GFW MORITZ TALL User manual

Size:
Colour:
Finish:
)HDW(mc7.281x6.91x9.42
White
Melamine with High Gloss Fascias
MORITZ TALL CABINET ASSEMBLY INSTRUCTIONS
Thank you for purchasing the Moritz Tall Cabinet.
Please read the instructions carefully to ensure safe operation of this product,
especially the installation warnings shown in Page 2 of this Assembly Instruction.
Version 1 - 200707
PO No：
Page 1of 14
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking.
Tools Required
1 Hour
Set Up

Version 1 - 200707
Page 2of 14
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
CARE INFORMATION
To clean, wipe with a damp cloth.
Never use scourers, abrasives or chemical cleaners.
Do not use solvent based cleaners or detergents as they can bleach or damage the product.
This product is designed to hold 8 Kg in total, spread evenly over the whole unit.
Do not exceed this weight.
We recommend that this unit is assembled in the room intended for use.
When you are ready to start, make sure that you have the right tools, plenty of space and a
clean, dry area for assembly.
Unwrap all packaging materials and place the components on top of the carton box or on a
clean floor to prevent them from scratching.
Check the pack and make sure you have all the parts listed.
Ensure that this product is fully assembled as illustrated before use.
Check all screws or bolts are tightened and inspect regularly
Tools not included unless specified in parts list.
WARNINGS
DO NOT
DO NOT
DO NOT
DO NOT
use power tools to construct this product.
tighten screws until parts are assembled or as advised in this guide.
over tighten screws or bolts.
use this product if parts are missing, damaged or worn.
This is a slim unit, for safety it is designed to fix to the wall using the anti-tilt bracket (H).
MORITZ TALL CABINET ASSEMBLY INSTRUCTIONS
INSTALLATION WARNINGS:
In order to prevent the cabinet tipping over, this product must be installed with the metal
anti-tilt bracket provided (H).
It is essential for the safety of you and your children, the cabinet is not free-standing.
Carefully assess the suitability of the wall to ensure that the fastening device will
withstand the load and forces generated.
Walls can be quite different in construction so only fixings for a standard block wall are
supplied - otherwise please choose the most suitable fixing for your wall type - if in doubt
consult an expert.
When drilling the wall always be sure the area to be drilled is free from hidden electrical
wiring, water or gas pipes.
The fixing of this product to the wall must be done carefully following the detailed stages
in the assembly guide. See Steps 8 and 9.

Version 1 - 200707
Page 3of 14
Parts and Fittings Checklist
MORITZ TALL CABINET ASSEMBLY INSTRUCTIONS
10
11
12
13
14
15
X 1
X
X
Y
Z
2
3
1
1
4
5
6
6
6
7
8
8
9
16
Please check the pack contents before assembling the product. If any components are
missing, please contact your retailer.
The fittings pack contains small items that should be kept away from children.
There are a number of the shelves that are identical size and look the same except for some
surface holes, e.g. 5 & 15. Please refer to the part No label adhered to each shelf.
For clarity the three different options are shown below, X, Y & Z.
Please check carefully before fitting or it could waste a lot of time.

All parts are packed in one carton
Base Panel
Description:
Qty: 1
mm51x181x2961:eziS
Carton No: 1/1
Description: Fixed Shelf
Qty: 1
Size:218 x 166 x 15 mm
Carton No: 1/1
Carton No: 1/1
Carton No: 1/1
45
Qty: 1
Qty: 1
mm51x181x2961:eziS
mm51x181x942:eziS
123
Description: Fixed
Shelf Qty: 3
Size:218 x 166 x 15
mm Carton No: 1/1
Description: RH Side Panel
Description:
Size:218 x 166 x 15 mm
Carton No: 1/1
Description: Adjustable Shelf
Qty: 3
6
Size:120 x 30 x 30 mm
Carton No: 1/1
Description: LegsBack Panel
Qty: 2
Carton No: 1/1
7 8
Qty: 1
mm3x622x4961:eziS
Description:
Size:640 x 249 x 15 mm
Carton No: 1/1
Description: Upper Door
Qty: 1
9
mm51x29x841:eziS
Carton No: 1/1
Description: LH Drawer SideDrawer Front
Qty: 1
Carton No: 1/1
10 11
Qty: 1
mm51x0001x942:eziS
Description:
Size:148 x 92 x 15 mm
Carton No: 1/1
Description: RH Drawer Side
Qty: 1
12
:
mm3x141x191:eziS
Carton No: 1/1
Description: Drawer BaseDrawer Back
Qty: 1
Carton No: 1/1
13 14
Qty: 1
mm51x88x381:eziS
Description:
LH Side Panel
Version 1 - 200707
Page 4of 14
MORITZ TALL CABINET ASSEMBLY INSTRUCTIONS
X
Y
Description: Fixed Shelf
Qty: 1
Size:218 x 166 x 15 mm
Carton No: 1/1
15
Lower Door
Carton No: 1/1
16
Qty: 1
mm51x942x046:eziS
Description:
Z
Hole for
anti tilt bracket
Inserts for
drawer stops
Shelf Type
Shelf Type
Shelf Type

MORITZ TALL CABINET ASSEMBLY INSTRUCTIONS
A28mm
A
A
Stop when
level
General Hints & Tips
B
Tighten
FLUSH
CARCASS SCREW
Version 1 - 200707
Page 5of 14
4C Screw for Fitting Drawer
Sides (3.5x40mm)
Screw for Fitting Hinge,
Back Panel (3x12mm)
24A
24B
D 21
Item QuantityCode
Fittings (to scale)
Cam Lock
10 20 30 40 50 60 70 80
Cam Bolt
(38mm overall)
Carcass Screw for
Fitting Base Panel (4)
to Side Panels (2 & 3)
(M7x50mm)
4E
2F Bolt for Fitting Legs
(M6x35mm)
6
1
GBolt for Fitting Handle
(M4x18mm)
Screw for Fitting Anti-tilt
Bracket to Fixed Shelf
(4x12mm)
P