Gigant Flex 375 User manual

Flex 375
Worktable – Operating instructions

G
H
A B C D E
F G H
4x 8x 4x 8x 25x
4x 4x 4x
I
4x
1
2

3
A
C
F
250 mm
3
2

4
4
B
D
I
5

5
6
7
E
E

Installation instructions
• Place the table at least 120 mm from other objects, eg,
adjoining tables, equipment, wall mounted shelves, etc.
• Make the top of the table level with the aid of the adjustable
feet on the frame.
• Ensure that electric cables are undamaged and that everything
is f tted according to the assembly instructions.
• Plug in the power cable of the table, 230 V AC, ±10%, 50 Hz.
• Press the downbutton and continue to hold the button pressed
until the table has reached to the bottom. Release the button
and press it again. After approximately 5 seconds, you will
hear a clicking sound from the control unit. T e resetting will
then be ready and the product can be put into use. It may be
necessary to repeat the procedure later to ensure that parallel
operation is satisfactory.
If the table is to be placed in series then additional safety devices
must be f tted in accordance with instructions by Gigant.
When moving the table, never lift it by the top of the table
because the frame is too heavy.
Description
T e table is made for indoor use in an industrial or of ce
environment and for 10% intermittent lifting operation, ie,
maximum 6 minutes per hour (maximum 2 minutes continuous
operation).
Conf guration
T e f gure shows the main parts of the table.
Function
Lifting is achieved by two electric motors that are interconnected
with a control unit. Glide plates f tted in each telescopic leg
ensure smooth and even lifting action. T e sound level of the
table is lower than 70 dB(A).
. intillstående bord eller utrustning samt väggmonte-
ötter.
enligt monteringsanvisningen.
ra sig nedåt. När stativet nått bottenläge, släpp knap-
ett klickande hörs ifrån styrenheten. Nu är nollställ-
oceduren upprepas senare, för att säkerställa att paral-
monteras enligt MPI TEKNIK AB’s anvisningar.
nd av stativets tyngd.
kontorsmiljö och för intermittent bruk på 10 %, dvs
Bordsskiva
Teleskopben
Ställdon
Manöverdon
Styrenhet
r samman-
r som ger
70 dB(A).
bl.a. föl-
utrustning.
år så länge manöverdonet aktiveras.)
ellan skiva eller stativ och intillvarande utrustning.
tipprisken beaktas.
en beaktas.
van då detta kan orsaka personskada.
lan 6 och 8 användas.
Table top
Telescopic
leg
Actuator
Table con-
trol
Control unit
Accessories
Accessories that are approved by Gigant for tables
Gigant Flex 375 include the following:
• Hand control with f exible cable.
• Foot pedal.
• Supplementary frame.
• Manual tilting of table top.
• Motor powered tilting of table top.
• Drawer and drawer suspension.
Operating instruction
Raising and lowering the table
• Ensure that the table top, and anything placed on the table,
has clearance in relation to surrounding objects.
• Press the table control to give the desired action. (T e motor
runs so long as the table control is actuated.)
WAr n In g !
Observe the danger of crushing between the table top or frame
and adjoining equipment when raising and lowering.
T e danger of tipping must be considered if load protrudes
beyond the extent of the frame.
For tables with a top that can be tilted:
WAr n In g !
Observe the danger of crushing if the table is f tted with an
adjustable tilting top.
Caution. T e top may not be tilted when loose objects are on the
table since this could otherwise result in personal injury.
Maintenance
A detergent with a pH level between 6 and 8 should be used for
cleaning the frame.
Inspect terminals, cables and cable clamps at regular intervals.
T e power cable must be unplugged before attempting any
service work on the table.
All moving parts are lubricated at the factory and are therefore
free from maintenance.

www.gigant.co.uk