Giada F300 Series User manual

Giada F300 Series Assembly Guide
Thank you for choosing Giada product. In such an epoch of PC development, we launched Giada
Barebone which is characterized by the mini shape, vogue and ultra-thin structure, environment
friendly, Giada will allow you to undergo new experience in the field. This Guide shows you how to
installation and uninstallation quickly and correctly.
WARNING:
This motherboard contains static-sensitive components and should be handled with care. Failure to employ
adequate anti-static measures can cause partial or complete device failure, performance degradation, or
reduced operating life. The battery must be replaced with the correct type of lithium cell battery; otherwise
there is a risk of damage to the motherboard. To avoid electrostatic discharge (ESD) damage upon handling
this product, it is strongly recommended that you wear a grounded wrist strap or other static dissipating
device.
CONTENT:
HDD, Memory, Wireless Module, 3G Module and SSD installation.
Remark: The picture shown in this document is only a model of our series products, the actual
object is subject to change depends on the model you purchase.
HDD, Memory, Wireless Module, 3G Module and SSD installation
Part 1. Appearance
The Front Panel.
The Back Panel.

Part 2. HDD installation
Unscrew (anti-clockwise) 2 screws from top
panel of the PC.
Pull up half of the top panel and then turn it
over avoiding the Thermal conductive strip
dropping out.

Unscrew (anti-clockwise) 2 screws from the
HDD Stand, and take off the HDD Stand.
Remark:
White screws are for WiFi/3G/SSD module.
Two black screws are for fixing HDD.
Four Circular Foot-paddings are for PC
stand.
Take another two black screws from the
accessory bag and fix HDD to the HDD
Stand (two sides).
Install HDD to the Mother Board as the
picture shown, and fix it with the screws.
Push back the half of top panel and make
sure the Thermal conductive strip can paste
in place for better heat dissipation.

Part 3. Memory, Wireless Module, 3G Module, SSD installation
Unscrew (anti-clockwise) the screw from
the bottom cover plate.
Push the cover plate as the picture
shown.
Take away the cover plate and then you can
see one SO-DIMM Slot for Memory,
three Mini-PCI Express® ( Full-length for
mSATA ⅢSSD; Full-length for
PCIE/USB/3G; Half-length for PCIe).
Remark:
The two black wires are used for connecting
the external Antenna to the Wireless
module, but not for connecting 3G module.
MSATA
WiFi
3G

Wireless Module installation
Insert the module to M-PCIE slot, make
sure it is locked with 1 screws.
Connect Wi-Fi cable or BT cable to the
Wireless Module.
As the two wire is the same, there is no
need to distinguish which one is the
main antenna.
If you Wireless Module is full-length, you
can install it to the middle slot.
SSD Module installation
Insert the SSD to M-SATA slot, make sure it
is locked with 1 screws.
3G Module installation
Insert the module to M-PCIE slot, make
sure it is locked with 1 screws.
Connect 3G cable to the Module.
As two black wires installed are used for
Wireless module, but not for 3G module,
you need to install the cable for 3G module.
Move the SIM Card slot as the picture
shown, then you can open it to install your
3G SIM Card.

Memory installation
Install the Memory module to the
SO-DIMM slot as an angle about 35 degree,
then press down the module to the Slot
lightly until it`s locked.
Cover Plate assembly
Take the cover plate back and push the
cover plate as the picture shown.
Fix the screw back.
Fix WiFi antennas or 3G antenna.
Paste on four Circular Foot-paddings as the
picture shown.
Then the whole installation is done.