Ger Detect FRESH RESULT 2 SYSTEMS PLUS User manual

•Critical Warning
•Over view
•LONG RANGE SYSTEMS
oDescription the main unit keys
•Geophysical system
oDescription the main unit keys
oStart working with the geophysical system
oFirst step:
oSecond step
•No result message
oFirst case
▪The solution of this case
oSecond case
▪The solution of this case
oThird case
▪The solution of this case
•Important information and notes
•Warning
•Parts and accessories

-Please be sure that all precautions taken against all risks.
-Do not use your device while it is raining or on wet ground
-You have to be sure that you are connecting the electric cables correctly
- Use the four probes and you have to Plant it under the ground more than 25 CM.
- don’t ever try to Plant the probes into the rocks.
-Turn on your device after you make sure that all parts are in place
-Make sure that the device battery is fully charged before you start searching
-If the battery starts to give a peep sound, close the device and recharge the battery
-It is recommended to read the user manual before start working on the device to
understand everything and to avoid mistakes doing the search
-After the device start to make a sound and turn off automatically, put the battery on
charge and do not try to start the device without charging the battery
- while charging the long range system when the green light in the charger turn on, this
will mean the battery is full.
- while charging the geophysical system when the green light in the device turn on, this
will mean the battery is full.
-Be aware of high voltage resources, and do not use any charger other than the original
charger that come with the device
-Main unit of the device is under warranty against all electronic breakdowns for two (2)
years, any damages caused by user errors (laying open the main unit, hits, harms etc.) are
not within this warranty
-Battery and antenna are also not within this warranty
-You should follow the instructions in this user manual strictly to minimize the faults and
to use your device correctly
“Warning”:When we send the device to the customer, we release the battery cables
because the international shipping laws, so you have to connect the battery cable into the
geophysical unite.
Critical Warning

Dear customer,
“Thank you for choosing FRESH RESULT 2 systems plus”
✓This product enables you to detect the presence of underground water.
✓FRESH RESULT 2 systems product is based on resistance principle.
✓It measures the resistance between the four probes placed on surface of the region
predicted to have water.
✓It compares the measured values and analyze it and display the result on the screen
✓The device can reach depth of 1200 meter under the ground
✓The device front range is 2000-meter square
✓The device displays the result on a color screen 4.3 inch
✓The device works on 4languages (Germany –English –French –Arabic).
✓It’s passable to have your device with any language you like.
✓All parts and accessories are in 1 shockproof handbag.
✓The total weight of the device with all accessories is 10 kg.
✓The guaranty credit is valid for 2years.

1- LONG RANGE SYSTEMS
This system specializes to cover vast areas and locate the water up to depth of 1200 M
Below the surface of the ground and Front Range of 2,000 meters.
The transmission unit: the main unit of the device is placed on the ground in the
middle of the area to be discovered, we connect the antenna of the signal
Transmitter to the main unit and plant the probes on "5" meters from each other
And connect them to the device.
Then we turn on the device and select a language “for example English”
- When we choose a
language the device will
take you directly to the
“main menu”
(main menu screen)
Click on “searching
systems”which contain
two search systems:
1. The long range
system
2. geophysical
system
(search systems screen)

We move between the
search systems through
navigation buttons and
we select the
“long range system”
This screen will popup to
inform you to “turn on”
the Long range unit
(infomation screen)
After you turn on the
long range unite you will
see on the screen that
the device start to send
signals to the ground
and then you can start to
search for water
Note: extend the length of the antenna
in the main unite to reach maximum
range of the device and to caver more
area
- Then we move on to the long range unit
which works on Digital screen through
which you can determine the front range to
be reached in the search
By using this system
(main unit –long range system)

Description of the main unit keys –LONG RANG UNIT
Keys Description
1
Navigation button
2
Selection button
3
Power button
4
Back button
Note
Before opening the device,
the user should connect all
parts of the system and
connect the Handel to be
able to open the device
power
We turn the device through
the power switch
“ON –OFF”
first you will open the
button on the side of the
device
and then you will use the
ON / OFF key
o

We move between the
languages through
“navigation buttons”
And we conform our
selection by pressing
on OK button
After selecting the
Language, we choose
the type of water that
we will search for it
1- Fresh Water
2- Natural Water
Then we choose the
Front Range of the
search.
We navigate between
front range options
using the
“navigation buttons”
you can choose as
follow:
✓500 meters:
(from 0 to 0500 m)
✓1000 meters
(from 0 to 1000 m)
✓1500 meters
(from 0 to 1500 m)
✓2000 meters
(from 0 to 2000 m)
Press “OK BUTTON”
to select front range.

•After selecting,
the front-range
the device will
Begin the
process of
search.
•Carry the device
as in the photo.
➢The user should position them self from the north to the south which is the
best method to detect underground water.
➢As When the device detects any presence of water within the selected range
on the device the device will Track the signal and guide you directly to the
water location point Under the ground thus, this system will be done.
➢After detecting the target, conform the target from for direction
o“North to South”
o“South to North”
o“East to West”
o“West to East”
➢And to now the depth and salinity, type of water and the density of water
You will use the geophysical system.
“Note”
If the antenna is open to the maximum the device will guide you to more
than 1 location where water exists, so you must shorten the antenna to
the minimum to enable the device to guide you to the nearest target.

2- Geophysical system
This system allows you to discover more details about the discovered water after
using the long-range system, a survey and analysis of the underground water and
the way the system works in the following way
Description the main unit keys –Geophysical system

Keys Description
1
4.3 inch Screen for result display
2
BACK button to return back to return the previous page
3
Ok button to conform the options selected
4
Navigation buttons between the options (up –down –right –left)
5
Fuse to protect the electronic circuit
6
12 v. Battery entrance
7
Power button (ON/OFF) to turn on and turn off the device .
8
The transmission antenna for the long range system
9
4entrance for the cable that contact the device with the probes
10
RESTART button to restart the system
Start working with the geophysical system
First steps:
✓plant the 4 probes, and connect them with the 4 cables
✓plant the probes in the soil until 85% at lest of the length of the probes
✓To get an accurate result the distance between the probes should be 20
meters at the start of the search.
✓At the beginning of the search connect the cable between the probes and
the main unit of the device and make sure they are plugged correctly as
shown in the following picture
“NOTE”the distance between the 4probes should be the seam

Second step:
➢turn on the device and wait for a
period of not more than 5 seconds
until the device power up and display
the language options of the device
➢The device works on 4 languages,
(English. Germany. Arabic. French)
you can choose the language search
by using the navigation button
up and down keys
➢After selecting, the language you
want to work on the device will take
you directly to the main menu, which
contains:
1. Search systems
2. Setting
➢“Search systems” allowed you to
select the system that you want to
use it for searching, the device has
two search systems.
1. Geophysical system
2. Long range system
➢“Setting” allowed you to adjust
device settings,
the device has three options:
1. Soil type
2. Probe spacing
3. Brightness

➢“Soil type” to choose the type of soil
in which to search
➢“Probe spacing” to enter the
distance between the probes
according to your measurements on
the ground by using a meter
➢“Brightness” to adjust the lighting of
the screen
➢After adjusting the settings, we return
back to the previous menu, by
pressing the OK key in order to
confirm the selected options that we
choose them before
➢Now after you get back to the main
menu enter the search systems than
select the geophysical system and
wait for a few seconds and then the
device will start the search.

➢This scanning process will takes a
maximum of 3 minutes, Since the
device is searching among the 4
probes in 6 different way to collect all
information required to determine the
depth and the water type and all the
necessary information
➢After the device finish the search it
will take a few seconds to possess
the gathered information and display
it on the screen as we will see in the
end of search.
➢When the search process end the
device will display the results as you
see in the following photo:
➢In the event of water under all probes
you will see report on the device will
appear from which you can learn the
where about of water And the type of
water.
“Note”
When the water percentage is less than 50% that means small amount
of water, and when the percentage is between 50-70% is a good
amount of water, and when the percentage is between 80-100% that
means the water amount be huge

➢Dear customer,
When a "No result" message appears on the final search screen results
Please follow the solution of this case carefully.
First case
The solution of this case
The image above
showing us that the
device found water
only under the
line “A”
1- Move the probe
“3” From its
current location
To the location
of the probe “2”
2- Move the probe
“4” From its
current location
To the location
of the probe “1”
3- Redistribute
probes “1”, “2”
Depending on
the new location
of the probes
“3”,”4”
4- Re-search
again

Second case
The solution of this case
The image above
showing us that the
device found water
only under the
line “A”,line “B”
and line “E”
1-Determine the
center of triangle
which consist of lines
"A","B" and "E"
2-Move the probe “4”
From its current
location to the
triangle’s center.
3-Redistribute probes
“1” , “2” and “3”
Depending on the new
location of the probes
”4”
4-Re-search
again to get
complete results

Third case
The solution of this case
The image above
showing us that the
device found water
only under the line
“A” and line “B”
1-you can Follow the
steps described in the
“First case”
2-Or you can Follow
the steps described in
the “Second case”
1- Or move the
probe “4”From
its current
location
To the location
of the probe “2”
2- Redistribute
probes “1”, “2”
and “3”
Depending on
the new
location of the
probes ”4”
3- Re-search
again

“Important information and notes”
✓If the device displays the results “no water” in the search this will means two different things
o1- Could be the cable not connect correctly between the main unite and the probs.
o2- could be the device had detected very salty water.
✓The difference that appears in the depth of the water (such as 80 > > 154) Represents the surface
and the bottom of the discovered water.
✓If you will use a different battery charger, preferably you should use 12 to 15 v no more and no
less, and the value of Ampere is (2) and if you will use a charger with higher or lower Ampere it
will make your battery last lower than normal.
✓The distance between the 4 probes should be at least 20 meters to get more accurate result.
✓If the distance between the 4 probes is 20 m each you have to adjust the distance in the sitting.
✓If the device gives you on the screen (few data) you should do the search again in the seam
location.
✓If the density of the water lower than 50 % that means the water exist in small quantity in this area
and it’s not recommended to drill according to this result.
✓If the density of the water is from 50 % to 60 % that means the water exist in medium quantity
✓If the density of the water is from 70 % to 80 % that means the water exist in big quantity
✓If the density of the water is from 80% to 100% that means the water exist in very big quantity
✓When the device discovers salty water the result will be on the primary result of the search it will
show (salty water)
✓When the device discovers very salty water the result will be on the primary result of the search it
will show (very salty water) and this water is Non-drinkable and Not usable

“Important information and notes”
✓the Salinity of the water is to Measure the percentage of the Salts in the water
✓When you see the depth in the results, for example: (110-130 meters) and you research again and
give you, for example, (120-160 meters) or (40-170 meters) for example, that is mean there is more
than 1 water well under the ground (there are several Water wells with different depths at the same
place)
✓if you made several search in the same place and the depth was similar in all the times that is mean
there is an underground water leak and not stream water
✓If you want to confirm the target once again in the same place, you must take out the probes and
change the place of the probe to other place at least one meter far a way to remove accumulation of
charge as a result of the passage of the stream
✓You should avoid using the machine during rain and must wait for 15 days at least after the rain
stopped until the soil dry out then you can use the device
NOTE:
✓Suppose the existence of drilled water wells in your area and working well and
starting at depths of 10 meters or 50, 100 or 120, 140, meters etc. ...... this is not
conclusive evidence that the water existence only on these depths. It could be
there is a water at more depths.
That means the final result of depth on the device screen is the real depth of huge
amount of water.
Example: If it is proved you through the search process device that the depth of
this places from 200 to 240 meters this indicates that the existence of water is
truly at these depths.
As for the drilled wells and works depths less than 200 meters with very short life,
so must re-restored and drilling to the depth that the device showed.

When using the device please do not wear any watches
When using the device please do not wear any jewelry
When using the device please get away from metals, lighter
and mobile phone and video games.
Please take off your belt in the search presses
The shoes should not contain any metal
Stay away from cars in your search
Stay away from electrical ground power lines or any
surfacing electric
Warning
If you want the device work well without errors, you have to follow next steps