Giada F110D Series User manual

1/ 5
Giada F110D/F102D Series Assembly Guide v1.1
Thank you for choosing Giada product. In such an epoch of PC development, we launched Giada
Barebone which is characterized by the mini shape, vogue and ultra-thin structure, environment
friendly, Giada will allowyou to undergo new experience in the field.This Guide shows you how to do
installation and uninstallation quickly and correctly.
WARNING:
This motherboard contains static-sensitive components and should be handled with care. Failure to employ
adequate anti-static measures can cause partial or complete device failure, performance degradation, or
reduced operating life. The battery must be replaced with the correct type of lithium cell battery; otherwise
there is a risk of damage to the motherboard. To avoid electrostatic discharge (ESD) damage upon handling
this product, it is strongly recommended that you wear a grounded wrist strap or other static dissipating
device.
CONTENT:
Memory, SSD, Wireless Module and HDD installation
Remark: The picture shown in this document is only a model of our series products, the actual
object is subject to change depends on the model you purchase.
Part 1. Appearance
The Front and Right Panel.
The Back and Left Panel.
Power Switch
Power LED
For antenna
DC-IN
VGA
Clear CMOS
HDMI
2*Rj45
4*USB 2.0
4 in 1 Card Reader
Audio out
Mic in
USB Port
1*COM
1*COM
Kensington
Lock Hole

2/ 5
Part 2. Chassis disassembly
Unscrew (anti-clockwise) the screws
from bottom panel of the PC.
Push away the bottom panel as the
arrows shown and then take it away.
If you need to install HDD, you need
to release the inner antenna which
connected to the top panel, and then to
remove the top panel.
Unscrew (anti-clockwise) the screws
from Top panel of the PC and remove
the Top panel (be careful the inner
antenna which for BT).

3/ 5
Part 3. RAM/SSD/WIFI/HDD assembly
Install the RAM (F110D only
support DDR3L 1.35V module).
Insert the SSD to the slot, make sure it
is locked with 1 screws.
Insert the WIFI Module to Mini-PCIe
slot, make sure it is locked with 1
screws.
Connect Wi-Fi cable and inner
antenna to the Wireless Module.
Attention for the place of Wi-Fi
cable and BT cable, there is mark
1(main) and 2(AUX) in the red
circle, usually 1 for Wi-Fi cable, and
2 for BT cable.
Remark:
The inner antenna and external antenna
cable are for WIFI or BT, but not for
3G module (F102D not support 3G).
Install SATA HDD to the Board as the
arrows direction.
Turn over the whole PC, and fix the
HDD with 3 HDD screws as the
picture shown.
WIFI/3G
SSD
RAM

4/ 5
IR Module assembly (only
F102D need)
Install the infrared card with 2 screws
as the pictures shown.
After the completed installation of the
infrared card, the next step is
connecting cable. One of connect cable
end be fixed in the card, the other end
is to be fixed into the slot as the picture
shown in red circle.
Both sides of IR cable can connect
to the IR Module.
Remark:
F110D no need to assemble the IR
Module which have integrated on
the Mainboard.
Part 4. Chassis assembly
For model F102D:
Before cover the top panel, you must
to make sure the one thermally
conductive pad has spliced well on
the Heat sink which is very
important for heat dissipation.
For model F110D:
Before cover the top panel, you must
to make sure the Two thermally
conductive pads has spliced well on
the HDD (thick type pad) and Heat
sink (thin type pad) which is very
important for heat dissipation.
Need to remove two
sides protective film
Thick type
pad for HDD
of F110D
Thin type pad for Heat sink

5/ 5
Assemble the top panel with the inner
antenna across the chassis. And then
fix the top panel with screws.
Push back the bottom panel as the
arrows shown and then fix it with the
screws.
Fix WiFi antenna or 3G antenna.
Then the whole installation is done.