GeoVision GV-GDR4900 User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual forfuture use. TVTG-QG-B
Quick Start Guide
GV-Cloud Cameras
GV-GDR4900
GV-GEB4900
GV-GEBF4911

©2023GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademark of Microsoft Corporation.
December 2023
Scan the following QR codes for product warranty and technical support
policy:
[Warranty] [Technical Support Policy]

i
Warning and Caution
⚫If the product does not work properly, please contact your dealer or the nearest service
center. Never attempt to disassemble the camera yourself. (We shall not be responsible
for any problems caused by unauthorized repair or maintenance.)
⚫Keep away from liquid while use.
⚫In the use of the product, you must be strict compliance with the electrical safety
regulations of the nation and region. When the product is mounted on wall, the device
shall be firmly fixed.
⚫Do not use camera beyond specified voltage range.
⚫Do not drop the camera or subject it to physical shock.
⚫Avoid touching the camera lens.
⚫If cleaning is necessary, please use clean cloth to wipe it gently.
⚫Do not aim the camera at the sun or extra bright place.
⚫Do not place the camera in extremely hot, cold, dusty or damp locations, and do not
expose it to high electromagnetic radiation.
⚫To avoid heat accumulation, good ventilation is required for operating environment.

ii
Contents
1. Overview..............................................................................................................1
1.1 GV-GEBF4911..............................................................................................1
1.2 GV-GEB4900................................................................................................3
1.3 GV-GDR4900 ...............................................................................................5
2. Installation...........................................................................................................8
2.1 GV-GEBF4911..............................................................................................8
2.2 GV-GEB4900..............................................................................................12
2.3 GV-GDR4900 .............................................................................................16
3. Accessing the Network Camera ......................................................................19
3.1 Looking Up the Dynamic IPAddress ..........................................................19
3.2 Configuring the IPAddress.........................................................................21
4. The Web Interface.............................................................................................22
5. Upgrading System Firmware ...........................................................................24
6. Restoring to Factory Default............................................................................25
7. Connecting to GV-Cloud VMS..........................................................................27
8. Connecting to GV-Center V2............................................................................30
9. Optional Installation .........................................................................................31
9.1 Junction Box GV-Mount506........................................................................31
9.2 Junction Box GV-Mount506-1.....................................................................35
9.3 Junction Box GV-Mount509........................................................................38
9.4 Wall Mount Bracket GV-Mount211-4...........................................................41
9.5 Wall Mount Bracket GV-Mount211-6...........................................................45
9.6 Wall Mount Bracket GV-Mount211-8...........................................................49
9.7 Wall Mount Bracket GV-Mount211-9...........................................................53

1
1. Overview
1.1 GV-GEBF4911
1
Ethernet connector (PoE)
7
Microphone
2
Audio input
8
Micro SD card slot
3
Audio output
9
Default button
4
Alarm input/output
10
Warm LED

2
5
Power port (DC 12V)
11
IR LED
6
Speaker
12
Active Deterrence LED
Note:
1. It is recommended to install the water-proof connector for outdoor installation.
2. To load default settings, press and hold the default button for 10 seconds.
Connecting Alarm Input/Output
Alarm Input
Alarm Output
Max. load: DC 30V, 1A

3
1.2 GV-GEB4900
10

4
1
Ethernet connector (PoE)
6
Fixed Screw
2
MIC-Audio input connector
7
Microphone
3
HP-Audio output connector
8
Micro SD card slot
4
Power connector (DC 12V)
9
Default button
5
Mounting Base
10
IR LED
Note:
1. It is recommended to install the waterproof connector for outdoor installation.
2. This series can be powered by DC 12V / PoE power supply. If the PoE switch is used
to power the camera, DC 12V power supply is not required.
3. To load default settings, press and hold the default button for 10 seconds.

5
1.3 GV-GDR4900
9

6
1
Ethernet connector (PoE)
6
Microphone
2
MIC-Audio input connector
7
Micro SD card slot
3
HP-Audio output connector
8
Default button
4
Alarm input/output
9
IR LED x 2
5
Power connector (DC 12V)
10
Note:
1. It is recommended to install the waterproof connector for outdoor installation.
2. This series can be powered by DC 12V / PoE power supply. If the PoE switch is used
to power the camera, DC 12V power supply is not required.
3. To load default settings, press and hold the default button for 10 seconds.
4. Make sure the camera’s lower dome is properly secured in case of microphone
operation failure.

7
Connecting Alarm Input / Output
Alarm Input
Alarm Output
Contact parameters of Relay:
Max. Voltage: DC 30V
Max. Current: 1A

8
2. Installation
2.1 GV-GEBF4911
Please make sure that the wall or ceiling is strong enough to withstand 3 times the weight of
the camera. Please install and use the camera in a dry environment.
1. Loosen the set screw and then move the camera unit to expose the cover of the SD
card slot.
2. Unscrew the cover of the camera unit and then insert a micro SD card. After that, install
back the cover and make sure the cover is installed firmly.

9
3. Drill the screw holes and the cable hole on the ceiling according to the drill template.
Then route and connect the cables.
(a). Loosen the nut from the main element.
(b). Run the network cable (without RJ 45 connector) through the both elements.
Then crimp the cable with RJ 45 connector.
(c). Connect the cable to the Ethernet connector. Then tighten the nut and the main
cover.

10
4. Secure the mounting base to the ceiling or wall with the screws provided.
5. Install the dome and enclosure to the mounting base.
6. Adjust the camera to obtain an optimum angle. Before adjustment, preview the
image of the camera on a monitor.

11
7. Tighten the set screw after you finish adjusting the viewing angle of the camera.

12
2.2 GV-GEB4900
Please make sure that the wall or ceiling is strong enough to withstand 3 times the weight of
the camera. Please install and use the camera in a dry environment.
1. Loosen the fixed screw to dissemble the camera.
2. Unscrew the cover of the dome and then insert a micro SD card. After that, install back
the cover and make sure the cover is installed firmly.

13
3. Drill the screw holes and the cable hole on the ceiling according to the drill template.
Then route and connect the cables.
(a) Loosen the nut from the main element.
(b) Run the network cable (without RJ 45 connector) through the both elements. Then
crimp the cable with RJ 45 connector.
(c) Connect the cable to the hermetic connector. Then tighten the nut and the main
cover.

14
4. Secure the mounting base to the ceiling or wall with the screws provided.
5. Install the dome and enclosure to the mounting base.
Then adjust the dome to obtain an optimum viewing angle.

15
6. Finally, fasten the camera with the fixed screw.

16
2.3 GV-GDR4900
Note:
1. Make sure that the wall or ceiling is strong enough to withstand 3 times the weight of
the camera.
2. Install the camera in the dry environment. You'd better install back the lower dome less
than 4 hours after removing it.
3. Do not remove the protection film until finishing the installation.
1. Use two fingers to remove the trim ring from the rim with marks. Then loosen the screws
to open the lower dome.
2. Attach the drill template to the place where you want to fix the camera and then drill 2
screw holes and 1 cable hole (if you want to route the cables through the ceiling)
according to the drill template.