GeoMax Zoom 75 Series User manual

Installation guide
GeoMax Zoom75/95 Series
English
Version 1.0

Table of contents
1 INTRODUCTION ...................................................................................................... 3
2 BATTERY CHARGING .............................................................................................. 3
2.1 Zoom75/95 instrument .......................................................................... 3
2.2 Field controller ..................................................................................... 3
3 PREPARATION OF THE INSTRUMENT ................................................................... 4
3.1 System files ........................................................................................ 4
3.2 Uploading the system files to the instrument ............................................. 5
3.3 Loading license files .............................................................................. 6
3.4 Configuration of the communication port ................................................... 6
3.5 Install USB driver for Zoom75/95 ............................................................ 7
3.6 Installing 3r d party software onboard the instrument ................................... 8

1 INTRODUCTION
This guide provides complete step-by-step instructions for preparing the Zoom75/95 TPS series
for measuring work. The instructions cover all the required installation tasks for the Zoom75/95
instruments.
The latest versions of GeoMax documents and software referred to in this document are all
available from the Technical Library of the GeoMax Parner Area in the Zoom75/95 folder at:
www.geomax-positioning.com/partner-area
Only the tasks required for the initial setup of a new Zoom75/95 system are described in this
document. For further information regarding the operation of the Zoom75/95 components,
please refer to the respective User Manual.
 The Zoom75/95 Quick Guide is included with the container set. The comprehensive User
Manual for the TPS instrument is available from the included USB stick and also from Technical
Library in the Zoom75/95 folder at www.geomax-positioning.com/partner-area
 The appropriate uses of the included accessories are described in the User Manual.
2 BATTERY CHARGING
2.1 Zoom75/95 instrument
Before using the instrument, the included ZBA400 battery should be charged. Insert the battery
into the ZCH201 charger and plug the adapter into an AC power supply. Do not disconnect from
power until the green FULL indicator flashes, indicating that the battery is fully charged. Once
charged, insert the battery into the side cover slot of the Zoom75/95 instrument and switch on.
2.2 Field controller
The Field Controller is supplied in a cardboard box which includes the device, battery and
charging adapter. Insert the supplied battery into the battery compartment of the device.
Charge the internal battery with the supplied adapter. Do not disconnect from power until the
battery is fully charged.

3 PREPARATION OF THE INSTRUMENT
3.1 System files
When receiving a new instrument, it should be checked that the latest firmware version is
installed. The installed version can be viewed in the installed “GeoMax Toolkit” application. To
access, start “GeoMax Toolkit” and select “SysInfo” (2). Select the second tab-page to view the
version information. If this version does not match the one available from GeoMax Technical
Library, then the instrument should be updated.
To customize the instrument according to personal preferences, the respective languages can
be installed. The necessary files can be obtained from the Thechnical Library of the GeoMax
partner area in the Zoom75/95/Firmware folder and have the following format:
- Zoom75_95_v.XXXX.fw is the main OS and application firmware file which by default
comes in English.
- GeoMaxToolkit_en_us.sus an example language file when “en” indicates the English
language and “us” stands for United States.

3.2 Uploading the system files to the instrument
The system files are loaded into the instrument directly from the SD card or USB stick.
Therefore, copy all downloaded files to the System directory of the SD card/USB stick. Insert
the SD card/USB stick into the corresponding port on the communication side cover of the
instrument and switch on the instrument. To upload files to the instrument, start GeoMax Toolkit
and navigate to MAIN MENU / APPS / UPDATE. If the firmware needs to be upgraded, install
it first by selecting F1 Firmware. Then install the preferred language file by selecting F2
Language.
Note: Ensure that fully charged batteries are inserted when uploading firmware. This
process can take some time and the power supply must NOT be interrupted during the loading
process. During the update process, it could be that the instrument will automatically reboot a
couple of times.

3.3 Loading license files
Some functions are licence protected and require a licence key to be uploaded. To upload a
licence key file, navigate to MAIN MENU / APPS / UPDATE / F3 Key and select the required
file for uploading. The key files are loaded directly from the SD card or USB stick, therefore,
copy the file to the System directory of the SD card/USB stick.
3.4 Configuration of the communication port
Zoom75/95 supports three communication options that can be configured as follow:
- Serial connection. If the optional ZDC229 data transfer cable has been purchased, a
serial connection can be established between the Zoom75/95 and the PC; to enable this
communication port, go to MAIN MENU / SETTINGS / COMM and select the RS232
option.
In addition, in order to use the ZDC229 data transfer cable, it is necessary to install a
driver on the PC which can be obtained from the GeoMax Partner Area Technical Library
in the Zoom75/95/Drivers folder under the name 'Zoom75&Zoom95 USB Driver'. After
downloading it, run the corresponding .exe file and follow the instructions of the installer
application to complete the process. Once the installation is complete, you can connect
the serial port of the Zoom75/95 to the PC using the serial cable.
- Internal Bluetooth. To enable the internal Bluetooth of the Zoom75/95 for connection,
go to MAIN MENU / SETTINGS / COMM and select the 3rd option by clicking on OK
button.
- Bluetooth Handle. If the ZRT82 long range Bluetooth handle is going to be used for
connection, replace the standard instrument handle with it. Swing the antenna into the

upright position. To configure the handle, choose MAIN MENU / SETTINGS / COMM. If
the handle is recognized, the "Bluetooth Handle (ZRT82)" option should be available, and if
the 'Power' LED on the handle is green, then select the option and click OK to enable it. In
case the 'Power' LED is off, perform a Windows reset by pressing the power key and selecting
the corresponding option; after the reset, the 'Power' LED on the handle will turn green and
the Bluetooth connection can be activated as just described.
3.5 Install USB driver for Zoom75/95
The instrument is equipped with a mini USB connector behind the side-cover. This USB
connection can be used to connect the Zoom75/95 to a PC to access its internal storage. Having
this option is useful for dragging and dropping files between your Zoom75/95 and the Dekstop
PC. In order to the PC to recognize the Zoom75/95, the USB driver of Zoom75/95 must be
installed. To install it, do the following:
- Download the ‘Zoom75 & Zoom95 mini-USB to USB driver’ from the Zoom75/95/Drivers
folder at GeoMax Partner Area Technical Library.
- Make sure the Zoom75/95 is not connected to the PC

- Run the Setup_GeoMax_USB_xx.EXE
- Follow the instructions on the screen
- When ready, press FINISH
- Power ON the Zoom75/95
- Connect the Zoom75/95 to the PC with a USB cable. Your PC will then try to recognize
the Zoom75/95 and associate the appropriate drivers with it.
- Press the Windows Start button at the bottom left corner of the screen of the PC
- Type the IP address of the device into the search field: \\192.168.254.3\
- Press Enter. A file browser opens with access to the folders of the instrument.
If connection is not possible, please refer to the ‘How to get Zoom75/95 USB driver running
on Windows10’ guide, which can be find at the Technical Library in Zoom75/95 folder.
3.6 Installing 3rd party software onboard the instrument
With the Zoom75/95 it is possible to install applications onto the unit if they were specifically
designed for it. If the received application installer is in .CAB format, it means that it has to be
transferred to the Zoom75/95 first before it can be installed. There are multiple ways of doing
this, but the easiest thing would be to put the .CAB file directly onto a USB-Stick and put this
stick into the Zoom75/95 USB port. Then on the desktop screen of the Zoom75/95, double-tap
on the MY DEVICE icon. Navigate to the USB stick and press ENTER. Now highlight the .CAB
installer and press ENTER to start the installation. Follow the instructions provided on the
screen.
If the received file is however an .EXE file, then it means that it would need to be run from the
Desktop PC side. Make sure that the instrument is powered ON and connected to the Desktop
PC. (See previous chapter). If the instrument is properly connected, run the .EXE file and follow
the instructions on the screen.

1.0.0en
© 2021 GeoMax AG is part of Hexagon AB.
All rights reserved.
GeoMax AG
Espenstrasse 135
9443 Widnau
Switzerland
geomax-positioning.com