GGM gastro VHCOZ 20 User manual

20 LT.&30 LT. CUTTER
( ELECTRICAL –INDUSTRIAL TYPE )
USER’S MANUAL
Published on : 22.08.2019
•PRODUCTION SITE : GGM Gastro International GmbH Weinerpark 16 48607 Ochtrup
Tel: [phone] / 7220 0 Fax: [phone]
Our website: www.ggmgastro.com e-mail: [email protected]
MANUFACTURER :GGM Gastro International GmbH.
MODEL: VHCOZ 20
MODEL: VHCOZ 30
1/16

TABLE OF CONTENTS
PAGE NR. TOPICS
1 COVER PAGE
2 TABLE OF CONTENTS
3 INTRODUCTION
4 TECHNICAL DATA
5-6 ELECTRICAL CIRCUIT DIAGRAM,CONTROL BOARDS
7 MAIN DIMENSIONS
8 WARNING SIGNS
9 SAFETY DETAILS
10 TRANSPORTING AND MOVING
11-12 INSTALLATION OF THE APPLIANCE
13-14 OPERATION OF THE APPLIANCE
15 CLEAN-UP AND MAINTENANCE
16 TERMS OF WARRANTY
2/16
CAUTION
The power network of the building, facility or any similar site, where this
device will be connected to power supply, should comply with “INDOOR ELECTRICAL
INSTALLATION” regulation all necessary action should be taken in order to maintain
personal and material safety when connecting this device to power supply.
OTHERWISE OUR COMPANY WILL NOT BE RESPONSIBLE FOR THE CONSEQUENCES.

3/16
INTRODUCTION
Dear User,
Thank you for purchasing our appliance and for your reliance upon our company.
Our appliances are used in professional kitchens in 100 countries. Our appliances are
produced in compliance with international standards. Important notice: Please read and ensure
that the users read this user’s manual in order to achieve the desired performance in line with
your expectations and to use your appliance for long years. Please take the
warnings mentioned above into consideration before calling for service...
•Please read and ensure that your operation personnel also reads this user’s
manual care fully before installing and using the appliance. If the appliance is
operated without reading the user’s manual, the appliance will not be covered
by the warranty.
The manual containing information about installation, usage and maintenance
of our product you purchased should be read carefully. Please ensure that
power supply connections to the appliance are already installed by qualified
personnel according to local legislation, before our authorized service
personnel arrives for the installation of the appliance.
If you are confused or you don’t have enough information
please get in touch with authorized service by phone.
Please keep in mind that, if the service personnel is delayed
at your site, related expenses and delay costs will be charged to
you on hourly basis.
We hope that you will get the best performance from our product…

YOUR PRODUCT'S TYPE VHCOZ 20
(Mono phase)
VHCOZ 30
(Three phase)
MAIN DIMENSIONS (mm) 480x700x1070 480x740x1070
TOTAL ELECTRICAL INPUT (kW) 2,2 3
POWER SUPPLY VOLTAGE 220-240 380-400
OPERATIONAL CAPACITY
(KG/BATCH) 8-15 18-25
WORKING FREQUENCY (Hz) 50/60 50/60
SUPPLY CABLE 3x2,5 5x2,5
MAXIMUM NOISE (dBA) 77 77
MAXIMUM SLOPE 5°5°
PROTECTION CLASS 1 1
CLASS IP21 IP21
BOWL CAPACITY (lt)20 30
MATERIAL STAINLESS STEEL STAINLESS STEEL
NET WEIGHT (Kg) 68 75
TECHNICAL DATA
4/16

VHCOZ 20
ELECTRICAL CIRCUIT DIAGRAM
5/16

ELECTRICAL CIRCUIT DIAGRAM
6/16
CONTROL BOARDS
POTATO PEELER
VHCOZ 30

MAIN DIMENSIONS
7/16
VHCOZ 20
480x700x1070
VHCOZ 30
480x740x1070

POWER SUPPLY CONNECTIONS
POWER NETWORK GROUNDING GROUNDING
220-240 V NPE / 50/60 Hz
VOLTAGE : 220-240 V
SUPPLY CONNECTION: 1 PHASE
POWER
8/16
WARNING SIGNS
PE
380-400 V 3NPE / 50/60 Hz
VOLTAGE :380-400 V
SUPPLY CONNECTION: 3 PHASE

SAFETY DETAILS
☞This device should be installed in line with
effective regulations and only be operated in well
ventilated places. Please refer to the instructions
before installing and operating the device.
☞This device is designed for industrial use and
should only be operated by personnel trained on
the device.
9/16
☞Do not clean up the device with pressure water
☞The device should not be handled by
unauthorized persons except for the
manufacturer or authorized service.
☞In case of fire or flame in the area where the
device is operated, act without panic, close gas
valves (if any) , turn off the power switches and use
a fire extinguisher. Never use water to extinguish the
fire.

TRANSPORTING AND MOVING
CHANGING THE LOCATION;
Machines installed by an authorized service
CANNOT BE MOVED ELSEWHERE, ITS POWER SUPPLY
CABLES CANNOT BE EXTENDED OR REPLACED except
by an authorized service.
10/16
☞Disconnect from power supply before moving
☞The vehicle can be moved with supplementary vehicles like fork lift.
☞The device should be placed on a palette by manpower.
☞If the transported distance is far, the machine should be moved
slowly and the device should be fixed on palette or supported in order
to prevent jolt.
☞Do not hit or drop the device when moving.

Installation of the device should be carried out
by authorized service personnel.
INSTALLATION OF THE APPLIANCE
☞Bowl should be placed
correctly(1) and locked by
turning around(2) its axis
shown in the picture.
☞After ensured about bowl
placed correctly, blades should
be placed(3) to shaft shown as
above picture.
11/16
☞Power supply connection of the device should be checked by
an eligible electrician, and it should be connected to a fuse at
a maximum height of 170 cm.
☞Power supply connection should be made using a 30 mA
current leakage fuse as a protection against current leakage
danger.
☞Power installation to be used should be grounded by
connecting it to a grounding bar at the nearest panel.
Relevant fuse values to be used according to device power
are given in Technical Data section (Page 4).
1
1
2
3

CONTROL PANEL
12/16
☞After ensured about bowl and blades placed correctly, top
cover should be placed and locked to shaft shown in the
picture.
Vegetable
inlet Oil
inlet
Lock
Bowl Drain
Arm
ABC
A: START BUTTON
B: SPEED CONTROL
C: STOP BUTTON

OPERATION OF THE APPLIANCE
13/16
1. Cutter machine is used for cutting of onion, tomato, pepper,..etc vegetables without
leaving the juice and not allowing them to crush. Because of the cutter, some mixtures can
be prepared properly.
2. After placing the machine to the operation area with its package, and then open its
package.
3. Before first use, machine should be cleaned thoroughly together with its outer surface
and internal boiler with a liquid cleaning material and rinsed with plenty of water.
4.Because of the safety, connect the machine to a grounded socket.
5. During the operation, hardness material should be awared from the bowl.
6. Motor safety cover plate placed under the machine should not be opened, do not
change the parameters of motor driver, do not repair motor,belt etc by non-authorized
persons.
7. It should be ensured the bowl is placed to the machine properly.
8. After pressed start button, 8 staged speed switch should be increased slightly upto
necessary speed.
9. During the operation, bowl cover should not be opened.
10. Keep the control panel beware of water.
11. When the cutting operation is completed properly, machine is stopped by pressing the
stop button.
12. Blades of cutter should be checked periodically and in case of low cutting performance
with blades, blades should be replaced with the new ones.
13. Do not use abrasive or such harsh chemicals in the cleaning of the machine.
14. In case of any damage caused by user’s fault will not be covered in warranty.
15. Blades given with the cutter machine should be stored in safety regions.
16. Before using bowl drain arm, blades must be taken from bowl. This prevents any
dropping of blades from bowl.
NOTE: Do not use except purpose of use. The device should be operated by
qualified personnel knowing safety terms and technical specifications and who has
read the instruction manual.
CAUTION !
NEVER OPERATE YOUR DEVICE
WITHOUT GROUND CONNECTION.
It is recommended to operate the device between temperatures of -5ºC +40ºC
and in ambient humidity of maximum 65%.
CAUTION !
NEVER ENTER YOUR HAND IN TO THE BOWL
UNLESS THE BLADES ARE NOT STOPPED.

OPERATION OF THE APPLIANCE
CAUTION! : The device should be installed and operated as
described in this user’s manual. If any failure is encountered
please contact our nearest authorized service dealer.
WHEN THE DEVICE HAS A FAILURE ONLY AUTHORIZED
………….. SERVICE DEALERS ARE ALLOWED TO HANDLE
THE DEVICE. IF ANY PERSON OTHER THAN ONLY
AUTHORIZED SERVICE DEALERS HANDLE THE DEVICE,
IT WILL NOT BE COVERED BY THE WARRANTY.
NEVER ALLOW PEOPLE WHO ARE NOT AUTHORIZED TO
HANDLE THE DEVICE. OTHERWISE PRODUCER
COMPANY WILL NOT BE RESPONSIBLE FOR THE
CONSEQUENCES. DURING MAINTENANCE SERVICE OUR
AUTHORIZED SERVICE DEALERS SHOULD NOT BE
PROPOSED TO USE NON-ORIGINAL SPARE PARTS FOR
WHATSOEVER. INSTALLING ANY NON-ORIGINAL SPARE
PART TO THE DEVICE LEAVES THE DEVICE
OUT OF WARRANTY COVERAGE.
14/16

1. CLEAN-UP:
Turn the device off after daily use. Wipe the outer surface of the mixing
apparatus and container with a sponge and liquid detergent. Top hood may be
opened, to remove the peeler disc and to discharge rests left inside the vessel
with help of water.
After clean-up with sponge and liquid detergent mixing apparatus and container
should be rinsed thoroughly with plenty of water.
Do not use CHEMICAL CLEANING AGENTS like hydrochloric acid and
abrasive materials during cleaning.
2. CLEAN-UP:
Periodic maintenance should be carried out by a technician. It is
recommended to carry out maintenance at least every 6 months, depending
on the frequency of use. Periodic maintenance conducted by authorized
service personnel of ours is charged, even the guarantee period has not
expired.
CLEAN-UP AND MAINTENANCE
15/16
LIFE OF USE
Devices life of use is 10 year if it is used under recommended conditions.