Genie GIPPIR User manual

Quick Start Guide
Please read these instructions carefully before operating the unit
and keep for further reference.
2MP H.264 Dual Stream IP
Operational PIR Camera
GIPPIR

Contents
ii
1.0 Introduction..........................................................................................................3
1.1 Product Features...........................................................................................3
1.2 Product Overview ........................................................................................3
1.3 Specification.................................................................................................4
1.4 Choosing an Installation Location ...............................................................4
2.0 Detector Installation............................................................................................5
2.1 Detector Installation.....................................................................................5
2.2 Installation Options .....................................................................................6
2.3 Camera Module Connection .......................................................................6
2.4 Detector Connection ..................................................................................7
2.5 Setting up the Detector ..............................................................................7
3.0 Potentiometers Adjustment ................................................................................8
4.0 Testing The Detector...........................................................................................9

3
1.0 Introduction
Please read this instruction carefully before operating the product and keep it for further
reference. All examples and pictures used here are for reference only.
The contents of this manual are subject to change without notice.
The Genie GIPPIR is a fully operational grade 2 PIR with a 2MP full HD H.264 IP camera
pre installed. The camera is supplied with a 3.7mm conical pinhole lens and can be
powered with either a DC12V or a PoE (802.3af) switch / injector.
1.1 Product Features
• Full HD (1080p) IP Network board
• 1/ 2.8” 2MP progressive CMOS sensor
• H.264 / MJPEG dual streaming
• Minimum illumination: 0.1 Lux (Colour)
• WDR, D&N, AGC, BLC, HLC, DNR, Sens-Up
• 32×32 one IP board (Video only)
• Motion detection / privacy zone
• Optional 32×32 sub board for audio & alarm
• DC12V, external PoE Quad pyro sensor
• Bi-directional temperature compensation
• Pet immunity up to 25Kg. Pet active below 1M
• Tamper switch
• NDAA compliant
1.2 Product Overview

Quick Start Guide 2MP H.264 Dual Stream IP Operational PIR Camera
4
1.3 Specification
1.4 Choosing an Installation Location
Choose a location most likely to intercept an
intruder. (Our recommendation is a corner
installation). See detection pattern on the
right.
The quad-element high quality sensor detects
motion crossing the beam; it is slightly
less sensitive detecting motion toward the
detector.
The GIPPIR performs best when provided
with a constant and stable environment and
background.
Avoid the following locations:
• Facing direct sunlight.
• Facing areas that may change
temperature rapidly.
• Areas where there are air ducts or
substantial airflows.
Camera
Image Sensor 1/2.8” Progressive Scan CMOS Sensor (Sony IMX307)
Effective Pixels 1920 (H) x 1080 (V) Approx. 2.13M pixels
Minimum Illumination Colour Mode: 0.1 Lux, B&W Mode: 0.01 Lux
Lens Type 3.7mm conical pinhole lens, M12 board lens
(2.8mm, 3.6mm, 4.3mm, 6mm, 8mm)
Shutter Speed 1/25 ~ 30,000sec
Motion Detection Yes (4 areas)
Privacy Zone Yes (4 areas)
Image Enhancement AE, AWB, WDR, DNR, AGC, Brightness, Contrast, Stabilisation,
Sharpness, Day & Night, Sens-Up, BLC, HLC
Video
Video Compression H.264 (Baseline/Main Profile), MJPEG
Streaming (Dual) Primary (H.264) : Max. 1920 × 1080,
Secondary (H.264 or MJPEG) : Max. 800 × 600
Resolution and Frame Rate
Primary (H.264) : 25fps @ 1080p, 720p, 800 × 600, 640 × 480,
320 × 240
Secondary (H.264 or MJPEG) : 25fps @ 800 × 600, 640 × 480,
320 × 240
Bit Rate / Control 512Kbps ~ 10Mbps / CBR, VBR
Sub Board
(Option)
Audio G.711 Compression, 2 way audio (MIC In / Spk Out, line level)
Alarm DI/DO (Alarm In, Relay Out)
Interface Ethernet 10/100-Base-T Ethernet (Auto-Sensing)
Network
Support Protocol TCP/IP, UDP, IPv4, HTTP, DNS, NTP, IGMP, RTP/RTSP, DHCP,
WS-Discovery, Onvif Profile S compatible
3rd Party Integration Onvif Profile S 2.4, CGI
Login Authority Administrator, Operator, Viewer
Maximum Streaming User 4
Others
Operating Temperature -10°C ~ +50°C
Operating Humidity 0~80% (Non-condensing)
Power Source DC12V/1.6W

5
2.1 Detector Installation
The detector can either be wall, corner or ceiling mounted by using a special bracket base
for the bracket mounting.
1. To remove the front cover, unscrew the holding screw and gently raise the front cover.
2. Insert wire through the bracket and holes “A” and “B”.
3. Mount the bracket base to the wall or to the ceiling with the suitable adaptor. Hold the
detector base in front of the protected area and tighten the bracket screw.
4. Insert the wires through the bracket and connect the wires to the terminal block.
5. Replace the cover by inserting it back in the appropriate closing pins and screw in the
holding screw.
2.0 Detector Installation
Unscrew the
holding
screw and
open base
Wire Size Requirements
Use #22 AWG (0.5 mm) or wires with a larger diameter.
Use the following table to determine the required wire
gauge (diameter) depending on the length of wire
between the detector and the control panel.

Quick Start Guide 2MP H.264 Dual Stream IP Operational PIR Camera
6
2.2 Installation Options
2.3 Camera Module Connection
Connect the camera module to the main PCB.
Ceiling Bracket Base Wall Bracket Base

Quick Start Guide 2MP H.264 Dual Stream IP Operational PIR Camera
7
2.4 Detector Connection
Please refer to “Wire Size Requirements” in 2.1 Detector Installation before connecting detector to achieve
optimal operation.
2.5 Setting up the Detector
Block Connector
Camera Input
Audio Sensitivity Adjustment
Pyrosensor
Tamper
PIR
Sensitivity
Adjustment
Switch For
Settings

8
3.0 Potentiometers Adjustment
There two potentiometers located on the PCB device to set the optimal sensitivity of the
detection and the audio.
PIR Sensitivity Adjustment
• Use the Potentiometer marked “PIR” to adjust the detection sensitivity between 15%
and 100% according to walk test in the protected area. (Factory setting to 57%).
• Rotate the potentiometer clockwise to increase range, counter-clockwise to decrease
range.
Audio Sensitivity Adjustment
• Use the potentiometer “AUDIO” to adjust the audio sensitivity.
• Rotate the potentiometer clockwise to increase sensitivity.
• Rotate the potentiometer counter-clockwise to decrease sensitivity.

9
4.0 Testing The Detector
Wait one minute after applying power and warm up time.
Conduct testing with the protected area cleared of all people.
Walk Test
1. Remove front cover.
2. Set LED to ON position.
3. Reassemble the front cover.
4. Start walking slowly across the detection zone.
5. Observe that the LED lights whenever motion is detected.
6. Allow 5 sec. between each test for the detector to stabilise.
7. After the walk test is completed, you can set the LED to OFF position.
NOTE:
Walk tests should be conducted, at least once a year, to verify proper operation of the
detector.

Sales [phone]
Enquiries [email protected]o.uk
Website www.genieproducts.co.uk