Ger Detect Titan Ger 500 User manual

English User Manual
Critical Warning
• • •
Please be sure that all precautions taken
against risks
Do not use your device while it is
raining or on extremely wet floor
Turn on your device after you make sure
that all parts are in place
Make sure that the device battery is
fully charged before searching
If the battery starts to give a peep
sound, close the device and recharge
the battery
Do not start the pulse induction system
without connecting the coil cable to the
device, other ways the device will stop in
the middle of opening
It is recommended to read the user
manual before start working on the device
to understand everything and to avoid
mistakes doing the search
After the device start make sound and
turn off automatically put the battery on
charge and do not try to start the device
without charging the battery
TITAN GER - 500
… DIAMOND AND GEMSTONES DETECTOR …
Overview
➢Dear customer, thank you for
choosing the TITAN GER –500
➢This device enables you to
detect underground diamond &
gemstones
➢TITAN GER –500 designed to reach
65 meters under the ground
➢and 3000 meters front range
➢Works by long range system to
confirm your target
➢and identify the target
underground and its depth
Be aware of high voltage resources, and do
not use any charger other than the original
charger that come with the device
Main unit of the device is under
warranty against all electronic
breakdowns for two (2) years
Any damages caused by user errors
(laying open the main unit, hits, harms
etc.) are not within this warranty
Battery and antenna are also not within
this warranty
You should follow the instructions in
this user manual strictly to minimize the
faults and to use your device correctly

English User Manual
1The Long-Range System
Figure (1) the long-range system components
This system specializes to cover vast areas and locate the target within 1-meter
Square up to depths of 65 meters below the surface of the ground and Front
Range up to 3,000 square meters.
The long-range system parts
Connect the handle
to the device
Figure (1) The handle

English User Manual
Connect the signal boosting
sensor
Connect the
transmitter antennas
Connect the Signal
Recipient
Figure (2) boosting sensor
Figure (3): Transmitter antennas
Figure (4): Signal Recipient

English User Manual
Connect the Recipient
Antenna
- Connect the
battery cable and
Switch the device
through ON / OFF button
Figure (4): Recipient Antenna
Figure (5): (ON / OFF) button

English User Manual
Figure (6): languages list
Click on the screen of the device to display the languages list the device
works on four languages:
(GERMAN - ENGLISH - FRENCH - SPANISH - ITALIAN - ARABIC)
Settings menu (Sound Adjustment –brightness adjustment, and
the device information)

English User Manual
Figure (9): Front Range Options
After selecting the language, you want to work in (English for example)
The target types menu will appear, choose the target type to be search for
from a list of options through pressing on the type name,
(big diamond for example)
You can flick through these lists with the NEXT button
It’s got a list containing a wider range of gemstones, which are 18 different
kinds.

English User Manual
Select the type of soil desired in the search area:
(natural - clay - rocky - sandy - mixed - mineralized).

English User Manual
Increase the length of the antennas receiving a signal
To able the device to detects targets even to 3000 meters
After selecting the Front Range, the digital compass will appear, Fix the
device at a 90-degree angle for the compass to work properly, then Press
the "Skip" button on the screen or the "OK" button on the keyboard.

English User Manual
Figure (10): search screen
After pressing on skip button, the light signals will appear directly on the
screen confirming that the device is sending and receiving signals that guide
you directly towards the target.
When a signal is captured, the device will immediately turn around towards
the target.
On the smart screen, there will appear the direction of the detected
target alongside a beep at the location of the target.
Figure (11): Increasing the length of the antennas

English User Manual
North to South
South to North
East to West
West to East
After detecting the target, confirm the target from four directions
Figure (14): determine the depth
To determine the depth of the discovered target, stand above target and
turn 45 degrees
Walk straight ahead until the antenna reverse to the back

English User Manual
Measure the distance between the antennas reversing back and the target
center point.
The distance between the antennas reversing back and the center point
is equal the target depth
For example, if the distance is 3 m the depth of the target is 3.
Thanks for choosing our
We wish you the best of luck
products
in your searching
Note: The target must be buried underground for many years so that by the time and
interaction with the soil’s composition, an ionic field will be formed which will help prospectors
to detect the target.
Therefore, testing the device on diamonds or gemstones laid on the ground or newly buried
under the ground will not show the real capacity and functionality of this device to detect the
target or to reach larger depths.
The reason for that is that the ionic fields are radiations from diamonds or gemstones that have
been in the ground for a long time and have intersected and interacted with the soil and the
nature of the earth as well as having been regulated with magnetic fields north and south –
These features do not actualize in diamonds or gemstones when they exist on the ground or
newly buried.

English User Manual
Warning
If you want the device work well without errors you have to follow next steps
When using the device please do not wear the watch
When using the device please do not wear the jewelry
When using the device please get away from metal, lighter and mobile phone
Please take off the belt
The shoes should not contain any metal
Stay away from the car
Stay away from electrical ground power lines or any surfacing electric