Genmitsu 1010 User manual

INSTALLATION GUIDE
Genmitsu 1010 XY-Axis Extension kit
for PROVerXL 4030
V1.0 Feb.2022

Thank you for purchasing the Genmitsu 1010 XY-Axis Extension kit for PROVerXL 4030.
For technical support, please email us at [email protected].
Help and support is also available from our Facebook group. (SainSmart Genmitsu CNC Users Group)

01
Package List
X-axis Aluminum Extrusion
1
2×Y-axis Aluminum Extrusion
2
2×Front/Back Plate
3
2×M5*20 Screws
5
2×M5*14 Screws
6
2mm Hexagon Wrench
7
2.5mm Hexagon Wrench
8
3mm Hexagon Wrench
9
4mm Hexagon Wrench
10
Cable Management
(Drag Chain+Wiring)
4Installation Guide 11

Before Installation
02
Uninstall the parts that are marked as Yellow.

Before Installation
03
Step 1: Unplug all wiring and uninstall both cable chains.
Step 2: Uninstall X limit switch assembly.
Step 1 Step 2

Before Installation
04
Step 3: Uninstall X-Axis stepper motor and stepper motor mount, as well as all parts in blue.
Step 4: Uninstall red side plate from one side of X -axis and slide the X-Z assembly off of the X axis.
Step 3 Step 4

Before Installation
05
Step 5: Remove the Spoilboard and the Dust Baffle.
Step 6: Remove 2 blue corner brackets of the CNC Base Frame.
Step 5 Step 6

Before Installation
06
Step 7: Remove the Y axis Stepper Motor and 2 blue corner brackets of the CNC Base Frame.
Step 8: Remove the Y-Axis Limit Switch Assembly and Limit Block.
Step 7
Step 8

Installation Steps
07
Step 1: After disassembling your PROVerXL 4030, start by installing the longer aluminum extrusions into the blue
corner brackets using the same screws as before. All extended parts of the 1010 kit will be installed just the same
as their shorter 4030 counterpart, using the screws, spring washers and flat washers that you got from disassembly.

Installation Steps
08
Step 2: Install the coupler and motor, tighten the screws of the coupler after the motor is installed. The left and right
sides are installed in the same way.

Installation Steps
09
Step 3: Use the removed screws to install the Y-Axis limit blocks and limit switches, then adjust the limit switches
distance.

Installation Steps
10
Step 4: Install the mounting block and gantry assembly using the removed screws. The left and right sides are installed
in the same way.

Installation Steps
11
Step 5: Firstly, remove the side panel of the X-axis gantry (the side without the shaft), then slide on the X-Z assemble
so that the holes on the rear plate are aligned with the holes on the slider. With the X-Z assembly installed, put the side
panel back on and re-install all screws.

Installation Steps
12
Step 6: Install the left and right gantry arms with the removed screws.

Installation Steps
13
Step 7: Install the X-axis limit blocks with the removed screws and adjust the limit switches distance.

Installation Steps
14
Step 8: Install the X-axis drag chain fastener using the removed screws.

Installation Steps
15
Step 9: Install the X-axis drag chain using the removed screws.

Installation Steps
16
Step 10: Install the Drag Chain Mount and Drag Chain with the removed screws.

Installation Steps
17
Installation Completed

Parameter Setting
18
1. Enter $$ in Candle or other software control
port (console)
2. Check the original parameters and modify them
following:
$21=1
$22=1
$27=3
$30=10000
$100=200
$101=200
$102=160
$110=2000
$111=2000
$112=2000
$120=300
$121=300
$122=300
$130=1000
$131=1000
$132=55