Giant CITYSTORM User manual

CITYSTORM USER GUIDE
1
Congratulations on your purchase of a GIANT Citystorm.
GIANT Citystorm represents the latest in design and
engineering, and also requires special care. While Giant
Bicycle engineers have used the best quality, most durable and
lowest maintenance materials in this Citystorm, you must follow
certain guidelines to attain optimal performance and proper
wear characteristics.
WARNING Failure to follow these Instructions will
void your warranty, and may result in hidden damage to
the Citystorm. Damage to the Citystorm can cause loss
of structural integrity, which may result in serious
personal injury.
!
Lock
Front light
Rear light
Stem watch
Front light
Take out the battery holder
from the stem
CAUTION The battery has polarity (+/- sides), so
be sure to install the battery with the + side upward as
shown in the diagram.
!
Turn 90° counterclockwise
with a coin to loosen the
battery holder
How to re
p
lace the batter
y
Replace the battery (AA SIZE)
with a new one.
Step 3: Battery
Battery holder
Battery holder
+
-
Step 1:
Step 2:
Loosen the rear light fixing bolt
with 4mm Hex key.
Remove the rear light and fixing
link.
Install onto saddle IN THE
FOLLOWING ORDER: one
rear light, one fixing bolt.
Tighten the rear light fixing bolt
with 4mm Hex key.
Tightening torque:2.9-5.8Nm
Step 1:
Step 1:
Step 2:
Rear light
How to re
p
lace the batter
y
Replace the battery (SIZE AAA)
with a new one.
Step 2:
How to install the rear li
g
ht onto saddle
-
+
-
CAUTION The battery has polarity (+/- sides), so
be sure to install the battery as shown in the diagram.
!
Fixing link
+
Fixing bolt
Take out the cover with coin.

CITYSTORM USER GUIDE
2
Lock
1688
How to use lock
Adjust dials to let your
combination align with the mark.
Step 1:
Warranty
Please refer to the Giant Owner’s Manual or visit our
website: www.giant-bicycle.com for complete provisions of
the warranty.
After deciding how to lock the
bike, push the lock in and turn to
the lock position.
Step 3:
Stem watch
How to use stem watch?
Method of display the date:
Press the button A to display the DATE.
Method to display the time:
Press the button A twice to display the time.
Method of setting:
Step1: Press the button B twice to enter setting mode.
Step2: Press the button A to change the value.
Step3: Press the button B to confirm the setting and
move to the next digit to be set.
Step4: Set each digit in order from date to time.
Step5: After the minutes have been set, press the button
A to return to the normal display.
How to re
p
lace the batter
y
?
Loosen the stem watch fixing bolt
with 3mm Hex key.
Tightening torque: 1.9-3.4Nm
Step 1:
Push the stem watch up with
3mm Hex key.
Step 2:
Stem watch fixing Bolt
Loosen the cover fixing screw
with screwdriver.
Step 3:
Replace the battery (LR921) with
a new one.
Step 4:
A
B
A: SET
B: MODE
CAUTION The battery has polarity (+/- sides), so
be sure to install the battery with the + side upward as
shown in the diagram.
!
mark
Then release the lock from the
bike.
Step 2:

CITYSTORM SERVICE INSTRUCTION
1
Read these instructions carefully before using, and follow them
for correct use.
Lock
Front light
Rear light
Stem watch
Front light
Take out the battery holder
from the stem
CAUTION The battery has polarity (+/- sides), so
be sure to install the battery with the + side upward as
shown in the diagram.
!
Turn 90° counterclockwise
with a coin to loosen the
battery holder
■How to replace the battery
Replace with new battery
(AA SIZE).
Step 3: Battery
Battery holder
Battery holder
+
-
Step 1:
Step 2:
■ How to assemblethe front light
Note: You must install the front light first
before install the handlebar stem.
Install the front light to the head
tube; make sure the button is
at the top position.
Install the handlebar first and
then connect the front light
connector.
Step 2:
Step 3:
Button
Rotate the front fork and pull out
the wire at the same time, make
sure the length > 150mm.
Step 1:150mm
■ How to disassemble the front light
Disconnect the front light from
the connector.
Step 2:
Pull out the front light from the
head tube.
Step 1:
Button
Front light

CITYSTORM SERVICE INSTRUCTION
2
Stem watch
■
How to use stem watch?
Method of displaying the date:
Press the button A to display the DATE.
Method to display the time:
Press the button A twice to display the time.
Method of setting:
Step1: Press the button B twice to enter setting mode.
Step2: Press the button A to change the value.
Step3: Press the button B to confirm the setting and
move to the next digit to be set.
Step4: Set each digit in order from date to time.
Step5: After the minutes have been set, press button A
to return to normal display.
■
How to re
p
lace the batter
y
?
Loosen the stem watch fixing bolt
with 3mm Allen key.
Tightening torque: 1.9-3.4Nm
Step 1:
Push the stem watch up with
3mm Allen key.
Step 2:
Bolt
Loosen the cover fixing screw
with screwdriver.
Step 3:
Replace the battery (LR921) with
a new one.
Step 4:
A
B
A: SET
B: MODE
CAUTION The battery has polarity (+/- sides), so
be sure to install the battery with the + side upward as
shown in the diagram.
!
Loosen the rear light fixing bolt
with 4mm Allen key.
Remove the rear light and fixing
link.
Install onto saddle IN THE
FOLLOWING ORDER: one
rear light, one fixing bolt.
Tighten the rear light fixing bolt
with 4mm Allen key.
Tightening torque:2.9-5.8Nm
Step 1:
Step 1:
Step 2:
Rear light
■
How to re
p
lace the batter
y
Replace with new battery
(SIZE AAA).
Step 2:
■
How to install the rear li
g
ht onto saddle
-
+
-
CAUTION The battery has polarity (+/- sides), so
be sure to install the battery as shown in the diagram.
!
Fixing link
+
Fixing bolt
Take out the cover with coin.

CITYSTORM SERVICE INSTRUCTION
3
Installation of the front fork
1688
Insert the front fork into head
tube and pull out the wire for the
front light from the head tube.
Step 1:
Wire
Warranty
Please refer to the Giant Owner’s Manual or visit our
website: www.giant-bicycles.com for complete provisions
of the warranty.
■ How to replace the lock
Prior to dismantling the lock
Remove front light from the head tube.(see page 1)
Remove front fork
1688
Loosen the lock fixing bolt with
5mm Allen key.
Tightening torque: 4.9-7.8Nm
Step 1:
Pull out the lock
Step 2:
Step 3: Repeat Steps 1~2 in reverse to install the new lock
Bolt
Installation of the hook
Loosen the cable fixing bolt.
Make sure that the quick release
of the brake is in open position.
Step 1:
Insert the front brake cable
through the hook.
Step 2:
Step 3:
B
Hook
Front brake cable
Hook
Hold the front brake
cable and shifter
cable with hook.
These two cables
should parallel.
Step 4:
Adjust the hook in the
suitable
p
osition.
Bolt
Lock
After deciding how to lock the
bike, push the lock in and turn to
the lock position.
Step 3:
1688
How to use lock
Adjust dials to let your
combination align with the mark.
Step 1:
mark
Then release the lock from the
bike.
Step 2: