CABLE
AUDIO
CABLE
MAIN CABLE
I/O CABLE
BROWSER
POWER
MONITOR
CONTROLLER / DVR
MIC SPEAKER
IR
SENSOR
DOOR
SWITCH
INTERNET
Port Description
Main Cable
Port Pin Number (RJ45) Connector / Wire Colour Signal
+oediV1
2,4 BNC Connector Video −
+584-SRdeR5
584-SRwolleY3 −
+rewoPegnarO7
rewoPetihW8,6 −
I/O Cable
Port Pin Number (RJ25) Wire Colour Signal
+MOCNIeulB1
1NIwolleY2 −
2NIneerG3 −
3NIdeR4 −
ATUOkcalB5
BTUOetihW6
Audio Cable
Port Pin Number Connector / Wire Colour Signal
1 RCA (Yellow) Audio IN
DNGoiduA2
3 RCA (White) Audio OUT
INSTALLATION 2

Model InputVoltage Range Current Consumption
A5.2
DC12V Model DC 11V ~ 18V
AC24V Model AC 17V ~ 29V 1.5A
Speed Dome Camera Instruction Manual 17/50
Power Description
Carefully check the voltage and current capacity of the rated power. The rated power is
indicated on the back of the main unit.
For the DC input models, be careful with the polarity of DC power. The system could be
permanently damaged by incorrect DC input.
In cases where the length of the power wire is very long, there'll be a voltage drop and
the system may not work properly. Power cable length must be as short as possible.
RS-485 Communication
For PTZ control, connect the cable(s) to the keyboard or DVR. To connect multiple
cameras to a single controller, RS-485 communication should be connected in parallel
as shown below. When connecting a single camera to a controller, terminate the
camera. When connecting more than one camera to a single controller, terminate the
last camera on the communication line. The last camera means the camera farthest in
cable length from the controller. Note that the total length of the communication cable
between a controller and the camera(s) on the same communication line must be less
than 1.2Km.
INSTALLATION 2
CONTROLLER / DVR
RS-485
+
-
#1
+
-
#2
+
-
#n
+
-

Speed Dome Camera Instruction Manual 18/50
Video
Use BNC coaxial cable, or Category 5e/6 with a balun (e.g. GTP002S).
Alarm Input
Before connecting any sensors, check the drivevoltages and the output signal types.
Output signal types for sensors are generally divided into Open Collector and
Voltage Output type.The wiring must be correct, according to the type of sensor
being connected.
Signal Description
IN COM+ The electric power source to drive input circuit. Connect the (+) wire of electric
power source to drive the Sensors to this port,as shown on the abovecircuit.
IN1 -,IN2 -,IN3 - Connect the outputs of sensors to each port as shown on the above
circuit.
If Alarm Inputs are required, the sensors types must be selected in OSD menu. The
sensor types are divided into Normally Open and Normally Closed. If the wrong sensor
types are selected, alarms will be activated in reverse to the sensor inputs.
Normal Open Output Voltage is in a high state when the sensor is activated
Normal Close Output Voltage is in a high state when the sensor is not activated
Relay Output
Internal
OUT 1
AC or DC
LOAD
The maximum loads are as follows.
rewoPCArewoPCDepyTrewoP
Maximum Load MAX. DC 24V, 1A MAX. AC 125V, 0.5A
IN COM+ +5V~12V
IN 1-
IN 3- +
+
-
-
+
-
Internal
Sensor 1
Sensor 3
INSTALLATION 2

Speed Dome Camera Instruction Manual 19/50
Check Points before Operation
Before turning on the system, check that the wire(s) and cable(s) are properly connected.
Check if the camera ID on the controller is properly selected. The camera ID must be
identical to that of the target camera. The camera ID can be checked by reading the DIP
switch of the camera or on the OSD.
If your controller supports multi-protocols, the protocol must be changed to match to that of
the camera.
Adjust the DIP switch after turning off the camera. If the camera protocol is changed when
the power is still applied, the change is only effective after rebooting the camera.
Since operation methodscan be different by controllers, refer to your controller manual
if the camera cannot be controlled properly. The operation of this manual is based on the
standard Pelco® Controller.
Check Points for Preset and Pattern Function before Operation
Check fully, in advance, how to operate the preset and pattern function on your controller
or DVR.
Refer to the following table when using standard Pelco® protocol controllers.
< Go Preset > Input [Preset Number]andpress [Preset] button shortly.
< Set Preset > Input [Preset Number]and keep pressing[Preset]button formore than 2 seconds.
< Run Pattern > Input [PatternNumber] and press[Pattern] button shortly.
< Set Pattern > Input [PatternNumber]andkeep pressing [Pattern] button for more than 2 seconds.
If your controller or DVR has no pattern button or function, use the Hot Keys with preset
numbers. For more information, refer to “Reserved Presets(Hot Keys)” in this manual.
OPERATION 3

Speed Dome Camera Instruction Manual 20/50
OSD Menu
Function With OSD menu, the system can be properly configured for each
application.
Entering into OSD Go Preset [95]
Reserved Presets (Hot Keys)
Description Some Preset numbers are reserved to change some parameters without entering into
OSD menu.
Hot Keys Go Preset [95] :Entering into OSD menu
Go Preset [131~134] :Running PatternFunction 1~4
Go Preset [141~148] :Running Swing Function1 ~ 8
Go Preset [151~158] :Running Group Function 1 ~8
Go Preset[161] :Turningoff Relay Output
Set Preset [161] :Turningon Relay Output
Go Preset [167] :SettingZoomProportional Function toON
Set Preset [167] :Setting ZoomProportionalFunction to OFF
Go Preset [170] :SettingCamera BLC Mode to OFF
Go Preset [171] :SettingCamera BLC Mode to ON
Go Preset[174] :SettingCamera Focus Mode to AUTO
Go Preset[175] :Setting CameraFocusMode to Manual
Go Preset[176] :SettingCamera Focus Mode to SEMI-AUTO
Go Preset [177] :SettingDay & Night Mode to AUTO
Go Preset [178] :SettingDay & Night Mode to NIGHT
Go Preset[179] :SettingDay& Night Modeto DAY
Go Preset [190] :Setting OSDDisplay Modeto AUTO (ExceptPrivacy Mask)
Go Preset [191] :Setting OSDDisplay Mode to OFF (Except Privacy Mask)
Go Preset [192] :Setting OSDDisplay Modeto ON (Except Privacy Mask)
Go Preset[193] :Setting allPrivacy Mask Displayto OFF
Go Preset[194] :Setting allPrivacyMaskDisplaytoON
OPERATION 3