Gigant Flex 200 User manual

Flex 200
Worktable – Operating instructions

2
A
B
C
DEFG H I J
K L M
4x 4x
8x 6x 10x
N
12x
1x 4x
2x
2x
1
A
G
I
H

3
B
B
I
I
J
J
K
K
2
L6x
3

4
4
N
M
12x
D
C
E
F
M

andra föremål t ex. intillstående bord eller utrustning samt väggmonterade hyllor etc. pga. kläm-
stativets ställbara fötter.
nslut bordets stickpropp till 230V~, ±10 %, 50 Hz.
appen på bordskontrollen trycks in en eller två gånger och sedan hålls intryckt tills bordet når
att gå tillbaka upp ca 5mm. Släpp inte knappen förrän bordet står still.
oceduren är genomförd, aktiveras inte bordet utan proceduren måste tas om ifrån början. Ib-
ånger för att aktiveringen ska starta, beroende på att elektroniken kan bef nna sig i olika lägen.
erna driver på båda sidorna.
hetsanordningar monteras enligt MPI TEKNIK AB’s anvisningar. Vid förf yttning av bordet skall
s tyngd.
industriell miljö/kontorsmiljö och för intermittent bruk på 10 %, dvsmax 6 min på1 h eller
elar. Stativet ska kompletteras
ska motorer som är kopplade
pbenet. I varje teleskopben
yftrörelse. Ljudtrycksnivån
EKNIK AB’s bl.a. följande
går fritt från annan utrustning.
ktion. (Motorn går så länge bordskontrollen aktiveras.)
eligger klämrisk mellan skiva eller stativ och intillvarande utrustning.
ått på bordet skall tipprisken beaktas.
skiva ska klämrisken beaktas.
objekt på bordsskivan då detta kan orsaka personskada.
t, slaglängd eller övre/nedre ändläge förändras behöver en manuell reset utföras, se Installations-
strömmen brytas genom att stickproppen dras ut ur uttaget.
fabriken och därmed underhållsfria.
Elektrisk motor
Bordsskiva
Teleskopben
Bordskontroll
Styrbox
Installation instructions
• Place the table at least 120 mm from other objects, eg,
adjoining tables, equipment, wall mounted shelves, etc to
avoid trap hazard.
• Make the top of the table level, ie, with the aid of the
adjustable feet on the frame.
IMPOr TAn T!
T e table must be activated by press the down button on the
table control one or two times and then keep the button pressed
until the table has reach its bottom level. T e table will then raise
app. 5mm. Don’t release the button until the table stands still.
Observe! If the button is released before the complete procedure
is carried out, the table will not be activated and the procedure
has to be started from the beginning again. Sometimes the down
button has to be pressed two times to start the activating due to
that the electronic can be in dif erent positions.
• Ensure that electric cables are undamaged and plug in the
power cable of the table, 230 V AC, ±10%, 50 Hz.
• Test run the table and ensure that the drive axle works on both
sides.
Additional safety devices must be mounted in accordance with
instructions from Gigant if the table is to be placed in series.
When moving the table, never lift it by the top of the table
because the frame is too heavy.
Description
T e table is made for indoor use in an industrial or of ce envi-
ronment and for 10% intermittent lifting operation, ie, max
2 min per 18 min.
Conf guration
T e f gure shows the main parts of the table. T e table should be
completed with a suitable tapletop from Gigant product range.
Accessories
Accessories that are approved by Gigant for tables Flex 200
include the following:
• Set of wheels.
• Drawer and drawer suspension.
• Extensionframe for extensions.
• Table control with 3 memory positions.
• Tiltable tabletop.
• Undershelf.
Operating instruction
Raising and lowering the table
• Ensure that the table top, and anything placed on the table,
has clearance in relation to surrounding objects.
• Press the switch to give the desired action. (T e motor runs so
long as the switch is actuated.)
WAr n In G!
Observe the danger of crushing between the table top or frame
and adjoining equipment when raising and lowering.
T e danger of tipping must be considered if load protrudes
beyond the extent of the frame.
For tables with a top that can be sloped:
WAr n In G!
Observe the danger of crushing if the table is f tted with an
adjustable sloping top.
T e top may not be sloped when loose objects are on the table
since this could otherwise result in personal injury.
Manual reset / zero position
In case of a failure so that the teleskopic legs are not working
parallel, stroke or upper / lower end position is changed, a manual
reset has to be performed, please see Installation Instructions.
Maintenance
T e power cable must be unplugged before attempting any
service work on the table.
All moving parts are lubricated at the factory and are therefore
free from maintenance.
Function
Lifting action of the table is achieved by an electric actuator
in each teleskopic leg. Glide plates f tted in each telescopic leg
ensure smooth and even lifting action. T e sound pressure level
of the table is lower than 70 dB(A).
Control box Table top
Control switch
Electric actuator
Telescopic leg

www.gigant.co.uk