Giovenzana GSL30 User manual

Strawinskylaan 1105
1077 XX Amsterdam, The Netherlands
1 / 12
Giovenzana International B.V. reserves the right to change the features and data shown in this document at any time and without notice.
This document cannot therefore be considered a contract with third parties.
EN
translation of the original instructions
GSL30
GSL60
MT-GSL-EN / 21.05.2021
Rev. 3
SILICONE LED STRIPS
CONNECTIONS AND ACCESSORIES ................ 2
GSLC001 - Cable-profiled .........................2
GSLC002 - Profiled silicone end cap for power ....... 2
GSLC003 - Profiled silicone end cap terminations..... 2
GSLC004 - Profiled screw set ...................... 2
GSLC005 - LED strip tensioners (2 pieces) ...........2
GSLC006 - Wall plugs ............................3
GSLC007 - LED sealant ...........................3
GSLC008 - Profiled connection set ................. 3
GSLC009 - Profiled - profiled.......................3
GSLC010 - Profiled bridge connector ...............3
GSLC011 - Profiled T connector .................... 3
GSLC012 - Profiled cross connector ................ 3
INSTALLATION .................................. 4
General considerations ........................... 4
Operazioni preliminari ............................ 4
Strips connection ................................4
Power connections .............................. 4
Mounting using Giovenzana tensioner ..............5
Top fixture......................................5
Bottom fixture...................................6
FIXING THE WALL PLUGS.........................8
TECHNICAL CARACHTERISTICS ................... 9
Flexible strips GL30 and GL60 .....................9
Cables GSLC001 and GSLC009 ...................10
Connectors GSLC0010, GSLC011 and GSLC012 .....11
Before use, read this booklet carefully to
acquaint yourself with the features of the
product. This booklet is an integral part of
the product and therefore must be kept until
the product is dismissed.
Improper installation or tampering can cause
serious damage to people and property,
therefore installation and maintenance must
be carried out by specialized and authorized
personnel.
The device is not intended for use in
environments with a potentially explosive
atmosphere or in the presence of corrosive
substances and in salt fog.

2 / 12GIOVENZANA INTERNATIONAL B.V. - MT-GSL-EN / 21.05.2021 - Rev. 3
Giovenzana provides all the components and
accessories needed for installation and power
connection. The connectors are designed with a
patented profiled technology.
We recommend the use of our components and
accessories in order to ensure correct system
performance.
GSLC001 - Cable-profiled
GSLC003 - Profiled silicone end cap
terminations
GSLC004 - Profiled screw set
GSLC005 - LED strip tensioners (2 pieces)GSLC002 - Profiled silicone end cap for
power
CONNECTIONS AND ACCESSORIES
GSLC002
GSLC004
GSLC012
GSLC010
GSLC011
GSLC009
GSLC001
• Connect power
line cable to
LED strips.
• To be
connected to
the shaft light.
• Insulates the LED strip
termination.
• LED strip mechanical and electrical
connection with caps to cover screws and
LED sealant.
• Part that tensions the LED strip.
• Insulates the input
power cable.

3 / 12GIOVENZANA INTERNATIONAL B.V. - MT-GSL-EN / 21.05.2021 - Rev. 3
GSLC006 - Wall plugs GSLC009 - Profiled - profiled
GSLC010 - Profiled bridge connector
GSLC011 - Profiled T connector
GSLC012 - Profiled cross connector
GSLC007 - LED sealant
GSLC008 - Profiled connection set
• For LED strip mounting.
• Distance between plugs: 1.5m
for vertical installation, 0.5m for
horizontal installation.
• On request.
• Connects two LED strips at a flexible angle.
• Connects two LED strips in a straight
line.
• Connects three LED strips.
• Connects four LED strips.
• Sealant that provide
the proper insulation.
• On request.
• 90 ml
Cable-profiled
Profiled screw
set
Profiled
silicone
end cap
terminations
Profiled
silicone end
cap for power
5 ml LED sealant

4 / 12GIOVENZANA INTERNATIONAL B.V. - MT-GSL-EN / 21.05.2021 - Rev. 3
INSTALLATION
Preliminary operations
• Measure the installation and mark the anchor points.
We recommend 1.5 metres between anchor points
for vertical sections and 0.5 metres for horizontal
sections.
• The area must be free of dust and dirt for adequate
adhesion. Clean only with a dry or slightly damp cloth.
DO NOT use any acid or alkaline liquids, cleaning
agents, or solvents.
• Select all the accessories and components needed to
complete the installation.
• Cut the strips using a sharp tool only on the areas
indicated.
General considerations Strips connection
Power connections
• DO NOT MODIFY, deform or cut the strips or any of
the components provided by Giovenzana. Giovenzana
AC strips are designed to work directly plugged into
an AC source. No power supply unit is needed. To
avoid any malfunctions of the system, and to protect
against electrical shock, fire, or physical injury, please
observe the following: This system has been designed
to work at 240VAC. Connection to a line voltage other
than that may create a safety and fire hazard and may
damage the system. If you are unsure of the type of
power supply, consult your local power company or a
qualified service technician.
• TO AVOID ELECTRICAL SHOCK and/or damage to
the system, do not handle the components with
wet hands. Always make sure the LED Cable strip is
disconnected from the power source before cutting,
connecting, mounting, or modifying in any way.
• DO NOT OPERATE with the LED strip tightly coiled.
Do not puncture, cut, shorten, or splice the LED cable
strip (except where marked). For outdoor use, make
sure that all connections and the end cap in the last
segment are tightly secured to preclude the entry of
water.
• DO NOT LOOK directly into the LEDs when lit. They are
powerful and could damage your vision.
• ONLY AUTHORIZED PERSONNEL must handle and
install the strips. Follow national electric codes and
regulations during installation.
ATTENTION
For safety reasons, switch off mains power before
connecting the strip to the power source.
1
2
3
4
5
1Insert the end of the strip inside the chosen
connector as indicated
below. The copper paths
must be positioned below
the screw holes.
2Screw the connector to the strip.
3Apply sealant on top of the screw heads and
insert the screw cap,
applying pressure.
4For safety reasons, the end of the strip must be
covered with the silicone
end cap. Apply sealant
and insert the strip in the
cap.
5The power connector must be screwed on as
previously indicated.
Apply sealant and insert
the silicone end cap
covering the connector
and the strip as shown
below.

5 / 12GIOVENZANA INTERNATIONAL B.V. - MT-GSL-EN / 21.05.2021 - Rev. 3
Mounting using Giovenzana tensioner
Top fixture
(1) Locking cable tie hole
(2) Strip insertion area
(3) Hole for screw (Ø6mm)
(4) Strip final position
1
ATTENTION
Use the area of the strip without
LEDs to fix the strip in the
tensioner.
1Pass the strip through the insertion areas until the final position is reached as indicated in the drawings
on the right.. First 1 and then 2.
2Insert and tighten the locking
cable tie. This cable tie will
assure the correct position of the
strip.
2
3
4b
4a
4c
ATTENTION
Make sure that the length of
the remaining strip is enough to
lighten the additional areas as
needed.
4Screw the tensioner on the desire position of the wall using the 6mm diameter hole (+) (a). Make sure that the LED strip is
in the right position and tightly close the fixing cable ties (b).
Screw the tensioner on the wall using the 6mm diameter hole
(-) (c).
3Insert the fixing cable ties
wrapping the strip against the
tensioner. Do not tighten the
cable ties yet.
(1)
(1)
(3)
(4)
(4)
(3)
(4)
(1)
(2)
(2)
(2)
(1)
(1)
(1)

6 / 12GIOVENZANA INTERNATIONAL B.V. - MT-GSL-EN / 21.05.2021 - Rev. 3
5Arrange a rope by connecting it to the hole with a diameter of
6 mm (+) in the lower tensor.
This cord must be at least the
same length as the height of the
elevator shaft.
7From the bottom of the shaft, pull the cord down together with the
down tensioner in order to place
the strip in the correct position.
Once the down tensioner is in
the desired position, remove the
cord and proceed to mount it as
follows.
8Pass the strip through the insertion areas until the final
position is reached as indicated
in the drawings on the right (first
1 then 2 and finally 3).
5
6
6Below the already mounted top tensioner, put the strip through
the down tensioner as shown in
the picture.
ATTENTION
In cases where any additional
areas need to be lit, use wall
plugs and cable ties to fix
the strip (distance between
wall plugs 0.5m for horizontal
sections and 1.5m for vertical
sections). See section “FIXING
THE WALL PLUGS”.
7
8
Bottom fixture

7 / 12GIOVENZANA INTERNATIONAL B.V. - MT-GSL-EN / 21.05.2021 - Rev. 3
9Insert and tighten the locking cable tie. This
cable tie will ensure
the correct position of
the strip.
10 Insert the fixing cable ties wrapping
the strip against the
tensioner. Do not
tighten the cable
ties yet.
12 Screw the tensioner on the wall using
the 6mm diameter
hole (-).
11 Screw the tensioner on the wall at the
desired position
using the 6mm
diameter hole (+).
ATTENTION
Make sure that the
LED strip is in the
right position and
tightly close the
fixing cable ties.
ATTENTION
Make sure that the cable ties are properly tightened and the length of the remaining strip is enough to lighten the
additional areas. In cases where any additional areas need to be lit, use wall plugs and cable ties to fix the strip (distance
between wall plugs 0.5m for horizontal sections and 1.5m for vertical sections).
910
11
12

8 / 12GIOVENZANA INTERNATIONAL B.V. - MT-GSL-EN / 21.05.2021 - Rev. 3
FIXING THE WALL PLUGS
1Drill a 9 mm hole into the wall to which the LED strip is to be attached.
2Force the plug into the hole with the help of a suitable hammer.
3Place a cable tie in the wall plug head.
4Position the LED strip centering it on the head of the plug. 5Tighten the cable tie to secure the LED strip to the plug.
ATTENTION
Make sure that the distance between
plugs is 1.5m for vertical sections (a)
and 0.5m for horizontal sections (b).
ATTENTION
Cable ties must be fixed over
the areas of the strip without
LEDs.
1
Ø 9 mm
(b)
(a)
2
3
4
5
ATTENTION
The LED strip must be mounted
on a non-combustible surface.

9 / 12GIOVENZANA INTERNATIONAL B.V. - MT-GSL-EN / 21.05.2021 - Rev. 3
TECHNICAL CARACHTERISTICS
GSL30 GSL60
Voltage 240 V ac 240 V ac
Power 3.2 W/m 6.4 W/m
Flux 300 lm/m 600 lm/m
Protection with accessories GSLC002, GSLC003 e GSLC004 IP 65 IP 65
Operating temperature -40 ... +70°C -40 ... +70°C
UV rating F1 F1
Flame retardant V0 V0
Resistant class UL94 UL94
Anti-glare treatment market standard UGR <25 UGR <22 UGR <22
Beam angle 120° 120°
Shaft area 3.5 m² 9.2 m²
Coil 300 m 300 m
Cutting points distance 1.5 m 1 m
Flexible strips GSL30 and GSL60
• VOC free (Volatile Organic Compound).
• Silicone has excellent resistance to oil, solvents and other chemicals.
• High flexibility and mechanical resistance.
• Dimmable & flickerless with PF > 0.85.
• Different lengths available.
• As a safety measure, a maximum of 16 A circuit-breaker, category B is required.
500 1000 500 1000
12
3
4
9
500 500 500 500
12
3
4
9
GSL30
GSL60
1 2 3
1. Resistance
2. LED
3. Flexible PCB

10 / 12GIOVENZANA INTERNATIONAL B.V. - MT-GSL-EN / 21.05.2021 - Rev. 3
GSLC001 GSLC009
Voltage 240 V ac 240 V ac
Current max 6 A 6 A
Protection with accessories GSLC002 and GSLC004 IP 65 IP 65
Operating temperature -40 ... +70°C -40 ... +70°C
Connectors 1 2
Standard length 200 mm 100 mm
Cables GSLC001 and GSLC009
200
5
11
15
8
100
5
11
15
8
GSLC001
GSLC009

11 / 12GIOVENZANA INTERNATIONAL B.V. - MT-GSL-EN / 21.05.2021 - Rev. 3
GSLC0010 GSLC011 GSLC012
Voltage 240 V ac 240 V ac 240 V ac
Current max 6 A 6 A 6 A
Protection with accessories GSLC002 and GSLC004 IP 65 IP 65 IP 65
Operating temperature -40 ... +70°C -40 ... +70°C -40 ... +70°C
Connectable connectors 2 3 4
Connectors GSLC0010, GSLC011 and GSLC012
GSLC0010 GSLC011 GSLC012
8
8
15
Ø 4
5
11
8
11m
Ø 4
22
5
16,5
11
8
11
Ø 4
22
22
5