Genie GHDPIR User manual

Quick Start Guide
Please read these instructions carefully before operating the unit
and keep for further reference.
2.1MP AHD Operational PIR
Camera
GHDPIR

Contents
ii
1.0 Introduction..........................................................................................................3
1.1 Product Features...........................................................................................3
1.2 Product Overview ........................................................................................3
1.3 Specification.................................................................................................4
1.4 Choosing an Installation Location ...............................................................4
2.0 Detector Installation............................................................................................5
2.1 Detector Installation.....................................................................................5
2.2 Installation Options .....................................................................................6
2.3 Camera Module Connection .......................................................................6
2.4 Detector Connection ..................................................................................7
2.5 Setting up the Detector ..............................................................................7
3.0 Potentiometers Adjustment ................................................................................8
4.0 Testing The Detector...........................................................................................9
5.0 Video Synchronisation.........................................................................................10

3
Please read this instruction carefully before operating the product and keep it for further
reference. All examples and pictures used here are for reference only.
The contents of this manual are subject to change without notice.
The Genie GHDPIR is a 2.1MP AHD 3.7mm lens camera built into a fully operational PIR
detector housing. Suitable for covert and discreet operations.
1.1 Product Features
• Sony 1/2.9” 2.19MP Progressive Scan CMOS
• 1080p (1920×1080) @ 30 (25)fps
• 4-in-1 output (AVI, TVI, CVI, CVBS)
• Fixed Board Lens
• Mechanical Day&Night
• WDR, 3D DNR, Defog
• UTC function supports OSD Control
• Camera module
• Conical pinhole lens
• Quad pyro sensor
• Bi-directional temperature compensation
• Pet immunity up to 25Kg. Pet active below 1M
• Tamper switch
• NDAA compliant
1.2 Product Overview
1.0 Introduction

Quick Start Guide 2.1MP AHD Operational PIR Camera
4
1.3 Specification
1.4 Choosing an Installation Location
Camera
Image Sensor 1/2.9” Progressive Scan CMOS
Resolution
TVI, AVI, CVI : 1080p @ 30(25)fps / 720p @ 60fps (50fps) /
720p @ 30fps (25fps)
TV out : CVBS NTSC/PAL
Minimum Illumination 0.2Lux(F1.6, AGC33dB, DSS:x2)
Lens Conical Pinhole Fixed Board Lens, 3.6mm, F 2.0
Angle of View 106.9˚ (D)x89.7˚ (H)x47.5˚ (V)
Shutter Speed AUTO/FLICKER/MANUAL/(1/30(25)~1/30,000)
Digital Slow Shutter (DSS) OFF~ x32
Effective Pixel 1985(H) x 1105(V)
Video Output AVI, TVI, CVI, CVBS
Functions
White Balance AUTO/AUTO EXT/PUSH LOCK/MANUAL
WDR/BLC OFF/BLC/HLC/WDR (4 Zones selectable)
D-WDR OFF/LOW/MIDDLE/HIGH
Level 132.6dB
Auto Gain Control (AGC) OFF~45dB
Day & Night AUTO/COLOUR/B&W (Electronic D&N)
Noise Deduction 3D-DNR(OFF/LOW/MIDDLE/HIGH)
Motion Detection OFF/ON(4 Zones)
Privacy Mask 16 Zones
Image Rotation OFF/H-FLIP/V-FLIP/HV-FLIP
Defog OFF/ON (AUTO/MANUAL)
Sharpness 0~10
OSD Control UTC
Language 8 languages
Others
Power Supply DC12V(±10%)
Power Consumption Max.140mA @ DC12V
Temperature Conditions Operating: -10°C~+50°C
Storage: -20°C~+60°C
Choose a location most likely to intercept an
intruder. (Our recommendation is a corner
installation). See detection pattern on the
right.
The quad-element high quality sensor detects
motion crossing the beam; it is slightly
less sensitive detecting motion toward the
detector.
The GHDPIR performs best when provided
with a constant and stable environment and
background.
Avoid the following locations:
• Facing direct sunlight.
• Facing areas that may change
temperature rapidly.
• Areas where there are air ducts or
substantial airflows.

5
2.1 Detector Installation
The detector can either be wall, corner or ceiling mounted by using a special bracket base
for the bracket mounting.
1. To remove the front cover, unscrew the holding screw and gently raise the front cover.
2. Insert wire through the bracket and holes “A” and “B”.
3. Mount the bracket base to the wall or to the ceiling with the suitable adaptor. Hold the
detector base in front of the protected area and tighten the bracket screw.
4. Insert the wires through the bracket and connect the wires to the terminal block.
5. Replace the cover by inserting it back in the appropriate closing pins and screw in the
holding screw.
2.0 Detector Installation
Unscrew the
holding
screw and
open base
Wire Size Requirements
Use #22 AWG (0.5 mm) or wires with a larger diameter.
Use the following table to determine the required wire
gauge (diameter) depending on the length of wire
between the detector and the control panel.

Quick Start Guide 2.1MP AHD Operational PIR Camera
6
2.2 Installation Options
2.3 Camera Module Connection
Connect the camera module to the main PCB.
Ceiling Bracket Base Wall Bracket Base

Quick Start Guide 2.1MP AHD Operational PIR Camera
7
2.4 Detector Connection
Please refer to “Wire Size Requirements” in 2.1 Detector Installation before connecting detector to achieve
optimal operation.
2.5 Setting up the Detector
Block Connector
Camera Input
Audio Sensitivity Adjustment
Pyrosensor
Tamper
PIR
Sensitivity
Adjustment
Switch For
Settings

8
3.0 Potentiometers Adjustment
There two potentiometers located on the PCB device to set the optimal sensitivity of the
detection and the audio.
PIR Sensitivity Adjustment
• Use the Potentiometer marked “PIR” to adjust the detection sensitivity between 15%
and 100% according to walk test in the protected area. (Factory setting to 57%).
• Rotate the potentiometer clockwise to increase range, counter-clockwise to decrease
range.
Audio Sensitivity Adjustment
• Use the potentiometer “AUDIO” to adjust the audio sensitivity.
• Rotate the potentiometer clockwise to increase sensitivity.
• Rotate the potentiometer counter-clockwise to decrease sensitivity.

9
4.0 Testing The Detector
Wait one minute after applying power and warm up time.
Conduct testing with the protected area cleared of all people.
Walk Test
1. Remove front cover.
2. Set LED to ON position.
3. Reassemble the front cover.
4. Start walking slowly across the detection zone.
5. Observe that the LED lights whenever motion is detected.
6. Allow 5 sec. between each test for the detector to stabilise.
7. After the walk test is completed, you can set the LED to OFF position.
NOTE:
Walk tests should be conducted, at least once a year, to verify proper operation of the
detector.

10
5.0 Video Synchronisation
The video module has the ability to Auto Detect the DVR or Screen which it is connected.
In case of the video is not transmitted, please perform a reset by following steps according
to your DVR model:
1. For CVBS: Push the OSD button to LEFT for 5 to 10 seconds. The camera automatically
turn OFF and ON. Then you will see the analogue CVBS mode.
2. For AHD to TVI / TVI to AHD: Cursor on EXPOSURE -> RIGHT RIGHT RIGHT (3 times) then
ENTER. -> You will see the system in the hidden menu.
3. For PAL & NTSC: It is in the OSD menu. ADJUST -> VIDEO OUT

Sales [phone]
Enquiries [email protected]o.uk
Website www.genieproducts.co.uk