Gifas-electric FONTO 2290 User manual

Floor socket outlets FONTO
Page 1 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
Floor socket outlets FONTO
Manual
VERSION
MODIFICATIONS
1.0
Creation of the document
1.1
More detailed information in chapter 3 and 4
1.2.
Complement chapter 4 (07.02.2020 roen)
1.3.
Complement FONTO 8000 (08.07.2020 roen)

Floor socket outlets FONTO
Page 2 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
Table of contents
1General information................................................................................................................3
1.1 Marking concept for hazards and hints............................................................................3
1.2 Responsibilities of the operator........................................................................................3
2Introduction ............................................................................................................................4
2.1 Disposal of the device .....................................................................................................4
2.2 Technical data.................................................................................................................4
2.3 Installation conditions......................................................................................................5
3Installation examples FONTO................................................................................................6
3.1 FONTO 2290...................................................................................................................6
3.2 FONTO 2295...................................................................................................................6
3.3 FONTO 3290...................................................................................................................7
3.4 FONTO 3295...................................................................................................................7
3.5 FONTO 3301...................................................................................................................8
3.6 FONTO 3308...................................................................................................................8
3.7 FONTO series 4000 ........................................................................................................9
3.8 FONTO 8000.................................................................................................................10
3.9 FONTO 1970D..............................................................................................................11
3.10 FONTO 1970W .............................................................................................................11
3.11 FONTO 3970W .............................................................................................................12
3.12 FONTO 1975.................................................................................................................12
3.13 Please note...................................................................................................................12
4Installation examples FONTO levelable..............................................................................13
5Connection / Handling floor sockets FONTO .....................................................................14
5.1 FONTO 1970W .............................................................................................................15
5.2 FONTO 3970W .............................................................................................................15
5.3 FONTO 1975.................................................................................................................16
5.3.1 Handling FONTO 175 ........................................................................................17
6Service ..................................................................................................................................18
6.1 Service addresses.........................................................................................................18
6.2 Imprint...........................................................................................................................18

Floor socket outlets FONTO
Page 3 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
1 General information
1.1 Marking concept for hazards and hints
Hazard
Hazardous situation which will cause serious injury or even death if it is not prevented.
Caution
Hazardous situation which could cause slight to moderate injury if it is not prevented.
Hint
Indicates information which does not concern personal injury, e.g. hints in respect of material damage.
Protective measures
Increase safety by applying a protective measure.
1.2 Responsibilities of the operator
-Make sure that this document is always kept in a safe place in a legible form together with the product.
-Read these instructions carefully before first start-up of the product.
-This product has been developed and produced exclusively for the use indicated in these documents.
Every other use, which is not mentioned explicitly, could affect the intactness of the product and/or
could constitute a source of danger.
-The manufacturer rejects any liability for damage which has been caused by incorrect or non-intended
use of the product.
-In countries, which do not belong to the European Community, the national legal reference regulations
as well as the standards and regulations applicable in these countries have to be observed for warranty
of a corresponding safety level.
-The installation has to be carried out according to the applicable regulations.
-The manufacturer assumes no liability for inexpert execution of installation as well as deformations
which may occur during operation.
-The electric power supply has to be switched off before executing any action on the installation.
-Exclusively original parts of the manufacturer shall be used for maintenance. Maintenance work may
be carried out by qualified staff only.
-All procedures which are not explicitly mentioned by the manufacturer in the instructions are not per-
mitted.
-The packing material must not be stored within the reach of children as it could be a potential source
of danger.

Floor socket outlets FONTO
Page 4 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
2 Introduction
To ensure proper installation, the following steps and notes must be complied with under all circumstances.
Only this way can it be ensured that the product will work to complete satisfaction.
Hint
Read all instructions before starting installation. Our sales department will be happy to answer any questions
you may have.
2.1 Disposal of the device
This product must not be thrown in the garbage.
In accordance with official local and national regulations, this product is to be recycled appropri-
ately.
European directive 2012/19/EU; waste electrical and electronic equipment (WEEE).
2.2 Technical data
This electrical distribution box (see type label) is manufactured to standards EN61439, IM22 and complies to
EU low voltage directive 2014/35/EC.
Nominal voltage, nominal power and max. permissible fuse are mentioned at the type label
Short circuit resistance
max. 10 kA or manufacturing documents
Rated peak withstand voltage
4 kV
Rated insulation voltage
400V - Test voltage: 2.5 kV
Temperature range
-25°C to +40°C
Max. relative humidity
100% at +25°C decreasing linearly to 50% at +40°C
Max. Altitude
2000m above sea level (by using above 2000m consult the
producer)
Pollution degree
3
Transport and Storage
Please only use grab handle or lifting eyes. No special storage.
Be aware that the packaging is not damaged.
Cleaning
If dirty, clean with cleaning tissue or brush. Do not use abra-
sives or solvents
The use of the distribution box may only by having a properly constructed and function checked (measured)
low-voltage system. If there are special operating conditions, please contact your dealer or the manufacturer.
The feeder must be according to the rule (ÖVE, VDE or national norms) resulting cross-section. In order to
avoid electrochemical corrosion of the power terminals and busbar, only copper wire or aluminum wire with
AlCu-terminals can be connected.
If the distribution has mechanical damage (broken cable or sockets, cracks, fissures, ....) and/or electrical
defects the distribution box may not longer be used.
Periodic inspections are according to the current national guidelines.
Repairs and inspections should only be done by the professionals
(in accordance to national regulations) by using original spareparts
to ensure the users safety and to ensure proper function.

Floor socket outlets FONTO
Page 5 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
2.3 Installation conditions
GIFAS-ELECTRIC GmbH accepts no liability in cases where the product has been used inappropriately or not
as intended. The selection and use of the product are the exclusive responsibility of the individual operator.
Product liability claims, warranties also as guarantees made by GIFAS-ELECTRIC GmbH with respect to the
product are voided, if it is not used, serviced or maintained in accordance with the instructions in this manual.
Hint
To ensure permanent tightness and function of the floor outlets following points should be noted:
-For the assembly of the floor socket, a fixed base must be present. A montage of floor socket in lots
soil (gravel, sand, ...) is not allowed.
-The cable glands must be suitable for the particular cable diameter.
-Before closing the floor socket remove all pollution.
-The floor sockets must be cleaned regularly from dirt. All seals should be checked for damage and
must be greased when needed.
-If the floor sockets are installed in floors with floor heating or in places with temperature fluctuations
(cold circulating air), condensation water may form. This can be remedied if the socket is regularly
ventilated or operated with an attachment ring fitted.
-All cable glands must comply with protection class IP68.
-Water must be prevented from entering the housing.

Floor socket outlets FONTO
Page 6 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
3 Installation examples FONTO
3.1 FONTO 2290
1. Floor covering
2. Backfill
3. 2x cable gland M25 (across)
4. Mortar bed to align
3.2 FONTO 2295
1. Floor covering
2. Backfill
3. 2x cable gland M25 (beside)
4. Mortar bed to align
5. 1x cover cable outlet

Floor socket outlets FONTO
Page 7 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
3.3 FONTO 3290
1. Floor covering
2. Backfill
3. 2x cable gland M25 (beside)
4. Mortar bed to align
3.4 FONTO 3295
1. Floor covering
2. Backfill
3. 2x cable gland M25 (beside)
4. Mortar bed to align
5. 2x cover cable outlet

Floor socket outlets FONTO
Page 8 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
3.5 FONTO 3301
1. Floor covering
2. Backfill
3. 2x cable gland M25 (beside)
4. Mortar bed to align
5. 2x cover cable outlet
Hint
The cover is removable.
3.6 FONTO 3308
1. Floor covering
2. Backfill
3. 2x cable gland M25 (beside)
4. Mortar bed to align
5. Recessed lid for 9 mm stone
6. 2x cover cable outlet
Hint
The customer is responsible for fixing the stone in the recess. There are no special requirements.

Floor socket outlets FONTO
Page 9 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
ca. 110 - 155mm
ca. 83mm
3.7 FONTO series 4000
1. Floor covering
2. Backfill / under floor
3. 2x cable gland M25
4. 4x levelling feet M8
FONTO 4290 FONTO 4295 FONTO 4301
FONTO 4308
5. Cover cable outlet
6. Recessed lid for floor covering
Hint
FONTO 4290 / 4295 closed IP20
FONTO 4290 / 4295 hinged cover
FONTO 4301 / 4308 closed IP20
FONTO 4301 / 4308 Removable cover
FONTO 4308 for several floor coverings
(Adjustable ca. +/- 6mm)

Floor socket outlets FONTO
Page 10 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
3.8 FONTO 8000
1. Floor covering
2. Backfill / under floor
3. 3x cable gland M25
4. 4x levelling feet M8
5. Cable outlet on cover
Hint
FONTO 8301 removable cover
FONTO 8308 removable cover / for various floor coverings
(level-adjustable after installation approx. +/- 6mm)
approx. 95mm
approx. 125-165mm
90-100mm
240mm
240mm

Floor socket outlets FONTO
Page 11 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
3.9 FONTO 1970D
1. Floor covering
2. Backfill
3. 2x cable gland M25 (across)
4. Mortar bed to align
Special: screwable lid
3.10 FONTO 1970W
1. Floor covering
2. Backfill
3. 2x cable gland M25 (underside of the housing)
4. Mortar bed to align
5. Silicone joint
6. Water height maximum 20 mm

Floor socket outlets FONTO
Page 12 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
3.11 FONTO 3970W
1. Floor covering
2. Backfill
3. 2x cable gland M25 (beside)
4. Mortar bed to align
5. Silicone joint
6. Water height maximum 20 mm
3.12 FONTO 1975
1. Floor covering
2. Backfill
3. 2x cable gland M25 (across)
4. Mortar bed to align
5. 2x cable gland M32 (underside of the housing)
6. Levelling support (alternative to mortar bed)
7. Water protection pipe with 2x cable outlet
8. View without cover
3.13 Please note
- Ensure that the floor socket is the same level with the top edge of the floor covering.
- The floor sockets must not be driven over with grinding machines when closed.
- It is generally recommended to create a silicone joint between the floor covering and the floor socket.

Floor socket outlets FONTO
Page 13 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
4 Installation examples FONTO levelable
1. position the floor socket and fix the levelling feet (option)
2. Level the upper edge of the floor socket to the ground surface
3. Lay pipes or cables
4. Put on the protection cap (part of the packaging)
5. Backfill the socket with load-bearing material (concrete, mortar)
6. Remove the protection cap before the floor covering is laid
7. Use the levelling screws to make a fine adjustment to the floor level
8. Caulk the joint between the floor socket and the floor covering
Hint
With the inner levelling screw, a difference of +/-6mm can be
compensated
Hint
Depending on the position of the lid, the floor socket
is IP20 or IP65

Floor socket outlets FONTO
Page 14 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
5 Connection / Handling floor sockets FONTO
Opening of floor outlet i.e. removal of the insert holder:
1. Open the cover of the junction box.
2. Unscrew the insert holder.
3. Pull out insert holder.
4. Connect the sockets.
The replacement and closing takes place in reverse order.
Hint
The metal socket must be properly connected to the earth conductor.

Floor socket outlets FONTO
Page 15 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
5.1 FONTO 1970W
5.2 FONTO 3970W
1.)
to open
to fix
2.)

Floor socket outlets FONTO
Page 16 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
5.3 FONTO 1975
Opening of floor outlet i.e. removal of the insert holder:
1. Unscrew the cover with an allen Key (size 5) counterclockwise.
2. Extract the water protection tube.
3. To connect the sockets you have to remove the 4 pc. screws at the insert holder (allen Key size 3)
4. Pull out insert holder to connect the sockets.
The replacement and closing takes place in reverse order.

Floor socket outlets FONTO
Page 17 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
5.3.1 Handling FONTO 175
1
4
0

Floor socket outlets FONTO
Page 18 / 18
Created
12.12.2016
KHSH
Modified
08.07.2020
roen
Object-ID
1144626
6 Service
6.1 Service addresses
GIFAS ELECTRIC GmbH
GIFAS-ELECTRIC S.r.l
GIFAS ELECTRIC GmbH
GIFAS-ELECTRIC GmbH
Borsigstrasse 9
Via dei Filaracci 45
Strass 2
Dietrichstrasse 2
Piano del Quercione
Postfach 275
D-41469 Neuss
I-55054 Massarosa (LU)
A-5301 Eugendorf
CH-9424 Rheineck
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
www.gifas.de
www.gifas.it
www.gifas.at
www.gifas.ch
[email protected]
inf[email protected]
ver[email protected]
[email protected]
6.2 Imprint
GIFAS-ELECTRIC GmbH
CH-9424 Rheineck
www.gifas.ch
Technical changes and errors reserved.
These installation instructions are the property of GIFAS-ELECTRIC GmbH and may not be copied, tran-
slated, transferred, duplicated or passed on to third parties without the previous written consent of GIFAS-
ELECTRIC.