Getz Equipment Innovators BV 101 P User manual

GETZ EQUIPMENT INNOVATORS
PART NO.: 3G58634
MODEL: BV 101 P
PNEUMATIC BELT VISE

BELT VISE
PART NO.: 3G58634
TABLE OF CONTENTS
PAGE #
1 ........................................................... SPECIFICATIONS AND REQUIREMENTS
2 ........................................................... SET-UP AND OPERATION PROCEDURE
3 ........................................................... PARTS LIST
4 ........................................................... SCHEMATIC
5 ........................................................... SCHEMATIC
6............................................................ SCHEMATIC
7............................................................ TROUBLE SHOOTING

SPECIFICATIONS AND REQUIREMENTS
SPECIFICATIONS:
HEIGHT - 38 INCHES (96.5 cm)
WIDTH –16.75 INCHES (42.5 cm)
LENGTH –27.25 INCHES (69 cm)
WEIGHT - 130 LBS (59 Kg)
SHIPPING WEIGHT - 154 LBS (70 Kg)
SHIPPING CONTAINER SIZE:
HEIGHT –41.75 INCHES (106 cm)
WIDTH –18.5 INCHES (47 cm)
LENGTH –31.5 INCHES (80 cm)
REQUIREMENTS:
AIR SOURCE
1. CO2 VAPOR
2. NITROGEN
3. COMPRESSED AIR
MAXIMUM CYLINDER HOLDING DIAMETER:
Ø12 INCHES (30 cm)
OPTIONAL EQUIPMENT:
3G59407-KIT ROLLER VISE: ALLOWS VISE TO ACCOMMODATE CYLINDERS UP TO 16
INCHES.
1G51957-SLIP JOINT DEVALVING WRENCH
"CAUTION"
1. THIS BELT VISE MUST HAVE A REGULATED AIR SOURCE OF NO MORE THAN 140
P.S.I.
2. OPERATOR MUST KEEP HANDS CLEAR OF THE BELT WHEN OPERATING THIS
VISE.
3. OPERATOR MUST WEAR SAFETY GLASSES WHEN OPERATING THIS VISE.
1

SET-UP AND OPERATIONS
REFER TO SCHEMATIC
Step 1 - Locate the belt vise in an area where the operator will have acces to adjust the belt
handle (item #20) and room to devalve the cylinder.
Step 2 - After placement of the belt vise, bolt base plate to the floor with lag screw or bolts to
secure the vise from moving when devalving cylinders.
Step 3 - Remove the plastic connectr (item #19) from the yellow air line (item #7) and thread
tape or place sealant on the male pipe threads.
Step 4 - Screw the plastic connector (item #19) into the outlet port on your regulator and
reconnect the yellow line (item #7) to the plastic connector (item #19).
Step 5 - Push the air control valve handle (item #5) down and set your regulator min. –100
PSI to. –140 PSI.
Step 6 - Remove the belt handle (item #20) from the slots in the belt vise and adjust the
horse shoe (item #4) in the proper holes for the size of cylinder being devlaved.
Step 7 - Place the cylinder to be devalved on top of the horse shoe (item #4) of for larger
cylinders, remove the horse shoe (item #4) and place the cylinder in the front V of
the belt vise.
Step 8 - Reinsert the belt handle (item #20) back into the farthest slot on the vise that can be
reached.
Step 9 - Remove hands from belt on vise and pull up on air control valve handle (item #5).
Step 10 - After making sure no pressure is in the cylinder being devalved, place your
devalving wrench on the cylinder valve and screw the valve ou of the cylinder.
Step 11 - Push down on air control valve handle (item #5( while holding onto the cylinder, and
remove the belt handle (item #20) from the slot in belt vise and remove the cylinder.
Step 12 - Follow step #6 through Step #11 on other cylinders.
2

PARTS LIST
NO. PART # DESCRIPTION QTY
1 1G51835 STAND PEDESTAL ONLY 1
2 1G51725 PLATE RESTRAINING BELT 2
3 1G58512 BELT 33 WRAP AROUND ONLY 1
4 1G51411 HORSE SHOE 1
5 3G59484 VLV PUSH/PULL PARKER W/KNOB 1
6 1G51230 CONNECTOR PLAS 3/8 MPT X 1/4 TUBE 2
7 1G0047 MTL NYCOIL 1/4 YL 10 FT
8 1G0047 MTL NYCOIL 1/4 YL 1 FT
9 1G0047 MTL NYCOIL 1/4 YL 1 FT
10 1G51717 PLATE BACKING BELT 1
11 1G51548 ANGLE HOLDING BELT 1
12 1G0397 CYL SMC FOR BELT VISE 1
13,22,23 1G54432 MOUNT CLEVIS CYL SMC 1
14 1G51791 SCREW SOCKET 1/2 X 2 1
15 3G58582 PAD CYL 1
16 1G51142 BOLT ELEVATOR 1/4 X 1 6
17 GRADE 5 BOLT HEX HEAD 1/4 X 1 4
18 1G51286 DECAL PANEL VISE 1
19 1G0136 CONNECTOR PLAS 1/4 ML X 1/4 TUBE 1
20 1G51378 HANDLE BELT 1
21 1G51878 TRAY TOOL 1
24 1G51583 NUT MOUNTING VALVE 1
3

TROUBLESHOOTING
PROBLEM SOLUTION
1) Vise isn’t holding cylinder 1) a. Adjust pressure to 100-140 PSI
b. Check for air leaks & repairs
2) Air leak in control valve 2) Replace valve –P/N: 3G59484
3) Air leak in air cylinder body 3) Repair air cylinder cylinder P/N: 1G0397
4) Air blows out exhaust post 4) Repair air cylinder cylinder P/N: 1G0397
on air valve continuosly
5) Belt broken, worn, or torn 5) Replace belt –P/N: 3G58512
Replace belt assembly –P/N:3G58514
6) Bent air cylinder shaft 6) Replace air cylinder –P/N: 53235 &
install belt roller kit –P/N: 3G59407
Use the following kit for general service and maintenance –P/N: 3G58895
7