Ger Detect FARM LIFE User manual

English User Manual


English User Manual

FARM LIFE
WATER DETECTOR
➢
Dear customer, thank you for choosing
FRAM LIFE. This product enables you to
detect the presence of underground water.
➢
FRAM LIFE product is based on
resistance principle. It measures the
resistance between surface electrodes
placed on surface of the region predicted to
have water. It compares the measured
values with the highest background values
and makes analysis.
Critical Warning
•••
Please be sure that all precautions
taken against risks
Do not use your device while it is
raining or on extremely wet floor
You have to be sure you are
connecting the electric cables correctly
You have to use the tall probes and
you have to install it under the ground
more 50 CM.
And don't install the probes into the
rocks.
Turn on your device after you make
sure that all parts are in place
Make sure that the device battery is
fully charged before searching
If the battery start to give a peep
sound, close the device and recharge
the battery
Do not start the pulse induction
system without connecting the coil
cable to the device, other ways the
device will stop in the middle of
opening
It is recommended to read the user
manual before start working on the
device to understand everything and
to avoid mistakes doing the search
After the device start make sound and
turn off automatically put the battery
on charge and do not try to start the
device without charging the battery
About the fresh result long range
system when the green light in the
charger that is mean the charge is full.
And about the geophysical system
when the green light in the device that
is mean the charge is full.
Be aware of high voltage resources, and do not use any
charger other than the original charger that come with
the device
Main unit of the device is under warranty against all
electronic breakdowns for two (2) years
Any damages caused by user errors (laying open the
main unit, hits, harms etc.) are not within this warranty
Battery and antenna are also not within this warranty
You should follow the instructions in this user manual
strictly to minimize the faults and to use your device
correctly
Warning: When we send the device to the customer,
we release the battery cables because the international
shipping laws, so you have to connect the battery cable
into the geophysical device.

English User Manual

Geophysical system
1
First: plant probes, installation of cables
Implant the probes in the soil even
85% minimum of the length of the
probes
- To get an accurate result the distance between the sensors should be
20 meters at the start of the search.
-When you do a search if the device given results no water, for example:
(probes between 1 and 2, then we must bring probes 1 and 2 toward
probes 3 and 4, a distance of one meter and re-search process)
-At the beginning of the search connect the cable between the probes
and the main unit of the device and make sure the plug correctly as
shown in the following picture
Also, make the distance between the 4 probes equal

English User Manual

The main unite and the operation steps
1- Power putton to open the device.
2- Charger signal light to now when the device is charging.
3- Charger entrence for 15 v sharger.
4- Fuse to protect the electronic circuit.
6- 4 entrance for the cable that contact the device with the probe.
7- Navigation buttons between the options.
8- Ok button to conform the options.
9- Screen for result display.

English User Manual

Second: please turn on the device and wait for a perio
d of not more than 5 seconds until the device initiates a
ction and show the working language of the device:
The device works on 3 languages, namely:
English. French. Arabic
In addition, you can choose the appropriate language se
arch by navigating up and down keys
After selecting, the language you want to work on the
device will take you directly to the main menu, which
contains
Start Search: through which the device will begin a
search for water
Between the probes and show a report, that contains the
results automatically.
Settings:we are through the settings determine the
type of soil in which to search and determine the distance
between the probes and determine the lighting of the
screen and the background color in order to facilitate the
search process and the vision clearly in bright sunshine
After selecting the settings, we return to the previous
menu, by pressing the OK key in order to confirm the
settings that we chose them before.
Start the search by clicking on the choice start scan,
which will make the device search between the four
probes. This process takes a maximum of 3 minutes
Picture (5)
Picture (4)
Picture (3)
Picture (2)
Picture (1)

English User Manual

Since the device is searching among the four sensors in 6 different way to gather all
information.
When the search process end the device will show you the results as follows:
1 - In the event of water under all probes you will see report on the device will appear from
which you can learn the whereabouts of water And the type of water as shown in the picture
In addition, for more details. You will press the OK button to know the density of the
water and salinity and water depth as shown in the following photo
Note: When the water percentage is less than 50% that means small amount of water, and
when the percentage is between 50-70% is a good amount of water, and when the
percentage is between 80-100% that means the water amount be huge

English User Manual

Important information
✓
If you give the device a "not connected" Please make sure probes is completely
implanted and connected the cables correctly.
✓If the device give you x in the search this x mean tow thing
✓1- Could be the cable not connect correctly.
✓2- could be the device had detect very salty water
✓
The difference that appears in the depth of the water (such as 80 > > 154) represents
the depth underground water.
✓
If using another battery charger, preferably 12 to 15 v no more and no less, that the
value of amps (2) and if you use a charger amp more will be the battery faster but will
have less battery life.
✓
Probe is then limited to a distance of 5 m between the sensors in case of find of water.
✓
If the distance between the probe 20 m you have to adjust the distance from the sitting
✓If the device give you on the screen few data about the depth
✓You have to research in the seam place to have the depth
✓
If the density of the water from 0% to 50 % that is means the water in small quantity in
this area / 50 to 60 % = medium quantity / 70 to 80 % = good quantity / 80 to 100 % =
huge quantity.
✓When the device gives you the salty water are salty and when it gives you a fresh
water with simple percentage salinity , this is the normal situation. All kinds of water
containing salinity
✓For salinity: the percentage of salinity is 10,000 parts per million Example
(40% means 4000 parts per million and 100% is 10,000 parts per million
means that the water is salty and invalid) The percentage make the conclusion
of salinity easy.
✓When you see the depth in the results, for example: (110-130 meters) and you re-
experience and the depth appear, for example, (120-160 meters) or (40-170 meters)
that is mean there is more than a water channel under the ground (there are several
Water channels with different depths at the same place
✓if you made several experiments in the same place and the depth was similar in all
the experiments that is mean there is a water basin and not stream water

English User Manual

Important NOTE
If you want to confirm the target once again in the same place, you must take off the floor
probes and change the place of the probe to other place at least one meter
To remove accumulation of charge as a result of the passage of the stream
To decompose water into oxygen and atomic+ hydrogen through the search process.
You should avoid using the machine during rain and must wait for 15 days at least after
the rain stopped until the soil dry out then you can use the device
Important NOTE
- Suppose the existence of drilled water wells in your area and work well and
starting at depths of 70 meters or 90, 100 or 120, 140, 160, 170 meters etc. ......
this is not conclusive evidence of existence of water only on these depths.
It could be at great depths.
-Example:
If it is proved you through the search process device that the depth
of this places from 200 to 240 meters this indicates the existence of water is
truly at these depths.
-As for the drilled wells and works depths less than 200 meters with very short
life, so must re-restored and drilling to the depth that the device showed.

English User Manual

Warning
If you want the device work well without errors you have to follow next steps
When using the device please do not wear the watch
When using the device please do not wear the jewelry
When using the device please get away from metal, lighter and mobile phone
Please take off the belt
The shoes should not contain any metal
Stay away from the car
Stay away from electrical ground power lines or any surfacing electric
We wish you the best of
luck in your searching
Thanks for choosing our
products