Genie HDC222 User manual

User Manual
Please read these instructions carefully before operating the unit
and keep for further reference.
2.1MP HD-SDI Box Camera
HDC222

ii
Intro Section
Please read this instruction carefully before operating the product and keep it for
further reference. All examples and pictures used here are for reference only.
The contents of this manual are subject to change without notice.
CAUTION:
• A regulated DC12V 500mA power supply is recommended for use with this
camera to ensure the best picture quality and stable operation. An unregulated
power supply may cause damage to the camera. Using an unregulated power
supply will void the product warranty.
• It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to high
impedance, then please adjust accordingly.
• Do not attempt to disassemble the camera to access internal components.
Refer servicing to your distributor or manufacturer.
• Never face the camera towards the sun or any bright or reflective light, which
may cause smear on the picture and possible damage to the image sensor.
• Do not remove the serial sticker for the warranty service.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
• To help prevent electric shock, plug the equipment and peripheral power
cables into properly polarised or grounded electrical outlets. These cables are
equipped with the wide blade or the third prong to ensure proper grounding.
Do not use adapter plugs or remove the grounding prong from a cable. If the
provided plug does not fit your outlet, consult an electrician.
• Ensure that nothing rests on your equipment’s cables and that the cables are
not located where they can be stepped on, tripped over, or pinched.
• Only use attachments or accessories as specified
• Only use the equipment with the cart, stand, tripod, bracket,
• or table that is specified by the manufacturer or sold with the
• apparatus. When a cart is used, use caution to prevent the cart
• from tipping over and to avoid injury.
• Do not connect or disconnect during lightning storms due to risk of electric
shock.
• If any of the following conditions occur, unplug the equipment from the
electrical outlet and replace the part or contact your trained service provider:
– The power cable, extension cable, or plug is damaged.
– An object has fallen into the equipment.
– The equipment has been exposed to water.
– The equipment has been dropped or damaged.
– The equipment does not operate correctly when you follow the operating
instructions.

Contents
iii
1.0 Introduction..........................................................................................................4
1.1 Product Features...........................................................................................4
1.2 Product Dimensions.....................................................................................4
1.3 Components.................................................................................................4
1.4 Mounting Position ........................................................................................4
1.5 Specification ................................................................................................5
2.0 Installation ...........................................................................................................6
2.1 Monitor Connection .....................................................................................6
2.2 RS-485 Type.................................................................................................6
3.0 OSD Manual..........................................................................................................7
3.1 Function Description....................................................................................8
4.0 RS-485..................................................................................................................11
NOTE:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

4
The Genie HDC222 is a 2.1MP HD-SDI box camera with a 6-in1 output (AVI, TVI, CVI,
EX-SDI, HD-SDI and CVBS).
1.1 Product Features
• Sony 1/2.8” 2.13MP Progressive Scan SONY Starvis CMOS
• 1080p (1920 × 1080) @ 30(25)fps
• 6-in-1 output (AVI, TVI, CVI, EX-SDI, HD-SDI, CVBS)
• C/CS Mount for lens
• Mechanical Day & Night
• WDR, 3D DNR, Defog
• UCC, UTC function supports OSD Control
1.2 Product Dimensions
1.3 Components
• Camera
• C-Mount Adapter Ring
• User Manual
1.0 Introduction
70.5mm
58mm
58mm

User Manual 2.1MP HD-SDI Box Camera
5
1.4 Specification
Camera
Image Sensor 1/2.8” Progressive Scan SONY Starvis CMOS
Resolution
HD-SDI / EX-SDI1.0 / EX-SDI2.0 / AVI /TVI / CVI : 1080p @
30fps (25fps)/ 720p @ 60fps(50fps) / 720p @ 30fps (25fps)
TV out : CVBS NTSC / PAL
Electronic Shutter AUTO / FLICKER / MANUAL /(1/30(25)~1/30,000)
Digital Slow Shutter (DSS) OFF~ x32
Minimum Illumination 0.03Lux (F1.2, ICR OFF, AGC33dB, DSS:x2)
Lens C/CS Mount lens, depends on lens
Effective Pixels 1945(H) x 1097(V)
Functions
White Balance AUTO / AUTO EXT / PUSH LOCK /MANUAL
WDR/BLC OFF / BLC / HLC / WDR15P / WDR30P (4 Zones selectable)
Auto Gain Control
(AGC) OFF~45dB
Day & Night AUTO / COLOUR / B&W (Electronic D&N)
Noise Deduction 3D-DNR (OFF / LOW / MIDDLE /HIGH)
Motion Detection OFF / ON (4 Zones)
Privacy Mask 16 Zones
Image Rotation OFF / H-FLIP / V-FLIP / HV-FLIP
Defog OFF / ON (AUTO/MANUAL)
Sharpness 0~10
Language 8 languages
Video Output HD-SDI / EX-SDI1.0 / EX-SDI2.0 / AVI / CVI / TVI / CVBS
Others
Operating Temperature -10°C~+50°C
Storage Temperature -20°C~+60°C
Power Source 12VDC (±10%)
Power Consumption Max.130mA @ 12VDC
Dimension 58 × 58 × 70.5 mm
Weight 180g

6
2.0 Overview & Function
AC24V / DC12VDC12V
TRIPOD MOUNTING HOLE(1/4"-20 UNC)
C-MOUNT ADAPTOR RING
LENS MOUNT COVER
CS-MOUNT ADAPTOR RING
CS-MOUNT ADAPTOR RING
LOCKING SCREW(2EA)
AUTO IRIS JACK
TRIPOD MOUNTING HOLE(1/4"-20 UNC)
1. MENU BUTTON
2. UP BUTTON
3. DOWN BUTTON
4. LEFT BUTTON
5. RIGHT BUTTON
6. EX-SDI (HD-SDI / EX-SDI 1.0 / EX-SDI 2.0), HD(AVI / TVI / CVI / CVBS) SELECT
SWITCH
7. POWER LED (The LED turns on when power is supplied)
8. VIDEO OUT JACK(AVI / TVI / CVI / CVBS / HD-SDI / EX-SDI 1.0 / EX-SDI 2.0)
(By setting, video signal is changed)
(Used to connect an external video monitor or DVR in jack)
9. VIDEO OUT JACK (CVBS)
(Used to connect an external video monitor or DVR in jack)
10. POWER TERMINAL
(Used to connect an DC12V power source)
(Options : AC24V / DC12V

7
3.0 Installation
Replace the auto iris lens connection plug cover and take off the Sensor protection cap.
Then, attach the auto iris lens to the camera by screwing it in clockwise.
Insert the connection plug that is connected to the auto iris lens cable into the auto iris lens
connector, located on the side of the camera.
NOTE:
Use only lenses within the specifications shown below.
Otherwise, lenses may damage the camera or abnormal fixing may result.
C-mount lens : 10 mm or less
CS-mount lens : 5 mm or less
Installation of C-Mount Lenses
Installation of CS-Mount Lens
CS-MOUNT ADAPTOR RING
C-MOUNT ADAPTOR RING
CS-MOUNT ADAPTOR RING

8
Monitor Connection
DC12V
24VAC/12VDC
CAUTION : After installation, turn off the power and turn it back on.
4.0 Connections

9
5.0 OSD
Menu Structure

User Manual 2.1MP HD-SDI Box Camera
10

User Manual 2.1MP HD-SDI Box Camera
11
(*1) WDR 15P : 3DNR on, 2DNR on, 15 Frame Rate
WDR 30P : 3DNR off, 2DNR on, 30 Frame Rate
The WDR function is not available in the CVBS output.
(*2) The 720/60(50)p mode is not real 60(50) Frame rate because 720/30(25)p
scenes are output twice.
(*3) ‘APPLY’ menu must be selected for changing FRAME RATE, SDI OUT and
ANALOG OUT.
(*4) It is recommeded to select DVR maker in the menu according to DVR in use.
(*5) Value in SYSTEM menu (FRAME RATE, SDI OUT, ANALOG OUT, DVR, LANGUAGE)
is not initialised by
FACTORY DEF or INITIAL selection.
Important Note : Setting value changing is available by EXIT meniu selection.

User Manual 2.1MP HD-SDI Box Camera
12
Hidden Menu
• CONVERT ANALOG OUTPUT MODE
STEP 1. ENTER
Press UP/DOWN/LEFT/RIGHT key more than 2 sec.
SETP 2. SELECT
Press UP key more than 5 sec : AVI
Press DOWN key more than 5 sec : CVI
Press LEFT key more than 5 sec : CVBS
Press RIGHT key more than 5 sec : TVI
STEP 3. CONFIRM
If the ‘YES’ is not checked within 30sec, the value returns to the previous setting.
• CONVERT SDI OUTPUT MODE
STEP 1. ENTER
Press UP/DOWN/LEFT/RIGHT key 3 times.
SETP 2. SELECT
Press DOWN key 5 times : EX-SDI 2.0
Press LEFT key 5 times : HD-SDI
Press RIGHT key 5 times : EX-SDI 1.0
STEP 3. CONFIRM
If the ‘YES’ is not checked within 30sec, the value returns to the previous setting.

Sales [phone]
Enquiries [email protected]o.uk
Website www.genieproducts.co.uk